• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.8
• /
• pp.1150-1159
• /
• 2017

Objective: This study was conducted to evaluate various wheat supplementation levels on growth performance, blood profiles, nutrient digestibility, and pork quality in growing-finishing pigs. Methods: A total of 120 growing pigs ($[Yorkshire{\times}Landrace]{\times}Duroc$), with an average $27.75{\pm}1.319kg$ body weight, were used in growth trial. Pigs were allotted into each treatment by body weight and sex in 4 replicates with 6 pigs per pen in a randomized complete block design. Fourphase feeding programs were used in this experiment. The treatments included the following: i) corn-soybean meal (SBM) - based diet (CON), ii) corn-SBM - based diet+15% of wheat (W15), iii) corn-SBM - based diet+30% of wheat (W30), iv) corn-SBM - based diet+45% of wheat (W45), and 5) corn-SBM-based diet+60% of wheat (W60). Results: There was no significant difference in growth performance among the dietary treatments. However, the gain-to-feed (G:F) ratio tended to increase (quadratic, p<0.08) when the pigs were fed a higher wheat diet during the finishing period. The digestibility of crude ash and fat tended to decrease as the wheat supplementation level increased (p<0.08). The proximate analysis of the longissimus muscle was not affected by the dietary level of wheat. The crude ash content in pork was decreased linearly as the wheat supplementation level increased (p = 0.05). There was no significant difference in the pH level, shear force, water holding capacity, and cooking loss of the pork. In pork and fat, $L^{\star}$, $a^{\star}$, and $b^{\star}$ values were not significantly different among dietary treatments. Conclusion: Wheat can be supplemented up to 60% in a growing-finishing pig without detrimental effects on growth and pork quality. The G:F ratio tended to improve in the finishing period by wheat inclusion.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.30 no.1
• /
• pp.52-59
• /
• 2008

The geometric design of an implant surface may play an important role in affecting early osseointegration. It is well known that the porous surfaced implant had much benefits for the osseointegration and the early stability of implant. However, the porous surfaced implant had weakness from the transgingival contamitants, and it resulted in alveolar bone loss. The other problem identified with porous surface implant is the loss of physical properties resulting from the bead sintering process. In this study, we developed the new bead coating implant to overcome the disadvantages of porous surfaced implant. Ti-6Al-4V beads were supplied from STARMET (USA). The beads were prepared by a plasma rotating electrode process (PREP) and had a nearly spherical shape with a diameter of 75-150 ${\mu}m$. Two types of titanium implants were supplied by KJ Meditech (Korea). One is an external hexa system (External type) and the other is an internal system with threads (Internal type). The implants were pasted with beads using polyvinylalcohol solution as a binder, and then sintered at 1250 $^{\circ}C$ for 2 hours in vacuum of $10^{-5}$ torr. The resulting porous structure was 400-500 ${\mu}m$ thick and consisted of three to four bead layers bonded to each other and the implant. The pore size was in the range of 50-150 ${\mu}m$ and the porosity was 30-40 % in volume. The aim of this study was to evaluate the osseointegration of the newly developed dental implant. The experimental implants (n=16) were inserted in the unilateral femur of 4 mongrel dogs. All animals were killed at 8 weeks after implantation, and samples were harvested for hitological examination. All bead coated porous implants were successfully osseointegrated with peripheral bone. The average bone-implant contact ratios were 84.6 % (External type) and 81.5 % (Internal type). In the modified Goldner's trichrome staining, new generated mature bones were observed at the implant interface at 8 weeks after implantation. Although, further studies are required, we could conclude that the newly developed vacuum sintered Ti-6Al-4V bead coating implant was strong enough to resist the implant insertion force, and it was easily osseointegrated with peripheral bone.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.689-697
• /
• 2002

The dynamic loads and load-point displacements of concrete three-point bend (TPB) specimens had been measured. The average crack velocities measured with strain gages were 0.16 ㎜/sec ∼ 66 m/sec. The fracture energy for crack extension was determined from the difference of the kinetic energy for the load-point velocity and the strain energy without permanent deformation from the measure external work. For all crack velocities, there were micro-cracking for 23 ㎜ crack extension, stable cracking for 61 ㎜ crack extension at the maximum strain energy, and then unstable cracking. The unstable crack extension was arrested at 80 ㎜ crack extension except the tests of 66 m/sec crack velocity. The tests less than 13 ㎜/sec crack velocity and faster than 1.9 m/sec showed static and dynamic fracture behaviors, respectively. In spite of much difference of the load and load-point displacement relations for the crack velocities, the crack velocities of dynamic tests did not affect on fracture energy rate during the stable crack extension due to the reciprocal action of kinetic force, crack extension and strain energy. During stable crack extension, the maximum fracture resistances of the dynamic tests was 147％ larger than that of the static tests.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.1
• /
• pp.107-116
• /
• 2014

A volume density of roughness correction blocks in a channel is defined and the corresponding roughness coefficient(n) is estimated by analyzing the diverse hydraulic characteristics of VR, the product of the average velocity and the hydraulic radius, block Reynolds number ($Re^*$), drag coefficient ($\acute{C}_D$), and the roughness coefficient ($n_b$) of bottom shear. The increase of VR and block Reynolds number causes the exponential decrease of roughness coefficient converged to a constant value as expected. The drag coefficient also exponentially decreases as block Reynolds number increases as well. The drag force is governed by the block shape defined by volume density in high block Reynolds number of turbulent flow region. For more accurate estimation of roughness coefficient the use of the correlation equation of it is required by block Reynolds number and volume density. The regression equations for n-VR, $\acute{C}_D-Re^*$, and $n_b-\acute{C}_D$ are presented. The regression equations of roughness coefficient are also presented by block Reynolds number and volume density. The developed equation of roughness coefficient by block Reynolds number and volume density has practical use by confirming the coincidence between the experimental results and the results of HEC-RAS using the developed equation.

• Membrane Journal
• /
• v.17 no.2
• /
• pp.124-133
• /
• 2007

In this study, we treated lake water by 2 kinds of multichannel ceramic micro filtration membranes. We could investigate effects of $N_2-back-flushing$ time (BT) and transmembrane pressure (TMP), and find optimal operating conditions. The BT were changed in $10{\sim}60$ sec, TMP in $0.6{\sim}2.0$ bar at fixed filtration time (FT) 8 min, flow rate 2.0 L/min and back-flushing pressure 2.0 bar. Also, the optimal conditions were discussed in the viewpoints of resistance of membrane fouling $(R_f)$, dimensionless permeate flux $(J/J_o)$, permeate flux (J) and total permeate volume $(V_T)$. As result, optimal back-flushing conditions for HC04 ($0.4{\mu}m$ pore size) and HC10 membrane $(1.0{\mu}m)$ were BT=10 sec and BT=20 sec, respectively. Then, higher TMP should increase the driving force, and could produce more VT. Average rejection rates of pollutants were higher than 95.4% for turbidity, $12.7{\sim}20.1%\;for\;COD_{Mn},\;0.0{\sim}6.4%\;for\;NH_3-N,\;1.9{\sim}4.6%$ for T-N and $34.9{\sim}88.4%$ for T-P.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.47 no.6
• /
• pp.1-7
• /
• 2010

This paper presents a novel implementation on multimedia fingerprinting algorithm based on BCH (Bose-Chaudhuri-Hocquenghem) code. The evaluation is put in force the colluder detection to n-1. In the proposed algorit hm, the used collusion attacks adopt logical combinations (AND, OR and XOR) and average computing (Averaging). The fingerprinting code is generated as below step: 1. BIBD {7,4,1} code is generated with incidence matrix. 2. A new encoding method namely combines BIBD code with BCH code, these 2 kind codes are to be fingerprinting code by BCH encoding process. 3. The generated code in step 2, which would be fingerprinting code, that characteristic is similar BCH {15,7} code. 4. With the fingerprinting code in step 3, the collusion codebook is constructed for the colluder detection. Through an experiment, it confirmed that the ratio of colluder detection is 86.6% for AND collusion, 32.8% for OR collusion, 0% for XOR collusion and 66.4% for Averaging collusion respectively. And also, XOR collusion could not detect entirely colluder and on the other hand, AND and Averaging collusion could detect n-1 colluders and OR collusion could detect k colluders.

• Korean Journal of Poultry Science
• /
• v.31 no.4
• /
• pp.255-263
• /
• 2004

Two experiments were conducted to evaluate the feeding values of sesame oil meal (SOM) and to investigate the effects of its dietary supplementation on egg production in laying hens. In experiment I, the values of true metabolizable energy (TME), nitrogen corrected true metabolizable energy (TMEn) and true amino acid availability (TAAA) were determined by force-feeding 16 ISA-Brown roosters and collecting the total excreta from the birds, The TME and TMEn of SOM were 2.30 and 1.99 kcal/g, respectively, and the average TAAA of 15 amino acids was $76.93\%$. In experiment 2, a total of ninety, 48 weeks old ISA-Brown layer were randomly divided into 9 groups of 10 birds each and assigned to three experimental diets containing 0, 5 and $10\%$ SOM for 4 weeks (30 birds per treatment). The inclusion of SOM into laying hen diets at the 5 and $10\%$ level did not affect production and quality of egg. The C18:3 $\omega$3 content of egg yolks in the $10\%$ SOM group was higher than the other groups, but not significantly. There were no adverse effects on blood parameters in layers fed treated diets containing $5\%$ or $10\%$ SOM, The results indicate that SOM can be used for layers diet up to $10\%$ without any significant negative effects on egg production and quality.

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.19-31
• /
• 1994

The objective of this study is to conduct a thermal-hydraulic analysis on the spent fuel pool and to evaluate a parametric effect for the thermal-hydraulic analysis of spent fuel pool. The selected parameters are the Reynolds Number and the gap flow through the oater gap between fuel cell and fuel bundle. The simplified flow network for a path of fuel cells is used to analyze the natural circulation phenomenon. In the flow network analysis, the pressure drop for each assembly from the entrance of the fuel rack to the exit of the fuel assembly is balanced by the driving head due to the density difference between the pool fluid and the average fluid in each spent fuel assembly. The governing equations ore developed using this relation. But, since the parameters(flow rate, pressure loss coefficient, decay heat, density)are coupled each other, iteration method is used to obtain the solution. For the analysis of the YGN 3&4 spent fuel rack, 12 channels are considered and the inputs such as decay heat and pressure loss coefficient are determined conservatively. The results show the thermal-hydraulic characteristics(void fraction, density, boiling height)of the YGN 3&4 spent fuel rack. There occurs small amount of boiling in the cells. Fuel cladding temperature is lower than 343.3$^{\circ}C$. The evaluation of parametric effect indicates that flow resistances by geometric effect are very sensitive to Reynolds number in the transition region and the gap flow is negligible because of the larger flow resistance in the gap flow path than in the fuel bundle.

• The Journal of the Korea Contents Association
• /
• v.14 no.11
• /
• pp.695-701
• /
• 2014

The Police force and other public sector organizations do not like non-ethical evaluation of their members and disclosure of evaluation results. However, it is essential for survival and growth of the organization to identify, measure and resolve accurately the non-ethical behaviors of their members. In this study, the dimensions of police officers' unethical behavior were categorized as negligence, personal use, dishonesty, and misconduct of police officers, and the level of those dimensions were measured. After that, the differences due to the individual and work environmental characteristics were explored. The result showed that the level of non-ethical behavior was lowerer than the average. And the differences was statistically significant according to gender, rank of organization, deployed department of the work, and the period of work duration. This implied the necessities of education of police ethics, ethical atmosphere, and establishment of ethical system per differences in individual and work environmental characteristics. Also, considering the fact that the low level of ethical behavior did not lead to ethical action in actual and the inherent problem in research method how frankly the respondents answered the negative self-evaluation, continuous interest in non-ethical behavior and further systemic research are needed in a dimension of personnel management.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.2
• /
• pp.137-145
• /
• 2008

An experimental study was performed in order to investigate the influence of Reynolds number on the drag coefficient variations of an oscillating airfoil. A NACA 0012 airfoil was sinusoidally pitched at the quarter chord point with an oscillating amplitude of ${\pm}6^{\circ}$. The free-stream velocities were 1.98, 2.83 and 4.03 m/s and the corresponding chord Reynolds numbers were $2.3{\times}10^4$, $3.3{\times}10^4$ and $4.8{\times}10^4$, respectively. The drag coefficient was calculated from the ensemble average velocity measured by an X-type hot-wire probe(X-type, 55R51) in the near-wakes region. In the case of Re=$2.3{\times}10^4$, variation of drag coefficient shows a negative damping (counter-clockwise variation), which implies an unstable state which could be excited by aerodynamic force, whereas the drag coefficient represents the positive damping (clockwise variation) as the Reynolds number increases from Re=$3.3{\times}10^4$ to $4.8{\times}10^4$. Hence, the drag coefficient variations show significant differences between Re=$2.3{\times}10^4$ and $4.8{\times}10^4$이다.