• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.132-142
• /
• 1999

In this paper, a new formula for primary and secondary thrust of metal belt CVT is proposed considering variation of band tension, block compression and active arc for each of the primary and secondary pulleys. For the secondary thrust, effective friction coefficient is introduced considering the effect of flange deflection. Nondimensional primary and secondary thrust of the metal belt CVT by the new formula agree well with the experimental results except for low torque range, $0\;<\;{\lambda}\;<\;0.2$ at speed ration i = 1.0. The new formula can be used in design of the primary and secondary thrusts control system for the metal belt CVT.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.114-120
• /
• 2000

Friction forces of piston rings for a typical SI engine were independently measured while excluding the effects of cylinder pressure, oil starvation and piston secondary motion using a floating liner system. Friction patterns, represented by the measured friction forces, were classified into five frictional modes with regard to the combination of predominant lubrication regimes(boundary, mixed and hydrodynamic lubrication) and stroke regions(mid-stroke and dead centers). The modes were identified on the Stribeck diagram of the dimensionless bearing parameter and friction coefficients which were evaluated at the mid-stroke and at the dead centers. And the frictional modes were estimated to the full operation range. The compression rings behave in the mode where hydrodynamic lubrication is dominant at the mid-stroke and mixed lubrication is dominant at the dead centers under steady operating conditions. However, the oil control ring behave in the mode where mixed lubrication is dominant throughout the entire stroke.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.218-228
• /
• 1996

The behaviors of the mixture at the downstream of throttle valve in a TBI type gasoline engine plays a greater role in design of intake system. A good mixture has been influencing directly not only on the engine power but also on the pollutant emission. The mixture flow in an intake manifold is very complex, and the flow characteristics are varied with the valve type, valve angle, inlet air flow rate, and the other flow factors. Three kinds of valve are chosen in this study, and the informations of the mixture flow are observed experimentally using a PIV apparatus. Perforate valve has a smaller recirculation zone than the case of solid valve with a lower valve loss coefficient, and iti is verified that the perforated valve is also suitable to control the flow rate in a mixture flow system.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.5-11
• /
• 1987

선진국에서 사용되고 있는 자동차 배기정화 장치의 성능평가 시험방법은(CVS테스트, 유럽테스트, 일본테스트법 등)배기정화용 3원촉매 뿐만 아니라 그 부수장치의 성능을 포함한 포괄적인 평가방 법이므로 그 결과에 미치는 인자가 대단히 복잡하고 평가비용과 시간도 크게 드는 결점이 있어 서, 3원촉매만의 특성평가와 새로운 촉매의 연구개발의 방향을 추출하기 위하여서는 개선된 새로 운 성능 평가방법이 요구되고 있다. 이에 부응하여 모조합성 배기가스를 이용환 촉매성능측정장 치로부터 실제 엔진배기사스 측정장치에 이르까지 많은 평가시험 방법이 제안되었으나 아직 이러 한 시험방법에 의한 결과와 해석에 대하여서는 많은 관찰의 소지를 남기고 있는 것으로 보고 되 고 있다. 따라서, 본고에서는 기존상업적 3원촉매 뿐만 아니라 앞으로 연구 개발될 새로운 3원 촉매의 특성 및 성능평가에 관하여 미국, 일본 등을 포함한 선진제국의 현행 평가방법을 주로 초기단계에서 제안된 일본자동차연구소 연구보고 중심으로 하여 고찰하고자 한다.

• Journal of the korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.46-55
• /
• 1982

When an oxidizing catalytic converter which makes use of platium as a catalyst is employed by means if emission control of CO and HC gasoline engine, the effects of important factors for the purification efficiency, i.e engine speed and secondary air rate, on the reduction of CO and HC concentrations in the exhaust gas are studied experimentally. In the experiment, gasoline and LPG are used as a fuel, and the purification efficiency is examined and the results of both cases are compared with each other. The experimental results showed that the purification efficiency in the case of LPG is usually higher than that of gasoline, and the optimum values of engin speed and secondary air rate for maximum purification efficiency exist in common on both cases.

• International Journal of Automotive Technology
• /
• v.7 no.2
• /
• pp.195-199
• /
• 2006

According to the United States FMVSS 208, every passenger car on the market after September of 2006 must install a safety system, which can deploy the airbag with different intensity or suppression based on the passenger type, to reduce infant and child injuries from airbag deployments. The Weight Classification System, which has been developed by Hyundai Autonet, is a system that classifies the person occupying the passenger seat. To overcome sensing problems due to the weight sensors small voltage, the Distributed Systems Interface is adopted.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.56-64
• /
• 2000

A friction force measurement system using the floating liner method was developed to study the frictional behavior of piston rings. The measurement system was carefully designed to control the effect of the piston secondary motion and the temperature of cylinder wall and oil. The friction force between the barrel shaped piston ring and the cylinder liner, was measured under the condition of flooded oil supply. The measured friction forces were classified into five frictional modes with regard to the combination of predominant lubrication regimes(boundary, mixed and hydrodynamic lubrication) and stroke regions(midstroke and dead centers). The modes could be identified on the Stribeck diagram of the friction coefficients and the dimensionless number of ㎼/p, where the friction coefficients are evaluated at near the midstroke and dead centers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.24-33
• /
• 1999

This paper investigate the effects of the variations of engine operation condition in the flame kernel formation and developmnet . A model for calculating the initial kernel development in spark ignition engines is formualted. It considered input of electrical energy, combustion energy release and heat transfer to the spark plyg, cylinder head, and unburned mixture. The model also takes into accounts strain rate of initial kernel and residual gas fraction. The breakdown process and the subsequent electrical power input initially control the kernel growth while intermediate growth is mainly dominated by diffusion or conduction. Then, the flame propagates by the chemical energy and turbulent flame expansion. Flame kernel development also influenced by engine operating conditions, for example, EGR rate, air-fuel ration and intake manifold pressure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.190-198
• /
• 1999

Continuously controlled semi-active suspension system may improve ride and handling properties. Here, as a mechanism to control the fluid flow solenoid valve mechanism is introduced and added to the basic passive damper to create damping forces of the shock absorbers. The system may produce continuously controlled damping forces in both solenoid valve only and combination with passive shock absorber including fluid flow is studied, and then the combined model is added to the full vehicle model to evaluate its ride and handling performance. Finally, the simulation results are compared to the vehicle models having similar suspension system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.36-43
• /
• 1997

To cope with quest to improve the fuel economy and vehicle performance, Continuously Variable Transmission with Changing the speed ratio between minimum and maximum ratio by infinite step, is more efficient than conventional multi-ratio transmission. In this paper, to investigate a specific CVT shift ratio diagram and CVT shift characteristics, CVT vehicle was tested on the proving ground and chassis dynamometer. The test results are as follows; CVT can obtain the excellent vehicle performance and fuel economy changing the shift ratio by infinite step, without rapid change of engine revolution and driving force. And CVT can set up a special shift range that obtains not only the engine brake effect but also the maximum speed driving.