• Nuclear Engineering and Technology
• /
• v.56 no.6
• /
• pp.2113-2119
• /
• 2024

This study presents the development and characterization of a prototype TL/OSL reader for the retrospective dose assessment of individuals in radiological emergencies. The reader is portable, semi-automatic, and capable of accurate measurements. The dimension of the reader is 25 × 25 × 37 cm³ and the weight is about 15 kg. The reader consists of a sample moving stage, a heating module, an optical stimulation module, a detection module, a data acquisition (DAQ) unit, a nitrogen gas control module, and a PC with a GUI program. The reader has three measurement modes: TL, CW_OSL, and custom mode. The reader was characterized using commercial thermal luminescence dosimeters (TLD, LiF:Mg,Cu,Si) and optically stimulated dosimeters (OSLD, Al₂O₃:C), as well as fortuitous materials, such as display glasses and resistors of mobile phone. The results showed that the reader is capable of measuring signals with a detection limit of up to 0.02 mGy using a commercial dosimeter. In the dose recovery test using fortuitous materials, the reconstructed doses obtained three days post-irradiation closely aligned with the initially administered doses. As a result, this study suggests that the developed TL/OSL reader is a promising instrument for emergency dose assessment at accident sites.

• Journal of Broadcast Engineering
• /
• v.2 no.2
• /
• pp.146-155
• /
• 1997

The new video coding standard Iv1PEG-4 is enabling content-based functionalities. It requires a prior decomposition of sequences into video object planes (VOP's) so that each VOP represents moving objets. This paper addresses an image segmentation method for separating moving objects from still background (non-moving area) in video sequences using a statistical hypothesis test. In the proposed method. three consecutive image frames are exploited and a hypothesis testing is performed by comparing two means from two consecutive difference images. which results in a T-test. This hypothesis test yields a change detection mask that indicates moving areas (foreground) and non-moving areas (background), Moreover. an effective method for extracting

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.12
• /
• pp.1130-1135
• /
• 2015

The bond pull test is the most widely used technique for the evaluation and control of wire bond quality. The wire being tested is pulled upward until the wire or bond to the die or substrate breaks. The inspector test strength of wire by manually and it takes around 3 minutes to perform the test. In this paper, we develop a 3D vision system to measure 3D position of wire. It gives 3D position data of wire to move a hook into wires. The 3D measurement method to use here is a confocal imaging system. The conventional confocal imaging system is a spot scanning method which has a high resolution and good illumination efficiency. However, a conventional confocal systems has a disadvantage to perform XY axis scanning in order to achieve 3D data in given FOV (Field of View) through spot scanning. We propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array to remove XY scan. 2D imaging system can detect 2D location of wire and it can reduce time to measure 3D position of wire. In the experimental results, the proposed system can measure 3D position of wire with reasonable accuracy.

• Environmental Analysis Health and Toxicology
• /
• v.22 no.2 s.57
• /
• pp.171-175
• /
• 2007

Indigenous species means a species that is likely, due to historical presence, to occur at a specified site for some portion of its life span. Therefore, indigenous species can be useful as an indicator to assess environmental risk caused by hazardous chemicals in a specific site. So far a few toxicity studies using freshwater species which are indigenous to Korea have been carried out. In this study, a freshwater shrimp (Neocardina denticulata) indigenous to Korea was used for acute toxicity test of heavy metals. Neocardina denticulata were exposed to cadmium chloride $(CdCl_2)$, copper chloride $(CuCl_2)$ and zinc chloride $(ZnCl_2)$ using automatic flow-through system for 96 hours. The 96h LC50s were calculated as 0.043 $(0.042{\sim}0.045)mg\;CdCl_2/L,\;0.104(0.098{\sim}0.113)mg\; CuCl_2/L\;and\;2.021\;(1.633{\sim}2.594)mg\;ZnCl_2/L$. When compaired with some international standard species such as medaka(Oryzias latipes), Neocardina denticulata had high sensitivity. Therefore, this study suggested that Neocardina denticulata have possibilities for a sensitive test species to test heavy metal toxicity in aqua-system.

• Toxicological Research
• /
• v.18 no.4
• /
• pp.369-374
• /
• 2002

The present study was performed to validate an automated image analysis system (Loats Automated Micronucleus Scoring System) for the mouse bone marrow micronucleus assay, comparing with conventional microscopic scoring. Two studies were conducted to provide slides for a comparison of micro-nucleated polychromatic erythrocytes (MNPCEs) values collected manually to those collected by the auto-mated system. Test article A was used as an example of a compound negative for the induction of micronuclei and test article B was wed as a micronucleus-inducing agent to elicit a positive response. Cyclophosphamide was included to provide an positive control in two studies. Bone marrow samples were collected 24 h after administration of test article A and B in male ICR mice. The cells were fixed with absolute methanol and stained with May-Grunwald and Giemsa. The number of MNPCEs was determined by the analysis of 1000 total PCEs per bone marrow sample. In addition to micronucleus scoring, an index of bone marrow toxicity based on PCE ratio (% of PCEs to total erythrocytes) was determined for each sample. The automated and manual scoring was similar when the MNPCEs incidence induced by each test article was less than 10. However manual scoring was able to effectively enumerate micronucleated PCEs in mouse bone marrow when MNPCEs incidence was more than 10, such as cyclophosphamide treatment. Conversely, PCE ratio was superior in computer-assisted image analysis. Taken together, it is suggested that improvement of the automated image analysis may be necessary to render the automatic scoring as sensitive as manual scoring for routine counting of micronuclei, especially because it is superior in objectivity and high throughput scoring.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.5 no.1
• /
• pp.34-47
• /
• 1985

The developing country, KOREA where does not possess the natural resources for traditional energy such as oil and gas, so. The nuclear energy is the most single reliable source available for closing the energy gap. For these reason, It is inavoidable to construct the nuclear power plant and to develop technology related nuclear energy. The rate of operation in large nuclear power facilities depends upon the performance of work system through design and construction, and also the applied technology. Especially, it is the most important element that safety and reliability in operation of nuclear power plant. In view of this aspects, Nuclear power plant is performed severe examinations during preservice and inservice inspection. This study provide an automation of analysis for volumetric examination which is required to nuclear power plant components. It is composed as follows: I. Introduction II. Inservice Inspection of Nuclear Power Plant ${\ast}$ General Requirement. ${\ast}$ Principle and Methods of Ultrasonic Test. ${\ast}$ Study of Flaw Evaluation and Design of Classifying Formula for Flaws. III. Design of Automation for Flaw Evaluation. IV. An Example V. Conclusion In this theory, It is classifying the flaws, the formula of classifying flaws and the design of automation that is the main important point. As motioned the above, Owing to such as automatic design, more time could be allocated to practical test than that of evaluation of defects, Protecting against subjective bias tester by himself and miscalculation by dint of various process of computation. For the more, adopting this method would be used to more retaining for many test data and comparative evaluating during successive inspection intervals. Inspite of limitation for testing method and required application to test components, it provide useful application to flow evaluation for volumetric examination. Owing to the characteristics of nuclear power plant that is highly skill intensive industry and has huze system, the more notice should be concentrated as follows. Establishing rational operation plan, developing various technology, and making the newly designed system for undeveloped sector.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.414-416
• /
• 2003

As environmental conditions for memory products are increasingly high speed/high density, adopting diverse system configuration, it's more and more difficult for current component tester to adopt the actual condition of field application. If system test screening is realized in component level, test coverage failure can be made more secured in the initial stage, evaluation cost can be reduced and the effectiveness of investment for the facility can be maximized. Based on the above background, component automatic system tester was developed and showed off satisfactory results per each memory device family. In this paper, component quality stabilization strategy and cost saving for tester investment through future Quality monitoring and application to mass production will be presented.

• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.332-341
• /
• 1998

Conventional polishing of stone panel edges has been done by hand. While this has changed somewhat with the advent of automatic machines, it is still very much a hand finishing technology. For the development of edge shape milling tool, the primary test on characteristics of edge shape milling tool was carried out. This paper presents the results of tests focused upon the milling capability that was varied by the variables of operation parameters. Author tried to confirm the effect of six operation parameters of equipment such as rotation speed, advance speed, applied load, water flow rate and rotational direction. The result from test was described in term of shape milling capability that was defined as cutting volume of rock by unit weight of tool wear. The variance of the results could indicate the optimum level of each operating parameters. The test was also carried out to determine the abrasion resistance varied according to the abrasive flow rate. The abrasion resistance was increased with the abrasive flow rate, but over some rate it was not changed.

• Journal of Advanced Navigation Technology
• /
• v.17 no.5
• /
• pp.560-567
• /
• 2013

In this paper, it is proposed the fault detection method of the ASIC, without the Test Requirement Document(TRD), extracting internal logic circuit and analyzed the function of the ASIC using the multipurpose development program and simulation. If there don't have the TRD, it is impossible to analyze the operation of the circuit and find out the fault detection in any chip. Therefore, we make the TRD based on the analyzed logic data of the ASIC, and diagnose of the ASIC circuit at the gate level through the signal control of I/O pins using the Dynamic Pattern signal. According to the experimental results of the proposed method, we is confirmed the good performance of the fault detection capabilities which applied to the non-memory circuit.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1472-1479
• /
• 2018

The purpose of this study was to investigate the ability to maintain dynamic posturography(EquiTest) in gymnastic, freestyle skier, and figure skater. A total of 32 subjects(22 athletic woman and 10 collegiate woman) were participated in this study. Computerized dynamic posturography(EquiTest) was adopted to test sensory organization and motor control. EquiTest facilitated the quantification of the role of somatosensory, visual and vestibular systems in the maintenance of postural balance and was also pertinent to measure the reaction time to the stimulus to change center of gravity on force platform. As a result were as follow. There was not difference among with exercise group. But there was a significantly difference with between groups. It was suggested that the acrobatic and physical activity developed the function of visual system and the role of the combination of visual and vestibular system in maintaining postural balance to surrounding stimulus, and presented shorter reaction time in automatic postural response.