• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.2
• /
• pp.38-44
• /
• 1994

Control Algorithms of the Auto-Pilot system have been studied for the navigational economics and crew's comfortability since 1960's, when Auto-Pilot system was installed on the trans-ocean ships. At the beginning the PD control algorithm was used with the weather adjust function introduced to reduce the response of the auto-pilot system to the high frequency wave excitation in rough sea. In this study, the optimal and adaptive control theories are applied for the auto-pilot control algorithm. And those two algorithms are compared through the pre-defined cost function to obtain the most effective control technique for the Auto-Pilot system. The parameterization of the ship meneuvering equation for the adaptive control algorithm design procedure was examined and the advantage of the adaptive control was found through the simulation result with the wrong initial parameter value.

• Fire Science and Engineering
• /
• v.24 no.3
• /
• pp.106-112
• /
• 2010

This study carried out the motion analysis of auto closing systems as basis study for development of auto closing systems for door in smoke control zone. This study established process of auto closing systems and analysis theory based on kinematics mechanism thesis and mechanism modelling of auto closing control units. And this study established engineering data construction and a source technology that can design each element of auto closing control units that choose closing force units through motion analysis simulation based on analysis theory. Therefore, it can give flexibility and elasticity of auto closing units development from this study. Also, it sees that can ready control means and technological countermeasure of smoke by development of auto closing units and secure high reliancity and stability of smoke control systems.

• Journal of Advanced Navigation Technology
• /
• v.13 no.6
• /
• pp.813-819
• /
• 2009

Designing actuator controllers of aircraft, which control aileron, flap, elevator and so on, is quiet difficult, because they have time variant nonlinear mechanical structures and also have many kinds of disturbances which are not been able to model easily. This paper reports about the performance of Fuzzy Auto gain tuning Control algorithm applied unmaned aerial vehicle. Fuzzy Auto gain tuning PID control uses PID control and Fuzzy control, therefore It can be applied very easily and it also has advances of PID control. It can control a unmaned aerial vehicle actuators adaptively even though the designer does not have enough information of plant.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.1
• /
• pp.64-70
• /
• 2002

This paper shows the results of the development of a small size of digital type continuous and intermittent welding auto-carriage based on microprocessor (Intel 80196KC) for welding process with long welding line. The developed welding auto-carriage loads welding torch and tracks welding line. It is an automaton largely used for welding process with a lot of long welding lines such as shipbuilding and structure. Most traditional auto-carriages have been developed based on analog circuit for open loop control. So this analog circuit welding auto-carriage cannon control welding speed. Specially welding auto-carriage for intermittent welding condition is so complicated and has the low precision of control performance in welding distance and non-welding distance. The auto-carriage developed in this paper has the following characteristics: It has not only functions of traditional carriage but also functions such as pseudo-welding process of big iron structures, intermittent welding in order to limit heat for welding thin plates, crater treatment of the final step of welding, acceleration at the initial step of welding and deceleration in the final step of welding. The main control board of auto-carriage, power supply system and DC motor drive wee developed and manufactured. The welding speed and the welding distance of the developed auto-carriage are controlled accurately by feedback control using photo-sensor. Hardware and software robust against the heat and noise produced on the welding process are developed.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.203-206
• /
• 1998

This paper describes the procedure of getting information about auto-tuning of PID regulator by the injection of high step input, called limited input, during a transient time of control. The key point is that system identification and control could be continuously executed. This means that the system information obtained by limited input despite of system uncertainty can be continuously applied to the PI regulator. Simulation and experiment result of brushless DC motor system having monotone increasing step response demonstrate the usefulness of proposed auto-tuning algorithm.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.347-360
• /
• 2014

The auto-berthing of a ship requires excellent control for safe accomplishment. Crabbing, which is the pure sway motion of a ship without surge velocity, can be used for this purpose. Crabbing is induced by a peculiar operation procedure known as the push-pull mode. When a ship is in the push-pull mode, an interacting force is induced by complex turbulent flow around the ship generated by the propellers and side thrusters. In this paper, three degrees of freedom equations of the motions of crabbing are derived. The equations are used to apply the adaptive backstepping control method to the auto-berthing controller of a cruise ship. The controller is capable of handling the system non-linearity and uncertainty of the berthing process. A control allocation algorithm for a ship equipped with two propellers and two side thrusters is also developed, the performance of which is validated by simulation of auto-berthing.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1008-1011
• /
• 1996

Most control systems of power plants are using classical PID controllers for their process control. In order to get the desired control performances, the correct tuning of PID controllers is very important. Sometimes, it is necessary to retune PID controllers after the change of system operating condition and system design change, etc. Commercial auto-tuning controllers such as relay feedback controller can be used for this purpose. However, using these controllers to the safety-critical systems of nuclear power plants may be cause of unsafe operation, because they are using test signals for tuning. A new system identification auto-tuning method without using test signal has been developed in this paper. This method uses process input/output signals for system identification of unknown control process. From the model information of control process which was obtained from system identification approach, the optimal PID parameters can be calculated. The method can be used in the safety-critical systems because it is not using test signals during system modeling process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.351-357
• /
• 2003

An easy learning elevator originated is opened to compare the existed teaming equipment, and it had a high studied efficiency that the sequence control circuit can open and close with the wire. The structure of equipment to be controlled from the first floor to the fifth floors is demostrated by the constructive apparatus with the lamps to express the function of the open-close of the door according to the cage moving with a mechanical actuation of the forward reverse breaker and the motor of load, and the mechanical actuation of hand-operation control components of push-button S/W and L/S and relay etc. These components let connect each other in order to control of the elevator function with the auto program and the designed sequence control circuit. Consequently the cage could go and come till 1∼5 steps with an auto program of the elevator and the sequence control circuit. The sequence control circuit is controlled by the step of forward and reverse to follow as that the sensor function of L/S1 ∼ L/S5 let posit with the control switchs of S/W1 ∼ S/W5 of PLC testing panel and switchs of S/W1 ∼ S/W5 installed on the transparent acryl plate of the frame. In here, improved apparatus is the hand-auto operation combined learning equipment to study the principle and technique of the originate sequence control circuit and the auto program of PLC.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.62-62
• /
• 2000

An auto-tuning PID controller which is adequate for temperature control is developed based on relay-control and pole-placement Using the critical frequency which is obtained from relay-control parameters of assumed model are identified. Pole/zero-placement PID controller is designed for the identified model. The desired pole/zeros are determined so that the closed-loop has overshoot free step response. The developed auto-tuning PID controller was successfully applied to the temperature control of RTP.

• Transactions on Control, Automation and Systems Engineering
• /
• v.1 no.2
• /
• pp.141-146
• /
• 1999

This paper describes the communication method of an auto-startup system. The Auto-Startup system is designed to operate a nuclear power plant automatically during the startup operation . In general , the operations during startup in existing plant have only been manually controlled by the operator. The manual operation caused to the operator mistake. The Auto-Startup system consists of the Distributed Control System(DCS) and G2 (Expert System). Also, Functional Test Facility(FTF) provides the plant's real-data for an Auto-Startup system. So, it is necessary to develop the communication method between these systems. We developed two methods ; one is a network and the other is a hardwire line. To communicate between these systems (DCS-G2 and DCS-FTF) , we developed the communication program. In case of DCS-FTF, we used the TCP/IP and VXI. BUt, in case of DCS-G2 , we , what it called , developed the bridge program using the GSI(G2 Standard Interface). We test to check the function of the important parameter, in time, for analysis of the developed communication method. The results are a good performance when we check the communication time of important parameter. We conclude that Auto-startup system could save heat-up time about at least 5 hours and reduced the change of the reactor operation and trip.