본 연구에서는 완전동형암호로 암호화된 데이터에 적용할 수 있는 가산기 및 다수개의 데이터를 가산할 때 적용할 수 있는 성능이 향상된 가산 방법을 제안한다. 제안 산술 가산기는 기존의 하드웨어 기반의 산술 가산기 중 최적 회로단계(level)를 가지는 Kogge-Stone Adder 방법을 기반으로 하며, 완전동형암호가 제공하는 암호학적 SIMD(Single Instruction for Multiple Data) 기법을 적용하기에 적합하게 설계되었다. 제안한 다수 가산 방법은 완벽한 가산 결과를 보장하는 Kogge-Stone Adder를 반복적으로 사용하여 다수개의 데이터를 가산하지 않고, 3개 이상의 수를 더해야 할 경우, Full-Adder를 이용하여 3개의 수를 최종 C(Carry-out)과 논리합의 결과인 S(Sum) 의 두 개로 줄인다. 이러한 과정을 반복하여 최종적으로 두 개의 수를 더할 경우에만 Kogge-Stone Adder를 사용하여 가산하는 방법이다. 제안 방법은 더하고자 하는 데이터의 개수가 많아질수록 성능이 비약적으로 향상되었고, 이를 실험을 통해 검증한다.
본 논문에서는 저 면적 타원곡선 암호프로세서를 위한 GF(2$^{m}$ )상의 새로운 산술 연산기를 제안한다. 제안된 연산기는 바이너리 확장 최대공약수 알고리즘과 MSB(Most Significant Bit) 우선 곱셈 알고리즘으로부터 하드웨어 공유를 통하여 LFSR(Linear Feed Back Shft Register)구조로 설계되었으며, 나눗셈 및 곱셈 모두를 수행 할 수 있다. 즉 나눗셈 모드에서 2m-1 클락 사이클 지연 후 나눗셈의 결과를 출력하며, 곱셈 모드에서 m 클락 사이클 지연 후 곱셈 결과를 각각 출력한다. 본 논문에서 제안된 연산기를 기존의 나눗셈기들과 비교 분석한 결과 적은 트랜지스터의 사용으로 계산 지연시간을 감소 시켰다. 또한 제안된 연산기는 기약다항식의 선택에 어떠한 제약도 두지 않을 뿐 아니라 매우 규칙적이고 묘듈화 하기 쉽기 때문에 필드 크기 m 에 대하여 높은 확장성 및 유연성을 제공한다 따라서, 본 연구에서 제안된 산술 연산기는 타원곡선 암호프로세서의 나눗셈 및 곱셈 연산기로 사용될 수 있다. 특히 스마트 카드나 무선통신기기와 같은 저 면적을 요구하는 응용들에 매우 적합하다.
In order to solve the well-known drawback of reduced flexibility that is associate with ASIC implementations, this paper proposes a novel arithmetic unit over GF(2$^{m}$ ) for field programmable gate arrays (FPGAs) implementations of elliptic curve cryptographic processor. The proposed arithmetic unit is based on the binary extended GCD algorithm and the MSB-first multiplication scheme, and designed as systolic architecture to remove global signals broadcasting. The proposed architecture can perform both division and multiplication in GF(2$^{m}$ ). In other word, when input data come in continuously, it produces division results at a rate of one per m clock cycles after an initial delay of 5m-2 in division mode and multiplication results at a rate of one per m clock cycles after an initial delay of 3m in multiplication mode respectively. Analysis shows that while previously proposed dividers have area complexity of Ο(m$^2$) or Ο(mㆍ(log$_2$$^{m}$ )), the Proposed architecture has area complexity of Ο(m), In addition, the proposed architecture has significantly less computational delay time compared with the divider which has area complexity of Ο(mㆍ(log$_2$$^{m}$ )). FPGA implementation results of the proposed arithmetic unit, in which Altera's EP2A70F1508C-7 was used as the target device, show that it ran at maximum 121MHz and utilized 52% of the chip area in GF(2$^{571}$ ). Therefore, when elliptic curve cryptographic processor is implemented on FPGAs, the proposed arithmetic unit is well suited for both division and multiplication circuit.
XOR(exclusive-OR)-XNOR(exclusive NOR) 회로는 고 성능 산술 연산에 필요한 4-2 압축 회로(4-2 compressor)의 기본 구성 요소이다. 본 논문에서는 에너지 효율이 우수한 XOR-XNOR 회로를 제안한다. 제안한 회로는 임계 경로의 내부 기생 캐패시턴스를 감소시켜 전파 지연 시간을 감소시켰으며, 모든 입력 조합의 경우에 완벽한 출력 값을 가지며 8개의 트랜지스터로 설계되었다. 기존 회로와 비교하여 제안한 회로는 전파 지연 시간이 14.5% 감소하였으며, 전력 소모는 1.7% 증가하였다. 따라서 전력 소모와 지연 시간의 곱 (power-delay product: PDP)과 에너지와 지연 시간의 곱 (energy-delay product: EDP) 각각 13.1%, 26.0% 감소하였다. 제안한 회로는 0.18um CMOS 표준공정을 이용하여 설계하였으며 SPICE 시뮬레이션을 통해 타당성을 입증하였다.
This paper proposes a design and implementation of transversal adaptive digital filter using LMS (Least Mean Squares) adaptive algorithm. The filter structure is based on Distributed Arithmetic (DA) which is able to calculate the inner product by shifting and accumulating of partial products and storing in look-up table, also the desired adaptive digital filter will be multiplierless filter. In addition, the hardware implementation uses VHDL (Very high speed integrated circuit Hardware Description Language) and synthesis using FLEX10K Altera FPGA (Field Programmable Gate Array) as target technology and uses Leonardo Spectrum and MAX+plusII program for overall development. The results of this design are shown that the speed performance and used area of FPGA. The experimental results are presented to demonstrate the feasibility of the desired adaptive digital filter.
본 논문에서는 광컴퓨터의 개발에 이용될 수 있는 산술논리연산회로(ALU)를 설계하고 검증한다. 전자회로 기술의 접목이 용이하고 가장 상용화가 잘된 $LiNbO_3$ 광스위칭 소자에 기반한 이 ALU는 산술논리 동작을 실행하는 연산회로, 오퍼런드와 연산결과를 저장하는 메모리 소자 그리고 명령어 선택을 위한 부가회로로 구성되며, 비트 단위 직렬 방식으로 동작하는 것이다. 본 논문에서는 또한 설계한 ALU 회로의 정확성을 검증할 수 있는 시뮬레이터를 구현하고, 일련의 기본 명령어들을 순차적으로 실행하면서 메모리와 누산기에 저장된 값의 단계적 변화를 확인하는 시뮬레이션을 통하여 설계한 ALU가 정확함을 보인다.
3차원 그래픽 API인 OpenGL과 Direct3D를 효율적으로 처리하기 위해 sine, cosine, 역수, 역제곱근, 지수 및 로그 연산을 처리하는 부동소수점 연산회로를 설계하였다. 고속 연산과 2 ulp 보다 작은 오차를 만족시키기 위해 2차 최대최소 근사 방식과 테이블 룩업 방식을 사용하였다. 설계된 회로는 65nm CMOS 표준 셀 조건에서 2.3-ns의 최대 지연시간을 갖고 있으며, 약 23,300 게이트로 구성된다. 최대 400 MFLOPS의 연산 성능과 높은 정밀도로, 설계한 연산회로는 3차원 모바일 그래픽 분야에 효율적으로 적용 가능하다.
To use the SLIM for servo system, the exact account of thrust about the initial speed is needed, but analyzing by equivalent circuit analyzing methode such as rotary induction motor, the error occurs because of the end effect. So, we applied the equivalent circuit considering the end effect of SLIM in this paper. The current control system is advanced the space vector pulse width modulation by using high arithmetic performance microprocessor such as DSP. In this paper, we use the dynamic characteristic analyzing methode that can calculate efficiently the end effect by using equivalent circuit methode in the operating SLIM system modeling and examine the output characteristics of SVPWM with PI controller.
Confluence buffers and single flux quantum (SFQ) switches are essential components in constructing a high speed superconductive Arithmetic Logic Unit (ALU). In this work, we developed a SFQ confluence buffer and an SFQ switch. It is very important to optimize the circuit parameters of a confluence buffer and an SFQ switch to implement them into an ALU. The confluence buffer that we are currently using has a small bias margin of $\pm$11%. By optimizing it with a Josephson circuit simulator, we improved the design of confluence buffer. Our simulation study showed that we improved bias global margin of 10% more than the existent confluence buffer. In simulations, the minimal bias margin was $\pm$33%. We also designed, fabricated, and tested an SFQ switch operating in a DC mode. The mask layout used to fabricate the SFQ switch was obtained after circuit optimization. The test results of our SFQ switch showed that it operated correctly and had a reasonably wide margin of $\pm$15%.
캐리-세이브 가산기 (CSA)는 회로 설계 과정에서 빠른 연산 수행을 위해 가장 널리 이용되는 연산기 중의 하나이다. 그러나, 현재까지 산업체에서 CSA를 이용한 설계는 설계자의 경험에 따른 수작업에 의존하고 있고 그 결과 최적의 회로를 만들기 위해 매우 많은 시간과 노력이 소비되고 있다. 이에 따라 최근 CSA를 기초로 하는 회로 합성 자동화 기법에 대한 연구의 필요성이 대두되고 있는 상황에서, 본 논문은 연산 속도를 최적화하는 효율적인 CSA 할당 알고리즘을 제안한다. 우리는 CSA 할당 문제를 2단계로 접근한다: (1) 연산식의 멀티 비트 입력들만을 고려하여 최소 수행 속도 (optimal-delay)의 CSA 트리를 할당한다; (2) (1)에서 구한 CSA 트리의 수행 속도 증가가 최소화 (minimal increase of delay) 되는 방향으로 CSA들의 캐리 입력 포트들에 나머지 싱글 비트 입력들을 배정한다. 실제 실험에서 우리의 제안된 알고리즘을 적용하여 연산식들의 회로 속도를 회로 면적의 증가 없이 상당한 수준까지 줄일 수 있었다.Abstract Carry-save-adder (CSA) is one of the most widely used implementations for fast arithmetics in industry. However, optimizing arithmetic circuits using CSAs is mostly carried out by the designer manually based on his/her design experience, which is a very time-consuming and error-prone task. To overcome this limitation, in this paper we propose an effective synthesis algorithm for solving the problem of finding an allocation of CSAs with a minimal timing for an arithmetic expression. Specifically, we propose a two step approach: (1) allocating a delay-optimal CSA tree for the multi-bit inputs of the arithmetic expression and (2) determining the assignment of the single-bit inputs to carry inputs of the CSAs which leads to a minimal increase of delay of the CSA tree obtained in step (1). For a number of arithmetic expressions, we found that our approach is very effective, reducing the timing of the circuits significantly without increasing the circuit area.
이메일무단수집거부
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.