• International Journal of Aeronautical and Space Sciences
• /
• v.13 no.3
• /
• pp.317-322
• /
• 2012

The low speed aerodynamic characteristics for a modified sonic arc airfoil which is designed by using the nose shape function of sonic arc, the shape function of NACA four-digit wing sections, and Maple are experimentally investigated. The small rotor blades of a modified sonic arc and NACA0012 airfoil are precisely fabricated with a commercially available light aluminum(Al 6061-T6) and are spin tested over a low speed range (3000rpm-5000rpm). In a consuming power comparison, the consuming powers of NACA0012 are higher than that of modified sonic arcs at each pitch angle. The measured rotor thrust for each pitch angle is used to estimate the rotor thrust coefficient according to momentum theory in the hover state. The value of thrust coefficients for both two airfoils at each pitch angle show almost constant values over the low Mach number range. However, the rotor thrust coefficient of NACA0012 is higher than that of the modified sonic arc at each pitch angle. In conclusion, the aerodynamic performance of NACA0012 is better than that of modified sonic arcs in the low speed regime. This test model will provide a convenient platform for improving the aerodynamic performance of small scale airfoils and for performing design optimization studies.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.1
• /
• pp.59-64
• /
• 2016

This paper aims at the prototype-making of the intelligent switchgear with arc fault diagnosis function required to prevent the electrical fire. The main control unit of the intelligent switchgear consists of a single-phase power management device and a arc fault diagnosis device. The prototype of the single-phase power management device and the prototype of the arc fault diagnosis device in this paper. In the device, the cooperation function with the arc fault diagnosis device is developed to transmit the cause of the electrical fire to the remote server system.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.3
• /
• pp.349-356
• /
• 2015

Remote monitoring partial discharge sensor, equipping with hybrid filter combining optical and electrical noise reduction capabilities and with signal integrating function to calculate total arc energy, was investigated. Hybrid filter showed insensitivity to fluorescent and incandescent lamps under simulated distribution panel condition. Signal integrating function showed selective detection capability corresponding to different arc energy levels, while convention arc sensor had difficulty to discriminate arc energy level due to bursty arc waveform and peak level detection characteristics. The sensor showed possibility for application to remote monitoring partial discharge sensor, since it detected arc energy level corresponding to normal open and close discharge in low voltage 100A MCCB at 2m distance.

• Molecules and Cells
• /
• v.40 no.12
• /
• pp.889-896
• /
• 2017

Nuclear bodies are subnuclear, spheroidal, and membraneless compartments that concentrate specific proteins and/or RNAs. They serve as sites of biogenesis, storage, and sequestration of specific RNAs, proteins, or ribonucleoprotein complexes. Recent studies reveal that a subset of nuclear bodies in various eukaryotic organisms is constructed using architectural long noncoding RNAs (arcRNAs). Here, we describe the unifying mechanistic principles of the construction and function of these bodies, especially focusing on liquid-liquid phase separation induced by architectural molecules that form multiple weakly adhesive interactions. We also discuss three possible advantages of using arcRNAs rather than architectural proteins to build the bodies: position-specificity, rapidity, and economy in sequestering nucleic acid-binding proteins. Moreover, we introduce two recently devised methods to discover novel arcRNA-constructed bodies; one that focuses on the RNase-sensitivity of these bodies, and another that focuses on "semi-extractability" of arcRNAs.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.113-121
• /
• 1996

The arc sensor has been most widely used for weld seam tracking through welding current or voltage variation. In this work, the relation between the arc light intensity and welding condition is investigated using heat balance in the Plasma for its possible application to seam tracking in the GMAW process. The arc light intensity is derived to be the function of the arc length and welding current Experiments are carried out to verify the proposed heat balance model. Performances of least square and integration methods to process the signals for seam tracking are compared experimentally. Predicted arc light intensity shows reasonably good agreement with experimental results. The weld seam is successfully tracked through the arc light intensity. The least square and integration methods demonstrate almost same performance of seam tracking with $CO_2$gas shielding.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.3
• /
• pp.19-24
• /
• 2005

Arc Fault Current is an electric discharge which is occurred in two opposite electrode. In this paper, arc current control algorithm is designed for the interruption of arc fault current which is occurred in the local electric network. This arc is one of the main causes of electric fire. Arc fault in electrical network has the characteristics of low current, high impedance and high frequency. Conventional arc current controller does not have the arc current interrupt function. Hence, Controller of arc current is designed for the interruption of arc fault current which has the modified arc characteristics.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.13 no.21
• /
• pp.51-60
• /
• 1990

In this paper we deal with the miniaml cost network flow problem with uncertain arc capacity constraints. When the arc capacities are fuzzy with linear L-R type membership function, using parametric programming procedure, we reduced it to the deterministic minimal cost network flow problem which can be solved by various typical network flow algorithms. A modified Algorithm using the Out-of-kilter algorithm is developed.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.62-68
• /
• 2008

Effects of gravitational orientation on gas tungsten arc welding (GTAW) for 304 stainless steel were studied to determine the critical factors for weld pool formation, such as weld surface deformation and weld pool shape. This study was accomplished through an analytical study of weld pool stability as a function of primary welding parameters (arc current and arc holding time), material properties (surface tension and density), and melting efficiency (cross-sectional area). The stability of weld pool shape and weld surface deformation was confirmed experimentally by changing the welding position. The arc current and translational velocity were the major factors in determining the weld pool stability as a function of the gravitational orientation. A 200A spot GTAW showed a significant variation of the weld pool formation as the arc held longer than 3 seconds, however the weld pool shape and surface morphology for a 165A spot GTAW were 'stable', i.e., constant regardless of the gravitational orientation. The cross-sectional area of the weld (CSA) was one of the critical factors in determining the weld pool stability. The measured CSA ($13.5mm^2$) for the 200A spot GTAW showed a good agreement with the calculated CSA ($14.9mm^2$).

• Journal of Welding and Joining
• /
• v.13 no.1
• /
• pp.115-126
• /
• 1995

Vision sensors using the optical triangulation have been widely used for automatic welding systems in various ways, but their reliability is seriously affected by presence of the arc noise. The reliability of vision sensors was analyzed with variation of the arc noise by considering the reflectance of the base metal. first, the properties of the base metal's reflection were modelled by using the Bidirectional Reflectance-Distribution Function(BRDF), and then the variation of the reflected arc intensity was formulated for various configurations of the torch, base metal, and sensor. The experimental data of the gray level of the reflected arc light were obtained for two materials, mild steel and stainless steel. It was found that the results calculated from the proposed model were in good agreement with the experimental data.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.952-957
• /
• 1992

When the circuit-breaker switches off, an electric arc is established between the contacts. It is very important to understand the arc characteristics for the design of a circuit breaker. This article describes the theoretical analysis of the arc characteristics by means of energy integral method when convection dominated low current arcs are produced in the dual-airflow nozzle of a model interrupter. In order to investigate the arc radius, the average electric field strength and the arc voltage, the arc column is divided into two regions, and then the energy conservation equation is applied to the arc in each region together with the axial cold flow mass flux function, steady-state mass balance equation and Ohm's law. The results show good agreements with those of other researchers.