• Advances in nano research
• /
• 제1권4호
• /
• pp.193-202
• /
• 2013

In this article, we present the effects of Ag doping and after-growth thermal annealing on the photoluminescence (PL) and thermoluminescence (TL) behaviors of $SnO_2$ nanoparticles. $SnO_2$ nanoparticles of 4-7 nm size range containing different Ag contents were synthesized by hydrothermal process. It has been observed that the after-growth thermal annealing process enhances the crystallite size and stabilizes the TL emissions of $SnO_2$ nanostructures. Incorporated Ag probably occupies the interstitial sites of the $SnO_2$ lattice, affecting drastically their emission behaviors on thermal annealing. Both the TL response and dose-linearity of the $SnO_2$ nanoparticles improve on 1.0% Ag doping, and subsequent thermal annealing. However, a higher Ag content causes the formation of Ag clusters, reducing both the TL and PL responses of the nanoparticles.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 학술대회 논문집 일렉트렛트 및 응용기술연구회
• /
• pp.77-81
• /
• 2003

The $Sr_{0.7}Bi_{2.6}Ta_2O_9$(SBT) thin films are deposited on Pt-coated electrode(Pt/$TiO_2/SiO_2$/Si) using RF magnetron sputtering method. The structural and electrical properties of SBT capacitors were influenced with annealing atmosphere. In the XRD pattern, the SBT thin films in all annealed atmosphere had (105) orientation. In the SEM images, Bi-layered perovskite phase was crystallized in all annealing atmosphere and grains largely grew in oxygen annealing atmosphere. The dielectric constant and leakage current density of capacitors annealed oxygen atmosphere are 340 and $2.13{\times}10^{-9}[A/cm^2]$ respectively.

• E2M - 전기 전자와 첨단 소재
• /
• 제16권9호
• /
• pp.62.1-62
• /
• 2003

Silicon oxide with thickness lee than 9 nm is fabricated by tube furnace oxidation. Nitrogen is added to dilute the oxidation rate. Aluminum dots with radius of 0.05 cm are deposited on the oixde. High frequency capacitance-voltage(HF C-V), conductance-voltage(G-V) and current-voltage(I-V) characteristics are measured. Annealing under nitrogen atmosphere is carried out with different time and at different temperature. Densities of the interface states before and after annealing are compared. After annealing, a decrease in density of the interface states is found. Experiments show that 45$0^{\circ}C$ annealing for 30 minutes has the lowest density of the interface states.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.193-195
• /
• 1996

In amorphous transformer core, magnetic field annealing is required for inducing uniaxial magnetic anisotropy to circular direction of the core. Generally annealing temperature is about foot, so insulator using in solenoid bed must have a high temperature stability, mechanical strength and good machinability. In this study, we made the magnetic field annealing apparatus using insulators, conductors, connectors and power supply. And then tested the apparatus in annealing process of 50 kVA amorphous transformers.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.522-527
• /
• 2004

Resealed Simulated Annealing (RSA) has been devised for improving the disadvantage of Simulated Annealing (SA) which require tremendous amount of computation time. RSA and SA have been for optimization of satellite structures and for comparison of results from two algorithms. As a practical application, a satellite structure is optimized by the two algorithms. Weights of satellite upper platform and propulsion module are minimized. MSC/NASTRAN is used for the static and dynamic analysis. The optimization results of the RSA are compared with results of the classical SA. The numbers of optimization iterations could be effectively reduced by the RSA.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.101-107
• /
• 1997

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties was decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the Ax atmospheric gas and the HNx atmospheric gas. As a result of several investigations. We confirmed the following characteristics ; mechanical properties was changed under the influence of the annealing cycle, the heat treatment method and the atmospheric gas. And, elongation in the HNx BAF was better than the Ax BAF. Finally, most important thing in the BAF is using proper annealing cycle in order to get a good quality.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.468-473
• /
• 1993

Damages on Si substrate induced by Ar ion implantation and it annealing behavior during rapid thermal annealing were investigated by the cross-sectional TEM (transmissin electron microscopy), RB(Rutherfordbackscattering) spectra an dthermal wave (TW) modulation reflectance methods. Continuous amorphous layer extending to the surface were generated by Ar ion implantation for higher doses than 1 $\times$1015cm-2. The recrystallization of the amorphous layer prodeeded as the annealing temperature increased . However the amorphous /crystal interfacial undulations caused the micro twins and damage clusters. Damage clusters generated by lower doses than 1 $\times$1015 cm-2 disappeared slowly as the annealing temperature increased, but even at 110$0^{\circ}C$ a few damage clusters still remained.

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2353-2358
• /
• 2017

A femtosecond laser pre-annealing process based on indium zinc oxide (IZO) thin-film transistors (TFTs) is fabricated. We demonstrate a stable pre-annealing process to analyze surface structure change of thin films, and we maintain electrical stability and improve electrical performance. Furthermore, dynamic electrical characteristics of the IZO TFTs were investigated. Femtosecond laser pre-annealing process-based IZO TFTs exhibit a field-effect mobility of $3.75cm^2/Vs$, an $I_{on}/I_{off}$ ratio of $1.77{\times}10^5$, a threshold voltage of 1.13 V, and a subthreshold swing of 1.21 V/dec. And the IZO-based inverter shows a fast switching behavior response. From this study, IZO TFTs from using the femtosecond laser annealing technique were found to strongly affect the electrical performance and charge transport dynamics in electronic devices.

• 한국분말재료학회지
• /
• 제15권1호
• /
• pp.18-22
• /
• 2008

The electromagnetic (EM) wave absorption properties with a variation of crystallization annealing temperature have been investigated in a sheet-type absorber using the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy powder. With increasing the annealing temperature the complex permeability (${\mu}_r$), permittivity (${\varepsilon}_r$) and power absorption changed. The EM wave absorber shows the maximum permeability and permittivity after the annealing at $610^{\circ}C$ for 1 hour, and its calculated power absorption is above 80% of input power in the frequency range over 1.5 GHz.

• 한국분말재료학회지
• /
• 제3권2호
• /
• pp.91-96
• /
• 1996

The effect of vacuum annealing on the oxidation behavior of milled WC-15%Co powder mixture has been studied. A cobalt component in the milled powder mixture was oxidized preferentially above 175$^{\circ}C$ in air. The specimens showed a steady increase in weight at 175$^{\circ}C$ but did constant weight followed by rapid increase in specimen weight at the beginning above 20$0^{\circ}C$. Oxidation of the milled powder mixture was significantly suppressed by vacuum annealing at 30$0^{\circ}C$ for 10 h. Suppression of oxidation by vacuum annealing and different oxidation behaviors of the milled powder mixture between 175$^{\circ}C$ and 20$0^{\circ}C$, were attributed to removal of strain energy stored in the cobalt powder during vacuum annealing or oxidation treatment above 20$0^{\circ}C$. The role of stored strain energy on oxidation of milled WC-15%Co powder mixture was proved by X-ray diffraction method and differential thermal analysis.