• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.897-899
• /
• 2002

BLDCM(Brushless D.C. Motor) is widely used industrial application because of high efficiency and high power density. Especially, In servo system and home appliance, BLDCM is very useful due to high control performance and low acoustic noise. In this paper, 2.5HP rated BLDCM controller and drive was developed for tread mill application. The prototype BLDCM has 4 poles rotor and 24 slots stator. Ferrite was used as a rotor magnet due to the cost and temperature characteristic. For the stable operation of tread mill, over current and high temperature can be detected by the DSP control1er. For the commutation signal, switching patterns from the sensorless circuit and hall sensor signal are used in the DSP controller.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.1
• /
• pp.26-34
• /
• 2008

This study presents an aerodynamic design and an experimental performance test of a turbo air compressor consisted of mixed-flow impeller and curved diffuser for the PEM fuel cell vehicle application. Many studies compare the efficiency, cost or noise level of high-pressure and low-pressure operation of PEM fuel cell systems. Pressure ratio 2.2:1 is considered as design target The goal of compressor design is to enlarge the flow margin of compressor from surge to choke mass flow rate to cover the operational envelope of FCV. Large-scale rig test is performed to evaluate the compressor performance and to compare the effects of compressor exit pipe volume to stall or surge characteristics. The results show that the mixed-flow compressor designed has large flow margin, and the flow margin of compressor configuration with small exit volume is larger than that with large exit volume.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.323-326
• /
• 1999

For decrease the harmonic current components of the power source, a first method is insert the choke coil that used the choke input type rectifier, the booster chopper circuit and buck chopper circuit. And the several method are studying like as the PWM(Pulse Width Modulation) converter and the active filter type which is used the high frequency switching and the sinusoidal wave formed input current. In this type, there are many problem as a low efficiency, increased the noise, the high leakage current and cost up by the high frequency switching. For improve this problems, the partial resonan method is used on the booster inducter and lossles snubber condenser. This method decreased the distortion factor has lower harmonic components than the hard switching and there is no switching loss by the ZCS(Zero Current Switching) at switch turn-on and the ZVS(Zero Voltage Swithcing) at switch turn-off

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.138-141
• /
• 2002

BLDCM(Brushless D.C. Motor) is widely used for industrial application because of high efficiency and high power density Especially, in servo system and home appliance, BLBCM is very useful due to high control performance and low acoustic noise. In this paper, 2.5HP rated BLDCM controller and drive was developed for tread mill application. The prototype BLDCM has 4 poles rotor and 24 slots stator. Ferrite was used as a rotor magnet due to the cost and temperature characteristic. For the stable operation of tread mill, over current and high temperature can be detected by the DSP controller. For the commutation signal, switching patterns from the sensorless circuit and hall sensor signal are used in the DSP controller.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1019-1021
• /
• 2004

BLDCM(Brushless D.C. Motor) is widely used for industrial application because of high efficiency and high power density. Especially, in servo system and home appliance. BLDCM is very useful due to high control performance and low acoustic noise. In this paper, 2.5HP rated BLDCM controller and drive was developed for tread mill application. The prototype BLDCM has 4 poles rotor and 24 slots stator. Ferrite was used as a rotor magnet due to the cost and temperature characteristic. For the stable operation of tread mill. over current and high temperature can be detected by the DSP controller. For the commutation signal, switching patterns from the sensorless circuit and hall sensor signal are used in the DSP controller.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.333-336
• /
• 2009

the equipment increase switching frequency in order to achieve small size, a low noise, and light weight. however, the power switches have high power losses and switching stresses as the switching frequency is increased. In order to solve like this problem point from the present paper it proposed Intese Pulse Light of the half bridge methods which apply the start current circuit which applies the auxiliary equipment. Simulation and experimental result it leads and it brings is more qualitative there is 20% improvement and it confirmed that a possibility of measuring to the patient.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.5
• /
• pp.66-71
• /
• 2012

The capacity criteria have been proposed in order to select a cooperative relay node in WSNs, under the environment where direct path has a poor link gain. This process may ensure the efficiency improvement of signal transfer between source and destination and reduction of energy consumption as well. Two criteria are incorporated to select a cooperative relay node. Firstly, calculate the energy gain ratio between the relay path and the direct path. These are defined as the ratio between the energy factors of 1/g and 1/B. Each stands for an inverse of direct path gain and relay path gain. Secondly, investigate the effects of relay node's usage in WSNs through the simulation in terms of energy consumption. In conclusion, using a selected cooperative relay node based on the selected criteria is effective in terms of both energy efficiency and capacity of WSNs especially when direct path gain is relatively low.

• Electronics and Telecommunications Trends
• /
• v.35 no.4
• /
• pp.21-33
• /
• 2020

Single photon detector technologies have emerged as powerful tools in optical quantum information applications such as quantum communication, quantum information, and integrated quantum photonics. Owing to significant attempts in the previous decade at improving photon-counting detectors, several single photon detectors with high efficiency and low noise have been realized within the optical wavelength regime. In this paper, we provide an overview of current studies on single photon detectors operating at wavelengths from the ultraviolet to the infrared. In addition, we discuss applications of single photon detector technologies in quantum communication and integrated quantum photonics.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.139-142
• /
• 1999

Screw rotors are core parts of screw type air compressors, compressors in refrigerating machines and super chargers of automobiles etc. They are composed of a female and a male rotors which have complex section profiles and helically swept geometry. Screw type compressors have advantages of low noise, high efficiency, less needs in maintenance etc. Usually, machining process of screw rotors requires long machining time using CNC machine designed only for screw rotors, which increase the cost of production. In this work, the screw rotors for air-compressors were manufactured with fiber reinforced epoxy composite materials by resin transfer molding process. The mold for the RTM process was made of aluminum and silicon rubber and was designed for release of helical shape products. Composite screw rotors, manufactured by RTM process, have advantages of lightweight, less cost of production, good characteristics of vibration etc.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.824-827
• /
• 2003

Recently, Development of Rare Earth Permanent magnet with the high remanence, high coercivity allow the design of brushless motors with very high efficiency over a wide speed range. Cogging torque is produced in a permanent magnet by magnetic attraction between the rotor mounted permanent magnet and the stator teeth. It is an undesired effect that contributes to the machines output ripple, vibration, and noise. This cogging torque can be reduced by variation of magnet arc length, airgap length, magnet thickness, shifting the magnetic pole and varying the radial shoe depth and etc. In this paper, Some airgap length and magnet arc that reduce cogging torque are found by FEM(Finite element method). The SPM type of high-capacity BLDC motor is optimized as a sample model.