• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.8
• /
• pp.742-747
• /
• 2012

A modified NDIF method using a sub-domain approach is introduced to extract highly accurate eigenvalues of two-dimensional, arbitrarily shaped acoustic cavities. The NDIF method, which was developed by the authors for the eigen-mode analysis of arbitrarily shaped acoustic cavities, has the feature that it yields highly accurate eigenvalues compared with other analytical methods or numerical methods(FEM and BEM). However, the NDIF method has the weak point that it can be applicable for only convex cavities. It was revealed that the solution of the NDIF method is very inaccurate or is not suitable for concave cavities. To overcome the weak point, the paper proposes the sub-domain method of dividing a concave domain into several convex domains. Finally, the validity of the proposed method is verified in two case studies, which indicate that eigenvalues obtained by the proposed method are more accurate compared to the exact method, the NDIF method, or FEM(ANSYS).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.8
• /
• pp.1833-1841
• /
• 1997

Rectangular dielectric waveguides, the most fundamental and indispensible elements in integrated optics, have been investigated by many researchers with various approaching methods including from the relatively approximate techniques to the numerical method. In this paper, the optimum equivalent waveguide model is adopted which is determined by a perturbation feedback process for analyzing the propagation constant by means of computer simulation, we have ascertained that the propagation constant from perturbation feedback method gives the best approximate value because it coincide with more exact value than obtained by other approximating methods. The technique also provides analytical expression for the modal field profile that should be useful in the design of various integrated optical devices.

• Explosives and Blasting
• /
• v.36 no.3
• /
• pp.10-18
• /
• 2018

The dynamic behaviour of the rock mass under the dynamic load is different from the static application of the maximum load of the same size. An experimental approach to investigating rock behavior under dynamic loads is more difficult than that under static conditions in control of dynamic loads, measurement and analysis of the results. Numerical methods are less constrained by performing the experiments numerically, rather than experimental ones, so they can be very powerful analytical tool at the design stage. However, even if the algorithms of the analysis method are appropriate, careful analysis is required because the calculation results may vary largely depending on input data and boundary conditions. In this paper, when investigating the behavior of rock structures under dynamic load numerically, the effects of boundary conditions, dynamic load and calculation time step, and dynamic load characteristics on the calculation results were reviewed to provide guidance on setting up boundary conditions and calculation time step related to dynamic analysis.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.1 no.1
• /
• pp.71-80
• /
• 1989

In this paper, the concept of the infinite element is applied to the linear wave diffraction and radiation problems. The hydrodynamic pressure forces are assumed to be inertially dominated, and viscous effects are neglected. The near field region surrounding the solid body is modelled using the conventional finite elements, and the far field region is represented using the infinite elements .In order to represent the scattered wave potentials in the far field region more accurately, the infinite elements are developed using special shape functions derived from the asymptotic expressions for the analytical eigenseries solution of the scattered waves. The system matrices of the infinite elements are constructed by performing the integration in the infinite direction analytically to achieve computational efficiency. Numerical analyses are carried out for vertical axisymmetric bodies to validate the infinite elements developed here. Comparisons with the results by other available numerical solution methods show that the present method using the infinite elements gives fairly good results. Numerical experiments are per-formed to determine the suitable location of the infinite elements and the appropriate size of the finite elements which directly affect accuracy and efficiency of the solution.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.541-550
• /
• 2012

An improved method of moments using a hybrid Galerkin-interpolation technique for numerical analysis of electromagnetic wave scattering in the 3-dimensional space is presented in this paper. Basically, the EFIE(electric field integral equation) and RWG(Rao-Wilton-Glisson) basis function are used to compute a property of electromagnetic wave scattering. We propose a hybrid technique combining the existing Galerkin's method with the interpolation method to improve the efficiency of the numerical computation. Then, an index of relative distance of each cells was defined to distinguish the relatively far elements, which interpolation method can be applied. To verify the performance of the proposed technique, the analytical Mie-series solution was used to compute the theoretical RCS of a conducting sphere for the purpose of comparison. We also applied this hybrid technique to various scatterers such as trihedral/omni-directional corner-reflectors to analyze the radar backscattering properties.

• Journal of Mechanical Science and Technology
• /
• v.17 no.8
• /
• pp.1148-1155
• /
• 2003

The finite element method is one of the methods widely applied for predicting vibration in mechanical structures. In this paper, the effect of the mesh size of the finite element model on the accuracy of the numerical solutions of the structural vibration problems is investigated with particular focus on obtaining the optimal mesh size with respect to the solution accuracy and computational cost. The vibration response parameters of the natural frequency, modal density, and driving point mobility are discussed. For accurate driving point mobility calculation, the decay method is employed to experimentally determine the internal damping. A uniform plate simply supported at four corners is examined in detail, in which the response parameters are calculated by constructing finite element models with different mesh sizes. The accuracy of the finite element solutions of these parameters is evaluated by comparing with the analytical results as well as estimations based on the statistical energy analysis, or if not available, by testing the numerical convergence. As the mesh size becomes smaller than one quarter of the wavelength of the highest frequency of interest, the solution accuracy improvement is found to be negligible, while the computational cost rapidly increases. For mechanical structures, the finite element analysis with the mesh size of the order of quarter wavelength, combined with the use of the decay method for obtaining internal damping, is found to provide satisfactory predictions for vibration responses.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.7-14
• /
• 2010

In order to analyze the vibro-impacts in the torsional system, several clearance types of nonlinearities should be included with the analytical or numerical method. These kinds of nonlinear factors can cause the errors while the system is calculated specifically with the numerical method, also it might take too long to get right answers with the every nonlinearity in the original system. Therefore, there are several methods developed for the sake of overcoming the deficiency of the analysis with the original system and saving the calculating time. The original system can be reduced by keeping the system characteristics such as from 14 to 6 DOF. Especially, since the torque flow in the torsional system is connected with the specific gear ratios, the original system can be transferred into the simpler system corresponding to each gear ratio rather than the original system, which can also show the same system characteristics such as the natural frequencies and the mode shapes. By using the reduced system, the calculating time can be saved and the redundant nonlinear effects for the system analysis can be ignored without any numerical errors.

• Computational Structural Engineering
• /
• v.10 no.3
• /
• pp.217-223
• /
• 1997

This paper deals with the basic concepts of sensitivity analysis in a time domain for the transient response of a lumped mass system. Sensitivity analysis methods in thme domain for determining the effects of parameter changes on the response of a dynamic system by external excitation are presented. The parametric sensitivity of a lumped mass system in time domain can be investigated using different types of sensitivity functions, including first order standard and percentage sensitivity functions. These sensitivity functions are determined as a function of partial derivatives of system variables taken with respect to system parameters. In addition, we compared the results of the analytical method by direct method and those of numerical methods.

• Steel and Composite Structures
• /
• v.20 no.3
• /
• pp.623-649
• /
• 2016

Most of the early studies on plates vibration are focused on two-dimensional theories, these theories reduce the dimensions of problems from three to two by introducing some assumptions in mathematical modeling leading to simpler expressions and derivation of solutions. However, these simplifications inherently bring errors and therefore may lead to unreliable results for relatively thick plates. The main objective of this research paper is to present 3-D elasticity solution for free vibration analysis of continuously graded carbon nanotube-reinforced (CGCNTR) rectangular plates resting on two-parameter elastic foundations. The volume fractions of oriented, straight single-walled carbon nanotubes (SWCNTs) are assumed to be graded in the thickness direction. In this study, an equivalent continuum model based on the Eshelby-Mori-Tanaka approach is employed to estimate the effective constitutive law of the elastic isotropic medium (matrix) with oriented, straight carbon nanotubes (CNTs). The proposed rectangular plates have two opposite edges simply supported, while all possible combinations of free, simply supported and clamped boundary conditions are applied to the other two edges. The formulations are based on the three-dimensional elasticity theory. A semi-analytical approach composed of differential quadrature method (DQM) and series solution is adopted to solve the equations of motion. The fast rate of convergence of the method is demonstrated and comparison studies are carried out to establish its very high accuracy and versatility. The 2-D differential quadrature method as an efficient and accurate numerical tool is used to discretize the governing equations and to implement the boundary conditions. The convergence of the method is demonstrated and to validate the results, comparisons are made between the present results and results reported by well-known references for special cases treated before, have confirmed accuracy and efficiency of the present approach. The novelty of the present work is to exploit Eshelby-Mori-Tanaka approach in order to reveal the impacts of the volume fractions of oriented CNTs, different CNTs distributions, various coefficients of foundation and different combinations of free, simply supported and clamped boundary conditions on the vibrational characteristics of CGCNTR rectangular plates. The new results can be used as benchmark solutions for future researches.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.107-115
• /
• 2001

It is required more precise analysis for practical load because of complexities and varieties of vehicle structure. To establish the numerical model, many researchers have been developed designing tools for linking F.E. Analysis results and experimental results. There studies have generally focused on each experimental method or analytical method separately. There are few studies based on both methods. This paper conceives new procedure for the determination of the load direction and magnitude applied on mechanical structures. New procedure is the combination of the analytical and empirical method with analyzed strain by F.E. Analysis under unit load and with measured principal stress by strain gages under driving load, respectively. In this paper, we theorize the procedure of practical load determination and make the validity and the practicality of the procedure with the application to T-shape jointed structure. F.E. Analysis is conducted to get the principal stress on arbitrary points in the F.E. model of T-shape joint under unit load. Then experiment is carried out to get the principal stress on the same points of F.E. model. To demonstrate the actual driving condition, the load conditions are bending and torsion. From these two data sets, the magnitude, the direction and the position of load can be obtained. Theory and practice do not always coincide; since there are some errors such as ill-poseness, measuring error and modeling error in experimental data, we examine the proper method of error minimization.