• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.99-99
• /
• 2009

Two different micro-flows during the evaporation of ink droplets were achieved by engineering both surface tension gradient and compositional gradient across the ink droplet: (1) Coffee-ring generating flow resulting from the outward flow inside the ink droplet & (2) Marangoni flow leading to the circulation flow inside the ink droplet. The surface tension gradient and the compositional gradient in the ink droplets were tailored by mixing two different solvents with difference surface tension and boiling point. In order to create the coffee-ring generating flow (outward flow), a single-solvent system using N,N-dimethylformamide with nano-sized spherical alumina particles was formulated, Marangoni flow (circulation flow) was created in the ink droplets by combining N,N-dimethylformamide and fotmamide with the spherical alumina powders as a co-solvent ink system. We have investigated the effect of these two different flows on the formation of ceramic films by inkjet printing method, The packing density of the ceramic films printed with two different ink systems (single- and co-solvent systems) and their surface roughness were characterized. The dielectric properties of these inkjet-printed ceramic films such as dielectric constant and dissipation factor were also studied in order to evaluate the feasibility of their application to the electronic ceramic package substrate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.171-172
• /
• 2008

$(Ba_{0.57}Sr_{0.33}Ca_{0.10})TiO_3$ (BSCT) thick films doped with 0.1 mol% $MnCO_3$ and $Yb_2O_3$ ($0.1{\sim}0.7$ mol%) were fabricated by the screen printing method on the alumina substrate. And the structural and electrical properties as a function of $Yb_2O_3$ amount were investigated. The lattice constants of the BSCT thick film doped with 0.1 mol% is 0.3955 nm. The specimen doped with 0.7 mol% $Yb_2O_3$ showed dense and uniform grains with diameters of about 6.3 mm. The thickness of all BSCT thick films was approximately 60 mm. The Curie temperature of the BSCT specimen doped with 0.1 mol% $Yb_2O_3$ was $18^{\circ}C$, and the dielectric constantand dielectric loss at this temperature was 4637 and 4.2%, respectively. The BSCT specimen doped with 0.1 mol% $Yb_2O_3$ showed the maximum value of $349{\times}10^{-9}C/cm^2K$ at Curie temperature. The figure of merit $F_D$ for specific detectivity of the specimens doped with 0.1 mol% $Yb_2O_3$ showed the highest value of $10.9{\times}10^{-9}Ccm/J$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.31-34
• /
• 2003

($Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3$ (BSCT) (x=0.10, 0.15, 0.20) powder, prepared by the sol-gel method, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen-printing techniques on alumina substrates using the BSCT paste. The structural and the electrical properties were investigated for various composition ratio and sintering temperature. BSCT thick film thickness, obtained by four printings, was approximately 110 ~ 120 ${\mu}m$. The Curie temperature and dielectric constant at room temperature were decreased with increasing Ca content. The relative dielectric constant, dielectric loss and tunability of the BSCT(50/40/10) specimen, which was sintered at $1420^{\circ}C$ and measured at 1MHz, were about 910, 0.46% and 9.28% at 5kV/cm, respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.359-361
• /
• 2003

Nano-porous alumina was investigated as a protecting layer in an AC Plasma Display Panel. A 2 ${\mu}m$ thick nano-porous $Al_2O_3$ layer inserted with MgO was formed on the dielectric layer instead of the conventional 500 nm-thick MgO thin film. Both nano-porous $Al_2O_3$layer and inserted MgO were prepared by wet process. The luminance and luminous efficiency of 3-inch test panel adopting nano-porous $Al_2O_3$ was higher than that of the conventional PDP.

• 한국전기전자재료학회논문지
• /
• 제19권12호
• /
• pp.1092-1098
• /
• 2006

The influence of the concentration of precursor solution and the number of solution coatings on the densification of the $Pb(Zr_xTi_{1-x})O_3$ (PZT) thick films was studied. PZT powder and PZT precursor solution were prepared by3 sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The composition of powder and precursor solution were PZT(70/30) and PZT(30/70), respectively. The PZT precursor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5 to 2.0 mol/L[M] and the number of coating was repeated from 0 to 6. The XRD patterns of all PZT thick films shelved typical perovskite polycrystalline structure. The porosity of the thick films was decreased with increasing the number of coatings and 6-time coated films with 1.5 M showed the dense microstructure and thickness of about $60{\mu}m$. The relative dielectric constant of the PZT thick film was increased with increasing the number of solution coatings and the thick films with 1.5 M, 6-time coated showed the 698. The remanent polarization the 1.5 M and 6-time coated PZT thick films was $38.3{\mu}C/cm^2$.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.441-446
• /
• 2009

Dense crack-free yttria film with 10 $\mu m$ thickness was prepared on aluminum by aerosol deposition. X-ray diffraction pattern on the film showed that it contained the same crystalline phase as the raw powder. Transmission electron microscopy revealed a nanostructured yttria film with grains smaller than 100 nm. Tensile adhesion strength between the film and aluminum substrate was 57.8 $\pm$ 6.3MPa. According to the etching test with $CF_4-O_2$ plasma, the etching rate of the yttria film was 1/100 that of quartz, 1/10 that of sintered alumina and comparable to that of sintered yttria.

• 센서학회지
• /
• 제23권3호
• /
• pp.170-172
• /
• 2014

$CO_2$ sensor was used only one solid electrolyte in many cases. To improve the sensing characteristics of $CO_2$ sensors, solid electrolyte $CO_2$ sensor has been developed by bi-electrolyte type sensor using Na-Beta-alumina and YSZ. However, in many further studies, bi-electrolyte type sensor was made by pellet pressed by press machine and additional treatment for formation of interface. In the aspect of mass production, using thick film and additional treatment is not suitable. In this study, $CO_2$ sensor was fabricated by bi-electrolyte structure which was made by an NBA paste layer deposited on YSZ pellet and fired at $1650^{\circ}C$ for 2 hour. The formation of stable interface between YSZ and NBA were confirmed by SEM image. When the type IV electrochemical cell arrangement represented by $CO_2,O_2,Pt{\mid}Li_2CO_3-CaCO_3{\parallel}NBA{\parallel}YSZ{\mid}O_2,Pt$ is used to measure the $CO_2$ concentration in air. This sensor EMF should depend only on the concentration of $CO_2$ by logarithmic. Also, sensor shows $P_{CO_2}$ and EMF relationship like nerstian reaction at a temperature of $450^{\circ}C$.

• 센서학회지
• /
• 제15권3호
• /
• pp.168-172
• /
• 2006

Potentiometric $CO_{2}$ sensors were fabricated using a NASICON ($Na_{1+x}Zr_{2}Si_{X}P_{3-X}O_{12}$, 1.8 < x < 2.4) thick film and auxiliary layers. The powder of a precursor of NASICON with high purity was synthesized by a sol-gel method. By using the NASICON paste, an electrolyte was prepared on the alumina substrate by screen printing and then sintered at $1000^{\circ}C$ for 4 h. A series of $Na_{2}CO_{3}-CaCO_{3}$ auxiliary phases were deposited on the Pt sensing electrode. The electromotive force (emf) values were linearly dependent on the logarithm of $CO_{2}$ concentration in the range between 1,000 and 10,000 ppm. The device attached with $Na_{2}CO_{3}-CaCO_{3}$ (1:2 in mol.%) showed good sensing properties in the low temperatures.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.151-155
• /
• 2003

The requirements for harsh environment electronic controllers in automotive applications have been steadily becoming more and more stringent. Electronic substrate technologists have been responding to this challenge effectively in an effort to meet the performance, reliability and cost requirements. An effect of the plasma cleaning at the alumina substrate and the IMC layer between $Sn-37wt\%Pb$ solder and Ag-Pd thick film conductor after reflow soldering has been studied. Organic residual carbon layer was removed by the substrate plasma cleaning. So the interfacial adhesive strength was enhanced. As a result of AFM measurement, Ag-Pd conductor pad roughness were increased from 304nm to 330nm. $Cu_6Sn_5$ formed during initial ref]ow process at the interface between TiWN/Cu UBM and solder grew by the succeeding reflow process so the grains had a large diameter and dense interval. A cellular-shaped $Ag_3Sn$ was observed at the interface between Ag-Pd conductor pad and solder. The diameters of the $Ag_3Sn$ grains ranged from about $0.1\~0.6{\mu}m$. And a needle-shaped $Ag_3Sn$ was also observed at the inside of the solder.

• 대한전자공학회논문지
• /
• 제8권5호
• /
• pp.10-19
• /
• 1971

음성 전단증폭기를 후막집적회로기술을 이용하여 집적회로화하는데에 파생되는 여러가지 기술적인 문제를 실제로 연구개발을 실시한 경험을 토대로 소개하였다. 특히 전자계산기를 이용한 회로해석을 통하여 전단증폭기의 성능을 가장 민감하게 좌우하는 저항소자를 찾아 내므로써 크기의 아루미나 기판상에 집적된 7개의 저항중에서 한개만을 조정하여도 원하는 주파수특성을 얻을 수 있음을 확인하였다. 이로써 7개의 저항을 설계치에 맞게 각각 조정하는 작업을 하지 않고 그 중 하나만을 원하는 특성이 나타날때까지 조정하는 기능조정방법을 찾아내어 조정작업에 소요되는 인건비를 1/7로 절감할 수 있도록 하였다. 이 외에도 저항체와 도체간의 접촉문제라든가, 크로쓰오바의 기생용량문계 또는 저항조정방법에 따르는 잡음도의 변화문제에 대해서도 상세히 다루었다.