• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 B
• /
• pp.1243-1247
• /
• 1996

In this paper, a small PLC system is designed and developed for the distributed building control and fire control system. It uses 8031, a 8-bit micro controller from Intel Inc. The size of the PLC is $7cm{\times}8cm$ and the PLC can accept 4 sensor inputs and drive 4 relay outputs, which operates at 24V. Multiple access of PLC by one host computer is implemented by assigning a unique 10 to each PLC, which ranges from 0 to 126. The operation starts by sending a command packet from host computer to a PLC and the PLC of the same 10 fetches the command packet by comparing the first byte of the command packet with its own 10. The PLC is programmed to perform a various functions and the function is selected by the content of the command byte, which is the second byte of the command packet. The third byte, which is the last byte, is a checksum byte. The checksum byte is the sum of the first byte and the second byte and is used to detect the communication error. Depending on the content of the command byte, PLC performs the desired function and returns the response packet back to the host computer. The response packet is also a three-byte packet, 10 byte, response byte and checksum byte. For the independent operation of PLC without being controlled by the host computer, variable length RULE data packet is sent to PLC. In case the communication line is broken, the PLC perform the independent operation by referencing the RULE data. The applicable areas are; building automation system, distributed factory automation, measurement of temperature of toxic or dangerous area.

• 센서학회지
• /
• 제24권2호
• /
• pp.113-118
• /
• 2015

Intravenous (IV) infusion set is one of the most common treatment methods applied to hospitalized patients. However, it is necessary to check the injection of IV solution in order to prevent patients from any possible medical injuries. In this paper, using the optical sensors to detect exhaustion of IV solution was proposed. The optical sensor is coplanar structure composed of LED and photodiode which is installed according to focal distance of the lens. These two elements detect exhaustion of IV solution at the desired point conveniently. Through the results of experiments using various wavelength of LED (R.G.B), the blue LED was selected to the optimum light source. The suggested optical sensor can detect exhaustion of IV solution by the differences in the amount of light which is caused by properties such as total reflection, refractive index and scattering. From the implementation, the detector is applicable to both containers of IV solution, glass bottle and plastic pack. And also the result shows apparent differences according to existence of IV solution even if the IV solution color and illumination were changed.

• Journal of Microbiology and Biotechnology
• /
• 제24권3호
• /
• pp.421-426
• /
• 2014

To characterize the extended-spectrum beta-lactamases (ESBLs) in diarrheagenic Escherichia coli from Korea in 2008-2011, we screened seven enterotoxigenic E. coli (ETEC) and one enteroaggregative E. coli (EAEC) that produce ESBLs from a nationwide survey. All eight isolates produced CTX-M-type ESBLs, including CTX-M-12 (n = 4), CTX-M-14 (n = 2), and CTX-M-15 (n = 2). PCR-based replicon typing indicated that the $bla_{CTX-M-12}$ genes of four ETEC isolates were carried on a conjugative IncF plasmid, whereas the $bla_{CTX-M-14}$ of one EAEC was located on an IncK plasmid. This is the first report of the occurrence of $bla_{CTX-M}$ genes in clinical isolates of EAEC in Korea. The ESBL-producing isolates were shown to be different based on pulsed-field gel electrophoresis and multilocus sequence typing, whereas the four isolates with CTX-M-12 were clonally related. These observations raise an alarm for the spread of plasmid-mediated resistance to ESBL among diarrheagenic E. coli.

• Reproductive and Developmental Biology
• /
• 제33권3호
• /
• pp.139-146
• /
• 2009

This study tried to develop the system (device) that automatically notify a manager of condition just before and after farrowing to extend ubiquitous-based technology and to increase efficiency of delivery care and productivity by reducing human labor and time on standby when farrowing management is done in the difficult and hard working environment of farrowing such as night or holidays in field sand especially in pig industry. In this test, selected 10 gilts were executed timed artificial insemination and were set up each temperature sensor and load sensor to them 3 days before the estimated farrowing day and were observed the farrowing situation. This study was embodied the NESPOT-based (KT Corporation) monitoring system, the system to transmit data in real time by utilization of wireless LAN and the sensor module to apply the ubiquitous environment to them. And this study was observed the situation to automatically notify situations of 10 gilts that first bore just before and after farrowing. The result obtained the farrowing situations of them in real time by setup of the NESPOT-based monitoring system to check farrowing situation directly is as follow. The average time of the automatic notice about situation just before farrowing by the temperature sensor was 27.5 minutes before the beginning of farrowing (the expulsion time of a piglet). 6 of 8 pregnant gilts that first bore automatically were notified situations just before farrowing and the temperature sensors inserted into 2 ones before farrowing were omitted. (The automatic notice rate 75%) The average time of the automatic notice of situation just after farrowing by the load sensor was taken 46.5 minutes after the beginning of farrowing (the expulsion time of a first piglet). The average gestation period of 8 ones that first bore and were tested by the automatic notice of farrowing situation was 115.6 days. This result found that the automatic farrowing notice system by the temperature sensor is more efficient than the load sensor as the automatic farrowing alarm device and sanitary treatment and improvement of the omission rate were required.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.605-610
• /
• 2011

간척지나 해안지역과 같은 연약지반에 건축 및 토목공사를 위해서는 지반의 강도를 높이기 위한 연약지반개량공사가 필수적이다. 연약지반 개량 공법은 여러 가지가 있으나 우리나라를 비롯해 세계적으로 연직배수공법을 주로 사용하고 있다. 연직배수공법은 연약한 점성토 지반 내에 인공적으로 연직 배수재를 다수 설치하여 배수거리를 단축시킴으로써 압밀을 촉진시키고, 그에 따른 강도증가 효과를 얻을 수 있는 공법이다. 연직배수재로는 경제성과 시공성이 우수한 PBD가 널리 사용되고 있다. PBD 시공품질은 시공 깊이, 압력, 수직도 등에 영향을 받게 된다. 본 논문에서는 PBD 시공시 배수재의 시공 심도, 압력, 수직도를 자동측정하여 작업자가 실시간으로 모니터링 할 수 있고 시공결과를 자동 저장하는 시스템을 개발하였다. 개발된 시스템은 시공 불량 요인이 발생시 자동 경고하여 불량률을 줄일 수 있고, 장비의 이상 발생시 자동 제어시스템을 가동하여 작업의 안전성을 확보하도록 하였다.

• 한국안전학회지
• /
• 제26권4호
• /
• pp.34-40
• /
• 2011

This paper is purposed to develop an leakage current detecting system(LCDS) which can prevent electrical fires on breaker capacity expansion as well as ruptures of XL(Extra long) pipelines and power failure by operation of ELB(Earth leakage breaker) at auto water machine in winter. In order to develop LCDS, this paper studied field state investigation, field state experiment, development of leakage alarm system and verification experiments. Field states investigation at livestock companies(10 companies) in cheong-won location to deduce the problems of auto water machine is analyzed. The field state experiment is conducted at B livestock company in cheong won location. The field state experiment method is measured with leakage current when ELB tripped by environment factor(fine, cloudy, and rainy day). The LCDS is developed as MCU(Micro Control Unit) part applied leakage current values at B livestock company. Verification experiments for the leakage current detecting system were conducted by two methods of current supply and field test. Results show that LCDS suggested in this paper are valuable and usable in auto water machine based on environment factor, which will prevent severe damage to human beings and properties and reduce the electrical fires in livestock.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2006년도 춘계종합학술대회
• /
• pp.247-250
• /
• 2006

현재 고밀도 반도체제작 환경에서는 Reactive ion Etching (RIE) 과정에서의 생산성을 극대화하기 위해서 비이상적인 공정장비를 발견하는 것이 매우 중요하다. 생산과정에서 오류발견의 중요성을 설명하기 위해 Support Vector Machine (SVM)은 실시간으로 공정오류에 대한 판단에 대한 도움을 주기 위해 사용되었다. baseline run으로부터 얻은 데이터로 SVM 모델을 구성하고 정상인 run 데이터와 비정상 run 데이터로 SVM 모델을 검증한다. 통계적 공정제어에서 흔히 이용되는 control limits를 도입하여 정상데이터가 내재하고 있는 램덤 변화율이 반영된 SVM 모델 기반의 control limits를 수립하고, 그 control limits를 바탕으로 오류발견을 실행한다. SVM을 이용함으로써 RIE의 오류발견은 run to run 기반에 정상인 run데이터는 0% 오류율이 증명되었다.

• 한국군사과학기술학회지
• /
• 제17권1호
• /
• pp.90-95
• /
• 2014

The system design and the system performance analysis of 3D imaging laser radar system for the mapping purpose is addressed in this article. For the mapping, a push-bloom scanning method is utilized. The pulsed fiber laser with high pulse energy and high pulse repetition rate is used for the light source of laser radar system. The high sensitive linear mode InGaAs avalanche photo-diode is used for the laser receiver module. The time-of-flight of laser pulse from the laser to the receiver is calculated by using high speed FPGA based signal processing board. To reduce the walk error of laser pulse regardless of the intensity differences between pulses, the time of flight is measured from peak to peak of laser pulses. To get 3D image with a single pixel detector, Risley scanner which stirs the laser beam in an ellipsoidal pattern is used. The system laser energy budget characteristics is modeled using LADAR equation, from which the system performances such as the pulse detection probability, false alarm and etc. are analyzed and predicted. The test results of the system performances are acquired and compared with the predicted system performance. According to test results, all the system requirements are satisfied. The 3D image which was acquired by using the laser radar system is also presented in this article.

• 한국정보통신학회논문지
• /
• 제22권10호
• /
• pp.1386-1391
• /
• 2018

이동하는 플랫폼에 탑재된 레이더는 주엽으로 수신되는 주엽 클러터 신호와 더불어 부엽에서 수신되는 고도 클러터에 의해서 표적 신호가 간섭을 받는다. 고도 클러터는 거리가 주엽 클러터에 비해 비교적 짧기 때문에 강한 신호로 레이더에 유입된다. 이러한 클러터는 레이더의 오보 확률을 높이는 주 원인으로 주엽 클러터와 고도 클러터 신호를 동시에 억제할 수 있는 기술이 요구된다. 본 논문에서는 이동 플랫폼 레이더에서 발생하는 주엽 클러터와 고도 클러터 신호를 제거하기 위해서 2개의 펄스 제거기(pulse canceller) 구조를 사용하는 클러터 억제 방법을 제시한다. 펄스 제거기를 사용함에 따른 수신신호의 상관도를 분석하고 두 영역의 클러터를 억제하기 위해서 상관도가 고려된 staggered 펄스 제거기 구조를 보인다. 마지막으로 시뮬레이션을 통해 두 개의 주파수군에 형성된 고도 클러터와 주엽 클러터 성분들이 제안된 staggered 펄스 제거기를 통해 제거되는 것을 보인다.

• 정보과학회 논문지
• /
• 제43권1호
• /
• pp.119-125
• /
• 2016

인지 무선 기술은 보조 사용자가 (SUs) 주 사용자 (PUs)에 간섭을 주지 않고 기회주의적 방식으로 라이선스 스펙트럼을 사용할 수 있는 기술이다. 인지 라디오의 핵심 기술은 스펙트럼 센싱이다. 그러나 인지 무선 센서 네트워크에서 에너지 효율적인 스펙트럼 센싱 기법에 대한 연구는 많지 않다. 본 논문에서는 클러스터 기반의 인지 무선 센서 네트워크를 위한 에너지 효율적인 협력 스펙트럼 센싱 노드 선택 기법을 제안한다. 제안하는 기법에서, 허위 경보 확률 및 에너지 소비를 최적화하기 위하여 클러스터 내 스펙트럼 센싱 노드들의 수를 최소화하게 된다. 시뮬레이션 결과를 통하여 본 논문에서 제안한 최적의 스펙트럼 센싱 노드 수를 적용하므로 스펙트럼 센싱 효율성이 향상되었고, 또한 네트워크의 에너지 효율성도 보장된 것을 검증하였다.