• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.777-785
• /
• 2021

Many utility lines are buried underground to provide various functions of the city. Because historical records are not managed systematically, damage has occurred during excavation. In addition, the demand for an underground facility management system is increasing as the aerial underground project is progressing. By attaching an electronic recognition sensor to an underground facility, such as pipelines, the management history and site conditions can be carefully managed. Therefore, in this study, electronic recognition sensors, such as BLE Beacon, UHF RFID, geomagnetic sensor, and commercial marker, were tested to analyze the strengths, weaknesses, and field applicability through a pilot project. According to the limited research results collected through two pilot projects, the installation depth is most important to demonstrate the performance of the electronic reader. In addition, because it should be used in urban areas, the influence of environmental interference should be minimized, and there should be no performance degradation over time. In the case of the geomagnetic recognizer, the effect of environmental interference was large, and performance degradation occurred over time using the BLE Beacon. In the field situation, where the installation depth can be controlled to less than 40cm, the utility of the battery-free UHF RFID was the best.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.231-236
• /
• 2021

The Aphid, Myzus persicae, and the bean bug, Riptortus clavatus, are major insects in crops. This study examined the insecticide susceptibility and phytotoxicity of insecticides dispersed using an Unmanned Aerial Vehicle (UAV, multi-copter) against the insects. Sulfoxaflor suspension concentrate (SC, 16X) on potato fields and etofenprox, methoxyfenzide suspo-emulsion(SE, 8X) on soybean fields were dispersed after deploying water-sensitive paper within the field to measure the distribution pattern and coverage index of the falling insecticide. Both insecticides showed a controlled mortality of 76.4% against aphids and 97.5% and 94.4% against the 2nd nymphal, and 5th nymphal stage of the bugs, respectively. The droplet distribution was less than 0.5mm, and coverage analysis revealed an inside and outside coverage of 3.1 and 1.6, respectively. The surrounding area was affected by insecticide spraying using a multi-copter. This study is expected to help expand UAV control and use it safely in the future.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.2
• /
• pp.107-120
• /
• 2021

Electric-powered distributed propulsion aircraft possess a complex wake flow and mutual interference with the airframe, due to the use of many propellers. Accordingly, in the early design stage, rapid aerodynamic and load analysis considering the effect of propellers for various configurations and flight conditions are required. In this study, an efficient panel-based aerodynamic analysis method that can take into account the propeller effects is developed and validated. The induced velocity field in the region of propeller wake is calculated based on Actuator Disk Theory (ADT) and is considered as the boundary condition at the vehicle's surface in the three-dimensional steady source-doublet panel method. Analyses are carried out by selecting an isolated propeller of the Korea Aerospace Research Institute (KARI)'s Quad Tilt Propeller (QTP) aircraft and the propeller-wing configuration of the former experimental study as benchmark problems. Through comparisons with the results of computational fluid dynamics (CFD) based on actuator methods, the wake velocity of propeller and the changes in the aerodynamic load distribution of the wing due to the propeller operation are validated. The method is applied to the analysis of the Optional Piloted Personal Aerial Vehicle (OPPAV) and QTP, and the practicality and validity of the method are confirmed through comparison and analysis of the computational time and results with CFD.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.361-370
• /
• 2021

Carbon fiber reinforced polymer (CFRP) is one of the composite materials, which has a unique property that is lightweight but strong. The CFRPs are widely used in various industries where their unique characteristics are required. In particular, electric and unmanned aerial vehicles critically need lightweight parts and bodies with sufficient mechanical strengths. Vehicles using the battery as a power source should simultaneously meet two requirements that the battery has to be safely protected. The vehicle should be light of increasing the mileage. The CFRP has considered as the one that satisfies the requirements and is widely used as battery housing and other vehicle parts. On the other hand, in the battery area, carbon fibers are intensively tested as battery components such as electrodes and/or current collectors. Furthermore, using carbon fibers as both structure reinforcements and battery components to build a structural battery is intensively investigated in Sweden and the USA. This mini-review encompasses recent research trends that cover the classification of structural batteries in terms of functionality of carbon fibers and issues and efforts in the battery and discusses the prospect of structural batteries.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.24 no.2
• /
• pp.52-63
• /
• 2021

In previous research, the coastal wetlands were detected by using the vegetation indices or land cover classification maps derived from the multispectral bands of the satellite or aerial imagery, and this approach caused the various limitations for detecting the coastal wetlands with high accuracy due to the difficulty of acquiring both land cover and topographic information by using the single remote sensing data. This research suggested the efficient methodology for detecting the coastal wetlands using the sentinel-2 satellite image and SRTM(Shuttle Radar Topography Mission) DEM (Digital Elevation Model) acquired in Gomsoman Bay, west coasts of South Korea through the following steps. First, the NDWI(Normalized Difference Water Index) image was generated using the green and near-infrared bands of the given Sentinel-2 satellite image. Then, the binary image that separating lands and waters was generated from the NDWI image based on the pixel intensity value 0.2 as the threshold and the other binary image that separating the upper sea level areas and the under sea level areas was generated from the SRTM DEM based on the pixel intensity value 0 as the threshold. Finally, the coastal wetland map was generated by overlaying analysis of these binary images. The generated coastal wetland map had the 94% overall accuracy. In addition, the other types of wetlands such as inland wetlands or mountain wetlands were not detected in the generated coastal wetland map, which means that the generated coastal wetland map can be used for the coastal wetland management tasks.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.24 no.2
• /
• pp.78-90
• /
• 2021

In order to construct a precision geoid, it has been diversified into land, sea, aviation, and satellite gravity measurement methods, and measurement technology has developed, making it possible to secure high-resolution, high-precision gravity data. The construction of precision geoids can be fast and conveniently decided through GNSS surveys without separate leveling, and since 2014, the National Geographic Information Institute has been developing a hybrid geoid model to improve the accuracy of height surveying based on GNSS. In this study, the results of the GNSS height measurement were compared and analyzed choosing existing public reference points to verify the GNSS height measurement of public surveys. Experiments are conducted with GNSS height measurements and analyzed precision for public reference points on coastal, border, and mountainous terrain presented as low-precision areas or expected-to-be low-precision in research reports. To verify the GNSS height measurement, the GNSS ellipsoid height of the surrounding integrated datum to be used as a base point for the GNSS height measurement at the public datum. Based on the checked integrated datum, the GNSS ellipsoid of the public datum was calculated, and the elevation was calculated using the KNGeoid18 model and compared with the results of the direct level measurement elevation. The analysis showed that the results of GNSS height measurement at public reference points in the coastal, border, and mountainous areas were satisfied with the accuracy of public level measurement in grades 3 and 4. Through this study, GNSS level measurement can be used more efficiently than existing direct level measurements depending on the height accuracy required by users, and KNGeoids 18 can also be used in various fields such as autonomous vehicles and unmanned aerial vehicles.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.29 no.1
• /
• pp.131-141
• /
• 2011

This study, as a purpose of base study for landscape redevelopement of Seowon, pointed out problems of planting patterns in each sector and suggested an alternative through analyzing old literature, complete enumeration survey in each sector and taking aerial images. the conclusions drawn from this study are as follows. A Pilam Seowon(historic site no 242) is located in a Pyungya-Sanrok(plain and mountain) district in Jangsung-gun and has Junhak-Humyo(Study room in the front and Shirne in the back) type. 23 taxonomic group of arbor, 6 taxonomic group of shrub and 5 taxonomic group of flowers are planted high-densitily in limited flat surface. It can be classified into being planted by family and being planted through landscape redevelopement in 1980s. Korean traditional trees are planted in this area like Pinus densiflora, Juniperus chinensis L., Thuja orientalis L., Zelkova serrato Makino, Sophora japonica L., Lagerstroemia indica, Prunus mume include Ginkgo biloba which is old big tree and is registered in Jangsung-gun as protected trees. The tea tree in this area was introduced from wild tea plantation in Yonhwa moutain and was planted. From now on, we have to pay consideration a form management of planted trees in the historical area, rearrangement of plant density due to over planting, removal of alien trees like Pinus bungeana and Canna generalisa, prevention a dwarfishness of main area due to over planting in outside facilities, recovery a alienation among each planting area, and planting concept from plants drawings on wall of buildings can be suggested. The implications of this case study is that introduction of over planting can make more problems like losing sense of place. Therefore, we must do a actual state survey on traditional landscape area like Seowon from preservation point of view.

• Journal of Korean Society of Forest Science
• /
• v.100 no.4
• /
• pp.664-671
• /
• 2011

Random Walk Model can predict the sediment areas of debris flow but it must be extracted three parameters fitted topographical environment. This study developed the method to extract the optimal values of three parameters - Once flowing volume, Stopping slope and Gravity weight - for Random Walk Model. And the extracted parameters were validated by aerial photographs of the debris flowed area. To extract the optimal parameters was randomly performed, limiting the range values of three parameters and developing an accuracy decision method that is called the rate of concordance. The set of the optimal parameters was decided on highest the rate of concordance and a consistency. As a result, the optimal parameters in Bonghwa county were showed that the once flowing volume is $1.0m^3$, the stopping slope is $4.2^{\circ}$ and the gravity weight is 2 when the rate of concordance is -0.2. The validating result of the optimal parameters showed closely that the rate of concordance is average -0.2.

• Korean Journal of Labor Studies
• /
• v.23 no.2
• /
• pp.109-139
• /
• 2017

In light that solidarity movements become significant under the situation of 'labor and labor movement' crisis, our study pays attention to the fact that the Hope Bus campaigns made remarkable achievements, and aims to figure out how those campaigns were successful, by focusing on their solidarity networking. The successful operating conditions of solidarity networking in the Hope Bus campaigns are examined in three aspects - the conditions of triggering, forming, and activating. The solidarity networking of Hope Bus campaigns were mainly triggered by the injustice of layoffs by Hanjin Heavy Industry, aerial protest by Jin-sook Kim, and the tragic symbol of the protest site (Crane no. 85). The solidarity movement of Hope Bus could be formed by the mutual trust and cohesive team-building of key network brokers, their utilization and expansion of social movement networks, and massive ripple effect of SNS-mediated communication. The solidarity networking of Hope Bus was effectively activated by open and de-hierarchical operations of the central planning group, active solidarity activities of participant groups, and the provision of 'heuristic experience' for developing the sensibility to labor solidarity. The virtuous combination of those three operating conditions leads to the building of unified forces among social movements, massive civil participation, and meaningful movement outcomes, through the solidarity networking of Hope Bus campaigns.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.3
• /
• pp.187-201
• /
• 2021

Recently, the demand for a 3D urban spatial information infrastructure for storing, operating, and analyzing a large number of digital data produced in cities is increasing. CityGML is a 3D spatial information data standard of OGC (Open Geospatial Consortium), which has strengths in the exchange and attribute expression of city data. Cases of constructing 3D urban spatial data in CityGML format has emerged on several cities such as Singapore and New York. However, the current ecosystem for the creation and editing of CityGML data is limited in constructing CityGML data on a large scale because of lack of completeness compared to commercial programs used to construct 3D data such as sketchup or 3d max. Therefore, in this study, a method of constructing CityGML data is proposed using commercial 3D mesh data and 2D polygons that are rapidly and automatically produced through aerial LiDAR (Light Detection and Ranging) or RGB (Red Green Blue) cameras. During the data construction process, the original 3D mesh data was geometrically transformed so that each object could be expressed in various CityGML LoD (Levels of Detail), and attribute information extracted from the 2D spatial information data was used as a supplement to increase the utilization as spatial information. The 3D city features produced in this study are CityGML building, bridge, cityFurniture, road, and tunnel. Data conversion for each feature and property construction method were presented, and visualization and validation were conducted.