• Journal of the Korean Wood Science and Technology
• /
• 제17권2호
• /
• pp.26-33
• /
• 1989

The acoustic absorption coefficient and acoustic impedance of 5 species of softwood(sonamoo, sam namoo, gusang namoo, hwaback, sitka spruce) and 5 species of hardwood (Mulgusul namoo, Italian popular, white meranti, red meranti, kalantas) were measured by the standing wave method. which is simple in the setup and gives more accurate result than does any other measuring method. The dependence of the absorption coefficient and complex acoustic impedance on the wood sections. thickness of the sample itself and the back air gap was investigated experimentally in the frequency range from 200Hz to 1800Hz, and the result are as follows: 1. The acoustic absorption coefficient of wood sections was higher on the cross section than radial and tangential sections. 2) The acoustic absorption coefficient were higher in the frequency range from 400Hz to 600Hz, but decreased in the frequency above 600Hz. 3. The genenal tendency of the variation of the normal acoustic impedance was increased according to the frequency. 4. The acoustic absortion coefficient was increased in the to 7mm-thick sample and decreased in 9mm-thick sample. 5. The higher acoustic absorption coefficient was shown in the case with the backing an gap than in the case without the gap.

• Journal of the Korean Wood Science and Technology
• /
• 제22권2호
• /
• pp.25-29
• /
• 1994

The effect of moisture content on acoustic absorption coefficient and impedance of the woods of Pinus densiflora, Chamaecyparis pisifela, Cryptomeria japonica, Abies koreana, Melia azedarch var. japonica, Shorea bracteolata and Shorea acuminata was investigated by standing wave method. The results obtained are summarized as follows: The acoustic absorption coefficient increased with increasing moisture content, but acoustic impedance decreased with increasing moisture content.

• 한국수소및신에너지학회논문집
• /
• 제29권2호
• /
• pp.163-169
• /
• 2018

The present article discusses about the measurement techniques of acoustic impedance that becomes one of the important acoustic characteristics of various boundaries found inside of propulsion systems. Acoustic characteristics including acoustic impedance and reflection coefficient can be often assessed and estimated by use of the two-microphone method. Theoretical expressions of acoustic impedance and reflection coefficient measured in an impedance tube are presented for both cases with mean flow and without flow, and the practical application of the method through calibration is also provided. The acoustic impedance and the reflection coefficient are related with axial locations of microphones, thermodynamic characteristics of gas inside, and the transfer function between the pressure wave measurements at multiple locations.

• Journal of information and communication convergence engineering
• /
• 제14권2호
• /
• pp.78-83
• /
• 2016

In underwater acoustic communication, the transmitted signals are severely influenced by the reflections from both the sea surface and the sea bottom. As very large reflection signals from these boundaries cause an inter-symbol interference (ISI) effect, the communication quality worsens. A channel estimation-based equalizer is usually adopted to compensate for the reflected signals under the acoustic communication channel. In this study, a feed-forward equalizer (FFE) with the least mean squares (LMS) algorithm was applied to a quadrature phase-shift keying (QPSK) transmission system. Two different types of equalizers were adopted in the QPSK system, namely a real-coefficient equalizer and a complex-coefficient equalizer. The performance of the complex-coefficient equalizer was better than that of two real-coefficient equalizers. Therefore, a Hilbert transform was applied to the real-coefficient binary phase-shift keying (BPSK) system to obtain a complex-coefficient BPSK system. Consequently, we obtained better results than those of a real-coefficient equalizer.

• 한국소음진동공학회논문집
• /
• 제15권10호
• /
• pp.1131-1136
• /
• 2005

For the accurate measurement of acoustic properties of a surface, efforts have been made to reduce errors caused by external disturbance. If the reflection coefficient is considered as a transfer function between reflected wane and incident wave, the causality is required between them and the reflection coefficient should be of minimum phase. In this thesis, the minimum phase condition is applied to measure correct reflection coefficient. The reflection coefficient is approximated as a rational function In the Z domain by minimizing the sum square error. Then the minimum phase reflection coefficient is reconstructed using the distribution of poles and zeros of the reflection coefficient model.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.521-524
• /
• 2005

To protect a satellite and electronic equipment from the acoustic loads generated by rocket propulsion system, many launch vehicle use acoustic blanket. Most high frequency region of the acoustic loads is reduced by nose fairing skins and acoustic barrier, but low frequency region is not. In order to control low frequency acoustic mode, we designed away resonator panel which was made of composite materials. This paper shows the absorption coefficient measurement result of resonator and SPL(Sound Pressure Level) reduction by using resonators in a rectangular cavity for experiment. Proper arrangement of acoustic resonators at each mode reduce effectively SPL around the satellite through changing boundary condition.

• 대한기계학회논문집B
• /
• 제30권1호
• /
• pp.32-40
• /
• 2006

A linear acoustic analysis has been performed to elucidate damping characteristics of acoustic cavities in a liquid rocket combustor. Results have shown that resonant frequencies of acoustic cavity obtained by classical theoretic approach and by the present linear analysis are somewhat different with each other. This difference is attributed to the limitation of the simplified classical theory. To quantify the damping characteristics, acoustic impedance has been introduced and resultant absorption coefficient and conductance have been evaluated. Satisfactory agreement has been achieved with previous experiment. Finally the design procedure for an optimal tuning of acoustic cavity has been established.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.770-773
• /
• 2004

The transmission loss coefficient is very important acoustic property in parallel with absorption and acoustic impedance categorizing the acoustical materials, which can control the acoustical problems. At the same time, the transmission loss coefficient is a key parameter to choose the optimum material for the analysis of acoustical characteristics of material using SEA(Statistical Energy Analysis). In this paper, the acoustic transmission loss measurement system using 4-microphone TL tube is applied to the exhaust system, which is one of the most important acoustic control parameters in a car, based on the idea calculating the full transfer matrix. The theoretical background and measurement system are introduced, and finally the measurement results are verified.

• 한국추진공학회지
• /
• 제12권3호
• /
• pp.34-40
• /
• 2008

로켓엔진 연소기의 음향 안정성 향상을 위해, 반파장 공명기의 음향학적 설계인자를 실험적으로 연구하였다. 표준 음향시험 절차에 따라 음향파 응답 신호가 측정되었다. 감쇠인자와 흡음계수가 정량적으로 평가되었고, 이로부터 공명기의 음향감쇠 성능을 파악하였다. 공명기의 직경과 개수, 배치, 연소실의 직경이 설계 인자로 채택되었다. 공명기 직경이 증가함에 따라 음향감쇠 성능이 증가하였다. 연소실 단면에 대한 공명기의 면적비가 최적 값을 초과할 때 과감쇠가 발생하였고, 이로 인해 음향 감쇠 성능이 저하됨을 확인하였다. 공명기 직경이 증가할수록 작은 면적비에서 최적 흡음성능이 달성되었다.

• 한국음향학회지
• /
• 제34권6호
• /
• pp.493-498
• /
• 2015

물로 채워진 음향 펄스 튜브 내에는 가진 조건들에 따라 복잡한 형태의 음향 신호들이 형성될 수 있다. 이는 펄스 튜브를 이용해 저주파수 대역에서 평면파 반사계수를 측정하는 것을 어렵게 한다. 본 연구에서는 COMSOL Multiphysics를 이용하여 튜브 벽이 가진되는 경우 펄스 튜브 내에 평면파 뿐 아니라 비평면파 모우드의 복잡한 음장이 발생됨을 보였다. 모우드 분리 방법인 이차원 푸리에 필터링으로 입사 또는 반사하는 평면파 모우드만을 각각 분리할 수 있었다. 이에 시간 게이팅을 적용하므로 음향 시편의 평면파 반사계수를 보다 정확하게 결정할 수 있게 하였다.