• Analytical Science and Technology
• /
• v.34 no.5
• /
• pp.225-230
• /
• 2021

Currently, most photoluminescence reagents used in forensic science have short stokes shift, making it difficult to observe strong photoluminescence due to scattering light from forensic light sources when using filters that are not shieldable. However interference filters can be observed near monochromatic light, making them a better alternative to absorption filters. To verify practical applicability of interference filters, interference filters and three other types of previously frequently used absorption filters were observed using a variety of light source products, and transmission light was cross-compared. Interference filters have a lower slope value than absorption filters, and selectively show only the photoluminescence of reagents, regardless of the type of product from the forensic light source. In addition, tilting the angle of the filter surface for observation lowered the λ_cut-on, which could replace various types of absorption filters with a single interference filter.

• Journal of Environmental Science International
• /
• v.10 no.1
• /
• pp.9-12
• /
• 2001

In this study, development of new sound absorbent which is safety, economical and efficient with using recycled materials is tried for substitution of commercial sound absorbent. The sound absorbents, used in this investigation, were made of used paper or filters of cigarette butts. With the variation of the material densities, sound absorptions of materials were measured. The impedance tube method is used for measuring sound absorption coefficient of the new sound absorbent materials. The measured frequency range was 250Hz to 4000Hz in 1/3 octave band. The sound absorption coefficient of the commercial materials and that of the materials synthesized in the our laboratory show almost same value.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.36 no.4
• /
• pp.259-263
• /
• 2010

We measured and compared the partition coefficients and absorption levels of preservative phenoxyethanol (PE), antimicrobial ethylhexylglycerin (EG) and UV-filters widely used in cosmetic products and more specifically evaluated the relative absorption level of PE depending on various packaging materials. The resulting partition coefficients of 11 UV filters in relation to PE and EG displayed EG with a relatively higher partition coefficients. The partition coefficients of Tinsorb M and Solaveil CT434 were also high. Among the UV-filter ingredients with EG absorption levels exceeding 40 % were Gransil PSQ, UV Titan M 160 and Micro $TiO_2$ MT 100 TV, whereas Gransil PSQ and Scadder showed PE absorption levels above 40 %. In addition, we confirmed that PE had displayed an absorption level of 7 ~ 8 % as a result of 1 month-long exposure to packaging material polyoxymethylene. This extensive research illustrates the possibility of producing the most potent preservative contents based on studying the relative compatibility between UV-filters and preservatives and selecting the adequate preservatives to be used. Furthermore, preservative level can also decline with passage of time depending on the type of packaging material used.

• Journal of the Korean Ceramic Society
• /
• v.56 no.1
• /
• pp.98-103
• /
• 2019

Optical filters to control light wavelength of displays or cameras are fabricated by multi-layer stacking process of low and high index thin films. The process of multi-layer stacking of thin films has received much attention as an optimal process for effective manufacturing in the optical filter industry. However, multi-layer processing has disadvantages of complicated thin film process, and difficulty of precise control of film morphology and material selection, all of which are critical for transmittance and coloring effect on filters. In this study, the composite $TiO_2$, which can be used to control of UV absorption, coated on nano hollow silica sol, was synthesized as a coating material for optical filters. Furthermore, systematic analysis of the process parameters during the chemical reaction, and of the structural properties of the coating solutions was performed using SEM, TEM, XRD and photo spectrometry. From the structural analysis, we found that the 85 nm nano hollow silica with 2.5 nm $TiO_2$ shell formation was successfully synthesized at proper pH control and titanium butoxide content. Photo luminescence characteristics, excited by UV irradiation, show that stable absorption of 350 nm-light, correlated with a 3.54 eV band gap, existed for the $TiO_2$ shell-nano hollow silica reacted with 8.8 mole titanium butoxide solution. Transmittance observed on substrate of the $TiO_2$ shell-nano hollow silica showed effective absorption of 200-300 nm UV light without deterioration of visible light transparency.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.88-91
• /
• 2003

Electromagnetic interference shielding and near-infrared cutoff filters for plasma display panel application were designed and fabricated by radio frequency magnetron sputtering. Three types of the filters were prepared: the basic structure of type A consisted of [$TiO_2$ Ti Ag $TiO_2$]; type B, of [$TiO_2$ ITO Ag $TiO_2$]; type C, of [$TiO_2$ ITO Ag ITO $TiO_2$]. Ti and ITO layers deposited on Ag layers were employed as barriers to prevent the oxidation and the diffusion of Ag film into the adjacent oxide layers. Optical, electrical, chemical, and structural properties were investigated, and the result shows that the filters with the ITO barrier layers provided an enhancement in transmittance in the visible owing to a lower absorption of ITO layers than Ti layers. Type C filter showed better optical and electrical performances and smoother surface roughness than Type B and C filters: the average sheet resistance was as low as 1.51 $\Omega\Box$ (where $\square$ stands for a square film), the peak transmittance in the visible was as high as 78.2 %, and the average surface roughness was 1.48 nm.

• Horticultural Science & Technology
• /
• v.34 no.1
• /
• pp.84-93
• /
• 2016

Plant factories with artificial lights require a large amount of electrical energy for lighting; therefore, enhancement of light use efficiency will decrease the cost of plant production. The objective of this study was to enhance the light use efficiency by using filters to diffuse the light from LED sources in plant factory conditions. The two treatments used diffuse glasses with haze factors of 40% and 80%, and a control without the filter. For each treatment, canopy light distribution was evaluated by a 3-D ray tracing method and canopy photosynthesis was measured with a sealed acrylic chamber. Sixteen lettuces for each treatment were cultivated hydroponically in a plant factory for 28 days after transplanting and their growth was compared. Simulation results showed that the light absorption was concentrated on the upper part of the lettuce canopy in treatments and control. The control showed particularly poor canopy light distribution with hotspots of light intensity; thus the light use efficiency decreased compared to the treatments. Total light absorption was the highest in the control; however, the amount of effective light absorption was higher in treatments than the control, and was highest in treatment using filters with a haze factor of 80%. Canopy photosynthesis and plant growth were significantly higher in all the treatments. In conclusion, application of the diffuse glass filters enhanced the canopy light distribution, photosynthesis, and growth of the plants under LED lighting, resulting in enhanced the light use efficiency in plant factory conditions.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.6
• /
• pp.52-60
• /
• 1999

Fabricability of phase shifted grating filters has been theoretically studied by an effective index transfer matrix method. In the optical band-pass filter with multiple ${\lambda}/4$ phase-shifts, the phase-shift error and random variation of the grating period should be suppressed such that corresponding resonance frequency lies within, the filter pass-band. The tolerance for the relative error is less than $10^3$, and is quite stringent in typical filters for WDM application. End facet reflection produces ripple in the transmission spectra and the reflectivity should be less than 1% in order to keep the ripple less than 0.25dB. Also, the effect of waveguide absorption loss is enhanced by the resonance in the filter, and the absorption should be limited to 1dB/cm for the signal loss of less than 0.2dB.

• Korean Journal of Optics and Photonics
• /
• v.3 no.1
• /
• pp.55-62
• /
• 1992

The optical absorption characteristics of glasses colored by CdS. CdSe, $CdS_{1-x}Se_x$,ZnS, and ZnSe microcrystallites have been studied with emphasis on changes of the cut-off wavelength. The sharpcut filters with various cut-off wavelengths were fabricated by controlling the composition and the heat-treatment temperature. The cut-off wavelength shifts due to the different heat-treatment temperatures for CdS. CdSe, ZnS, and ZnSe doped SK-16 glasses were found to be relatively small(~30 nm). However, by treating the CdS1,Se, doped SK-16 glasses with different x values at the same heattreatment temperature, it was possible to obtain the filters with various cut-off wavelengths(~130 nm) without losing the high extinction coefficients of the filters. The filter glasses with various cut-off wavelngths(~100 nm) and high extinction coefficiencts were also produced by treating the CdSe and $CdS_{0.5}Se_{0.5}$ doped ZK-1 glasses at different temperatures.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.11
• /
• pp.50-55
• /
• 2009

In this paper, a distributed amplifier is designed using distributed network synthesis that provides the optimum absorption capability of a capacitance. Transfer functions of filters, which consist of the amplifier, are synthesized by a low-pass Chebyshev approximation. Capacitances that a filter network can absorb are calculated as a function of its minimum insertion loss(MIL) and ripple. Active devices in a distributed amplifier are modeled as equivalent circuits by using their S-parameters, and their equivalent capacitances are absorbed into filter structures by properly adjusting the MIL and ripple of a transfer function. As an application example, a distributed amplifier with the gain of about 12.5dB is designed that operates over the frequency range between 0.1 and 7.5GHz. Experimental results prove that distributed network synthesis, which considers capacitance absorption capability, is useful to the design of distributed amplifiers.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.90-90
• /
• 2010

We investigated the modification of optical response properties of titanium dioxide (TiO2) coatings on the ceramic water-purification filters by using ultraviolet-visible absorption spectroscopy and X-ray diffraction. The TiO2 coatings were prepared on ceramic substrate by e-beam evaporation method. These amorphous TiO2 were turned into anatase phase by heat treatment at $700^{\circ}C$ for 2 hours. The doping of N atoms into the TiO2 coatings was done by using 70KeV of N＋ ion implantation with the dose of $1.0{\times}1017$ ions/cm2, followed by post-irradiation heat treatment at $550^{\circ}C$ for 2 hours. Methylene blue test of TiO2 coatings to solar irradiation showed that the post-evaporation heated TiO2 was photocatalytic and N-doped TiO2 reacted to the visible part of solar irradiation.