• ETRI Journal
• /
• v.29 no.2
• /
• pp.143-152
• /
• 2007

In this paper, we propose a time-varying modified minimum mean-squared error (MMSE) detector for the detection of higher data rate signals in a multirate asynchronous code-division multiple-access (CDMA) system which is signaled in a fast Rayleigh fading channel. The interference viewed by a higher data rate symbol will be periodic due to the presence of a lower data rate symbol which spans multiple higher data rate symbols. The detection is carried out on the basis of a modified MMSE criterion which incorporates differential detection and the ratio of channel coefficients in two consecutive observation intervals inherently compensating the fast variation of the channel due to fading. The numerical results obtained by the MMSE detector with time-varying detection show around 3 dB (M=2) and 6 dB (M=4) performance improvement at a BER of $10^{-3}$ in the AWGN channel, while introducing more computational complexity than the MMSE detector without time-varying detection. At a higher $E_b/N_0$, the proposed scheme can achieve a BER of approximately $10^{-3}$ in the presence of fast channel variation which is an improvement over other schemes.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.6_2
• /
• pp.625-633
• /
• 2007

Recently human beings are enforcing marine investigations to extend their living environment from land to the sea. Therefore, this study grasped objects in the bottom of the sea and its topographical undulation and acquired topographic map with a sound detector. In result, This study acquired their images with a sound detector and can draw up a Drawing of Sea Mapping and a three-dimensional modeling map.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.842-850
• /
• 2018

In this paper, the design and fabrication of a frequency-locked-loop(FLL) 5-GHz oscillator with a single resonator is presented. The proposed oscillator is the simplified version of the previous FLL oscillator with two separate resonators in the VCO and frequency detector. The resonator is commonly used in the VCO and frequency detector of the proposed oscillator configuration. The 5-GHz oscillator is implemented on the hetero-multilayer substrate composed of a Rogers' RO4350B laminate, which has excellent high-frequency performance, and the commercial FR4 three-layer substrate. The frequency locking occurs at approximately 5 GHz and has an output power of 3.8 dBm. The phase noise has a free-run VCO phase noise at frequencies above 1 kHz, and an FLL background noise at frequencies below 1 kHz. For this loop-filter, the phase noise showed an improvement of approximately 12 dB at the offset-frequency of 100 Hz.

• Biomedical Engineering Letters
• /
• v.8 no.4
• /
• pp.383-392
• /
• 2018

For prompt gamma ray imaging for biomedical applications and environmental radiation monitoring, we propose herein a multiple-scattering Compton camera (MSCC). MSCC consists of three or more semiconductor layers with good energy resolution, and has potential for simultaneous detection and differentiation of multiple radio-isotopes based on the measured energies, as well as three-dimensional (3D) imaging of the radio-isotope distribution. In this study, we developed an analytic simulator and a 3D image generator for a MSCC, including the physical models of the radiation source emission and detection processes that can be utilized for geometry and performance prediction prior to the construction of a real system. The analytic simulator for a MSCC records coincidence detections of successive interactions in multiple detector layers. In the successive interaction processes, the emission direction of the incident gamma ray, the scattering angle, and the changed traveling path after the Compton scattering interaction in each detector, were determined by a conical surface uniform random number generator (RNG), and by a Klein-Nishina RNG. The 3D image generator has two functions: the recovery of the initial source energy spectrum and the 3D spatial distribution of the source. We evaluated the analytic simulator and image generator with two different energetic point radiation sources (Cs-137 and Co-60) and with an MSCC comprising three detector layers. The recovered initial energies of the incident radiations were well differentiated from the generated MSCC events. Correspondingly, we could obtain a multi-tracer image that combined the two differentiated images. The developed analytic simulator in this study emulated the randomness of the detection process of a multiple-scattering Compton camera, including the inherent degradation factors of the detectors, such as the limited spatial and energy resolutions. The Doppler-broadening effect owing to the momentum distribution of electrons in Compton scattering was not considered in the detection process because most interested isotopes for biomedical and environmental applications have high energies that are less sensitive to Doppler broadening. The analytic simulator and image generator for MSCC can be utilized to determine the optimal geometrical parameters, such as the distances between detectors and detector size, thus affecting the imaging performance of the Compton camera prior to the development of a real system.

• Journal of Biomedical Engineering Research
• /
• v.29 no.5
• /
• pp.364-370
• /
• 2008

Recent development in large area flat-panel x-ray detector technology enables clinical application of digital tomosyntesis. Unlike conventional motion tomography using x-ray films, flat-panel x-ray detectors provide projection images in digital formats so that tomographic images can be synthesized in a more flexible way. For the digital tomosynthesis, precise movements of the x-ray source and the x-ray detector with respect to a fulcrum point are necessary. In this study, we apply the digital tomosynthesis technique to the flat-panel detector based micro-CT in which the flat-panel detector and the x-ray source rotate together on a circular arc. The experimental results suggest that flat-panel detector based 3D CTs can be used for digital tomosynthesis in the clinical environment.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.23 no.3
• /
• pp.161-167
• /
• 1997

Determination of several cationic surfactants in cosmetics has been investigated. Reverse phase ion pair chromatography was used to identify and quantitate cationic surfactants. Cationic surfactants analyzed in this experiment were cetylpyridium chloride, stearyltrimetylammonium chloride, bezalkonium chloride, benzyldicethylcetylammonium chloride, and bihenyltrimethyl ammonium chloride. The separation was achieved on a reverse phase coumn with 10mM HCl-acetonitrile eluent. In this condition, the most of cationic surfactants with exception of CPC and CTAC respectively with suppressed conductivity detector and UV detector connected in series. The calibration curves obtained by plotting the peak areas of the cationic surfactants were linear at levels ranging from 0.005 to 0.1% correlation coefficient, r=0.9988. The detection limits were 1 to 5ppm in sample solution. The average recoveries of cationic surfactants added to hair treatment cream and hair rinse in three to five experiments were 96.7 105.2% and relative standard deviations were 1.1-3.8%. The case that there were CPC and CTAC in same solution was also tested. CPC and CTAC which couldn't be separated on reverse phase column were quantitated with suppressed conductivity detector and UV detector connected in series. Recovery of CPC and CTAC were 101.6 and 89.2% respectively. The proposed method was applied to the determination of cationic surfactants in commercial hair treatment cream.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.1
• /
• pp.57-62
• /
• 2009

Purpose: Brain SPECT study is more sensitive to motion than other studies. Especially, when applying 1-day subtraction method for Diamox SPECT, it needs shorter study time in order to prevent reexamination. We were required to have new study condition and analysing method on dual detector system because triple head camera in Seoul National University Hospital is to be disposed. So we have tried to increase image quality and make the dual and triple head to have equivalent study time by using a new analysing program. Materials and Methods: Using IEC phantom, we estimated contrast, SNR and FWHM. In Hoffman 3D brain phantom which is similar with real brain, we were on the supposition that 5% of injected doses were distributed in brain tissue. To compare with existing FBP method, we used fan-beam collimator. And we applied 15 sec, 25 sec/frame for each SEPCT studies using LEHR and LEUHR. We used OSEM2D and Onco-flash3D reconstruction method and compared reconstruction methods between applied Gaussian post-filtering 5mm and not applied as well. Attenuation correction was applied by manual method. And we did Brain SPECT to patient injected 15 mCi of $^{99m}Tc$-HMPAO according to results of Phantom study. Lastly, technologist, MD, PhD estimated the results. Results: The study shows that reconstruction method by Flash3D is better than exiting FBP and OSEM2D when studied using IEC phantom. Flowing by estimation, when using Flash3D, both of 15 sec and 25 sec are needed postfiltering 5 mm. And 8 times are proper for subset 8 iteration in Flash3D. OSEM2D needs post-filtering. And it is proper that subset 4, iteration 8 times for 15sec and subset 8, iteration 12 times for 25sec. The study regarding to injected doses for a patient and study time, combination of input parameter-15 sec/frame, LEHR collimator, analysing program-Flash3D, subset 8, iteration 8times and Gaussian post-filtering 5mm is the most appropriate. On the other hands, it was not appropriate to apply LEUHR collimator to 1-day subtraction method of Diamox study because of lower sensitivity. Conclusions: We could prove that there was also an advantage of short study time effectiveness in Dual camera same as Triple gamma camera and get great result of alternation from existing fan-beam collimator to parallel collimator. In addition, resolution and contrast of new method was better than FBP method. And it could improve sensitivity and accuracy of image because lesser subjectivity was input than Metz filter of FBP. We expect better image quality and shorter study time of Brain SPECT on Dual detector system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1147-1158
• /
• 2008

In this paper, we designed a phase-looking circuit that locks the 16.8 GHz VTDRO to a 700 MHz SAW oscillator using SPD as a phase detector Direct phase locking with loop filter alone causes the problem of lock time, so VTDRO is phase leered by loop filter with the aid of time varying square wave current generator. The current generator is related to the loop filter and needs the systematic toning. In this paper, a systematic design of the current generator and loop filter is presented. The fabricated PLDRO shows a stabilized frequency of 16.8 GHz, a output power 6.3 dBm, and a phase noise of -101 dBc/Hz at the 100 kHz offset.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.971-978
• /
• 2005

In this paper, we design and fabricate a VCO(Voltage Controlled Oscillator) for radar detector of X/K/Ka band using frequency multiplier. The existing VCO operated in radar detector have many Problems such as narrow bandwidth, slow frequency variable rate, unstable of production due to high frequency. So we design and fabricate a VCO improved such problems using frequency multiplier. As a result of measure, investigated frequency multiple VCO show its output power 3.64 dBm at multiplied operating frequency 11.27 GHz and have wide frequency tuning range of 660 MHz by controlled voltage 0V to 4.50 V applied diode. And also its phase noise is -104.0 dEc at 1 MHz offset frequency so we obtain suitable performance for commercial use.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1871-1875
• /
• 1997

Crane operation is manually accomplished by skilled operators. Recently, the concept of automation is widely introduced in shipping and unloading operation using the overhead crane for the enhanced productivity. In this regards, we designed an angle detector and 3D position detectro which are key evices for this operation. As well as an intellignet control algorithm is developed for the implementation of swing free crane. The performance of the presented algorithm is tested for the swing angle and the position of the overheas crand. The control scheme adopts a feedback control of an angular velocity of swing in initial phase and then the fuzzy controller whose rule base is optimized by a genetic algorithm.