• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.79-79
• /
• 2009

Samples of Ta-doped in $In_2O_3-ZnO-SnO_2$(IZTO) with a doping level up to 4wt% were sintered at $1600^{\circ}C$ in $O_2$. The crystal phase of the samples was identified by an X-ray diffraction experiment. apparent density and porosity with sintered temperature from $1500^{\circ}C$ to $1640^{\circ}C$ are mesured by archimedes method. For each sample, the specific resistivity was determined. samples of sintered at $1600^{\circ}C$ had the highest density and lowest porousity and The Ta 0.25-wt%-doped IZTO ceramics had the lowest resistivity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.214.2-214.2
• /
• 2015

본 연구에서는 Zr을 첨가한 용액 공정 기반 ZTO:Zr 산화물 반도체 제작 및 열처리 온도에 따른 트랜지스터의 특성 변화를 분석하였다. Zn:Sn=4:7 비율로 고정하고, Zr (0~1%) 비율에 따른 도핑과 열처리 온도($350{\sim}550^{\circ}C$)를 가변하였다. 실험 결과, Zr의 비율이 증가할수록 전류와 이동도가 감소하였고, 문턱전압이 양의 방향으로 이동하는 것을 확인하였다. Zr는 SEP (Standard Electrode Potential)가 -1.45로 Zn (-0.76), Sn (-0.13) 보다 작아 금속과 산소의 결합을 증가시키며, 또한 밴드갭이 ~7 eV로 다른 금속 보다 높아 산소와 결합력이 높다. 이러한 요인은 산화물 내의 산소 원자 결함(Oxygen vacancy)을 감소시킨다. 반대로 열처리 온도가 높아질수록 탈 수산화(Dehydroxylation)로 인한 산소 원자 결함이 증가시켜, Zr 도핑 효과와 반대 경향을 보인다. 실험 결과를 통해 Zr:Zn:Sn=0.5:4:7의 비율과 $550^{\circ}C$ 열처리 조건에서 문턱전압과 이동도, 아문턱 스윙, 전류 온오프 비(Ion/Ioff)가 각각 0.68V, $0.18cm^2/Vs$, 1.06 V/dec, $1.6{\times}10.6$의 특성을 확인하였다.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.537-544
• /
• 2001

In the present study, tin-zinc alloys were coated on a cold-rolled steel sheet with variations of electrolyte concentration, additives quantity and current density employing the Hull cell and circulation cell simulator. With an addition of additives of 2m1/L, tin-zinc deposits containing 10 to 40 percent Zn revealed a good surface appearance with weak acidic electrolytes. The organic additives suppressed the Sn deposition rate and thus increased the zinc contents in tin-zinc coating layers. The zinc contents in the tin-zinc coating layers depended almost linearly on the concentrations of metal ions of tin and zinc. Temperature of the electrolyte affected the composition tin-zinc coating layer. However, the concentration of complexants revealed little effectiveness. The surface morphology of tin-zinc coating showed dense tin and zinc phases with fine equiaxed grains with the high current density.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.76-79
• /
• 2011

In order to improve efficiency and make a new material thin film, we prepared the Al-In-Sn-ZnO thin film on a glass substrate at room temperature using a Facing Target Sputtering (FTS) system. The FTS system was designed to array two targets that face each other. Two different kinds of targets were installed on the FTS system. We used an ITO ($In_2O_3$ 90wt%, $SnO_2$ 10wt%) target and an AZO (ZnO 98wt%, $Al_2O_3$ 2wt%) target. The AIZTO films were deposited using different applied powers to the targets. The as-deposited AIZTO thin films were investigated using a UV/VIS spectrometer, an X-ray diffratometer (XRD), and Energy Dispersive X-ray spectroscopy (EDX).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.1
• /
• pp.18-21
• /
• 2014

Because the Pb-based piezoelectric materials showed problems such as an environmental pollution. lead-free $O_3$ materials were studied in the present study. The $O_3$ thin films were deposited at $640^{\circ}C$ on $Pt/Ti/SiO_2$ substrate by pulsed laser deposition (PLD) and were annealed for 5 min at $750^{\circ}C$ using rapid thermal annealing (RTA) in nitrogen atmosphere. Samples annealed at $750^{\circ}C$ showed a smooth morphology and an improvement of the dielectric and leakage properties, as compared with as-grown samples. However, electrical properties of the $O_3$ thin films obtained in the present study should be improved for piezoelectric applications.

• Transactions of Materials Processing
• /
• v.25 no.3
• /
• pp.155-160
• /
• 2016

Magnesium(Mg) alloys have been evaluated as replacements for steel or aluminum parts in the automobile industry because of the fuel economy they can provide through reducing weight. The application of Mg alloys has been limited due to its low formability at room temperature, which results from a small number of active slip systems. In the current study, an extruded TAZ711(Mg-7Sn-1Al-1Zn) alloy was warm forged into an automotive control arm to evaluate its formability at various forging temperature. Warm forging was conducted at temperatures of 200, 250, 350 and 450℃. Static strength evaluation was performed on the as-forged specimen at 250℃. The results showed good static strength.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.697-700
• /
• 2011

Thin-film transistors(TFTs) with magnesium zinc tin oxide(MZTO) channel layer are fabricated by solution-process. The threshold voltage (Vth) shifted toward positive directly with increasing Mg contents in MZTO system. Because the Mg has a lower standard electrode potential (SEP) than Sn, Zn, thus degenerate the oxygen vacancy ($V_O$). As a result, the Mg act as carrier suppressor and oxygen binder in the MZTO as well as a Vth controller.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.472.1-472.1
• /
• 2014

현재 Cu(In,Ga)Se2나 Cu2ZnSn(S,Se)4 (CZTSSe)계 박막태양전지의 버퍼층으로 가장 많이 사용되는 물질은 CdS이다. 하지만 Cd의 독성 문제로 인해 사용에 제약이 있고, CdS의 작은 밴드갭(~2.4 eV)으로 인해 단 파장 영역에서 광활성층의 빛 흡수를 저해하는 문제 때문에 새로운 대체 물질을 찾으려는 연구가 많이 이루어지고 있다. 이러한 관점에서, ZnS계 물질은 독성 원소인 Cd을 사용하지 않고, 3.6 eV 정도의 큰 밴드갭을 가지기 때문에, CdS 버퍼층을 대체하기 위한 물질로 관심을 받고 있다. ZnS계 버퍼층을 증착하는 위해 chemical bath deposition (CBD), molecular beam epitaxy (MBE), thermal evaporation, spray pyrolysis, sputtering, elecrtrodepostion 등의 다양한 공정이 사용될 수 있다. 본 연구에서는 상기의 다양한 공정 가운데, 공정 단가가 낮고, 대면적 공정에 용이한 CBD 공정을 이용하여 ZnS계 버퍼층을 증착하는 연구를 수행하였다. 용액의 조성, 농도, 공정 온도, 시간 등을 비롯한 다양한 공정 변수가 ZnS계 박막의 morphology, 조성, 결정성, 광학적 특성 등 다양한 특성에 미치는 영향이 체계적으로 연구되었다. 또한, 상기 ZnS계 버퍼층을 CZTSSe 박막태양전지에 적용하여 CdS를 성공적으로 대체할 수 있음을 확인하였다. 본 연구를 통하여 ZnS계 버퍼층이 향후 친환경적인 박막태양전지 제조에 활용될 수 있는 가능성을 확인할 수 있었다.

• Korean Journal of Environmental Agriculture
• /
• v.31 no.2
• /
• pp.122-128
• /
• 2012

BACKGROUND: Mine drainage from metal mining districts is a well-recognized source of environmental contamination. Oxidation of metal sulfides in mines, mine dumps and tailing impoundments produces acidic, metal-rich waters that can contaminate the local surface water and soil. METHODS AND RESULTS: This experiment was carried out to investigate the pollution assessment of heavy metal on the water quality of mine drainage, paddy soils and sediment in lower watershed affected by mine drainage of the Sambo mine. The average concentrations of dissolved Cd (0.018~0.035 mg/L) in mine drainage discharged from the main waste rock dumps(WRD) was higher than the water quality standards (0.01 mg/L) for agricultural water in Korea. Also, the average concentrations of dissolved Zn, Fe and Mn were higher than those of recommended maximum concentrations (Zn 2.0, Fe 5.0, Mn 0.2 mg/L) of trace metal in irrigation water proposed by FAO (1994). The average contents of Pb and Zn in paddy soils was higher than those of standard level for soil contamination(Pb 200, Zn 300 mg/kg) in agricultural soil by Soil Environmental Conservation Act in Korea. Also, the concentrations of Cd, Pb and Zn in sediment were higher than those of standard level for soil contamination (Cd 10, Pb 400, Zn 600 mg/L) in waterway soil by Soil Environmental Conservation Act in Korea. The enrichment factor (EFc) of heavy metals in stream sediments were in the order as Cd>Pb>Zn> As>Cu>Cr>Ni. Also, the geoaccumulation index (Igeo) of heavy metals in stream sediments were in the order as Zn>Cd>Pb>Cu>As>Cr>Ni, specially, the geoaccumulation index (Igeo) of Zn (Igeo 3.1~6.2) were relatively higher than that of other metals in sediment. CONCLUSION(s): The results indicate that stream water and sediment were affected by mine drainage discharged from the Sambo mine at least to a distance of 1 km downstream (SN-1, SN-2) of the mine water discharge point.

• Journal of the Korean Ceramic Society
• /
• v.55 no.4
• /
• pp.368-375
• /
• 2018

This study deals with the color formation of ceramic pigment in the $TiO_2$-SnO-ZnO system. We designed compounds to control the color formation depending on the composition using the Design of Experiment. The color coordinate values of synthesized pigments, $L^*a^*b^*$ were measured and statistically analyzed color for changing elements depending on its composition. The relationship between the major crystalline phases and chromaticity was examined using XRD, and the oxidation states of each element were analyzed by XPS. The synthesized pigments based on the compound design exhibited various color changes ranging from yellow-orange to green-blue and brown. The statistical analysis on the spectrophotometer results shows that $a^*$ and $b^*$ values decreased with $TiO_2$ content, and increased with SnO content. Yellow-orange color was detected with the main peak of SnO, and the green-blue color developed with the main peak of $Zn_2TiO_4$. The $a^*$ and $b^*$ values increased with increased SnO peak intensity, and decreased with increased $Zn_2TiO_4$ peak intensity. The results revealed that pigment color formation was influenced by changes in the main crystalline phases and crystalline intensity. However, XPS analysis of the oxidation states of each element showed little correlation with the pigment chromaticity result.