• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.109-114
• /
• 2003

The purpose of this study Is to investigate the effect of $V_2$O$_{5}$ addition on the microstructures and magnetic properties of 7.7${\times}$4.5${\times}$1.0 mm sized multi-layer chip inductors prepared by the screen printing method using 0∼0.5 wt％ $V_2O_{5}$-doped NiCuZn ferrite pastes. With increasing the $V_2O_{5}$ content, the exaggerated grain growth of ferrite layers was developed due to the promotion of Ag diffusion and Cu segregation into the grain boundaries oi ferrites, which affected significantly the magnetic properties of the chip inductors. After sintering at $900^{\circ}C$, the inductance at 10 MHZ of the 0.5 wt％ $V_2O_{5}$-doped chip inductor was 3.7 ${\mu}$H less than 4.2 ${\mu}$H of the 0.3 wt% $V_2O_{5}$-doped one, which was thought to be caused by the residual stress at the ferrite layers increased with the promotion of Ag diffusion and Cu segregation. The quality factor of the 0.5 wt% $V_2O_{5}$-doped chip inductor decreased with increasing the sintering temperature, which was considered to be caused by the electrical resistivity of the ferrite layer decreased with the promotion of Ag/cu segregation at the grain boundaries and the growth of the mean grain size of ferrite due to exaggerated grain growth of ferrite layers.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.221-228
• /
• 1991

In this study we have investigated the sealing characteristics of glasses suitable for producing the magnetic gap of the ferrite head cores which have been widely used for VTR and computer magnetic heads. $PbO-B_2O_3$ g1asses were evaluated by measuring microhardness, thermal expansion coefficient and sliding wear resistance. Concentration distribution of elements at the interface was observed by WDS. wettability was measured by high temperature microscopy. The results were as follows ; 1. In sealing glasses of $PbO-B_2O_3$ system, thermal expansion coefficient and wear volume were increased with increasing PbO content, and were decreased with increasing $B_2O_3$ content. 2. The contact angle of $PbO-B_2O_3$ Systems was mainly influenced by PbO content. 3. The sealing temperature showed a tendency to decrease proportionally with the increase of the coefficient of thermal expansion. 4. The diffusion at the interface between Mn-Zn single crystal ferrite and sealing glasses of $PbO-B_2O_3$ system was dominated by small amount of diffusion of ferrite content into glass part, which was very little affected by sealing heat treatment time.

• Journal of the Korean Chemical Society
• /
• v.20 no.6
• /
• pp.494-499
• /
• 1976

The extraction-polarographic method applied to the determination of micro amount of chromium (Ⅵ). Chromium(Ⅵ) was extracted into methylisobuthylketone(MIBK) layer containing diethyldithiocarbamate(DDTC) as Cr(Ⅲ)-DDTC complex from acetate buffered aqueous, solution of pH 5.4 and the direct current polarogram for the extract was recorded after addition of sodium perchlorate as supporting electrolyte. The reduction current was diffusion controlled. And the half wave potential of this reduction wave was -0.81 volt vs. SCE. The diffusion current was proportional to the chromium concentraticn in aqueous solution in the range of 8∼160 ppm. And the chromium(Ⅵ) could be selectively determined in the presence of chromium(Ⅲ), since the chromium(Ⅲ) did not interfere up to twice the amount of chromium(Ⅵ). Many of other metals such as Mn(Ⅱ), Cu(Ⅲ), Zn(Ⅱ), Mg(Ⅱ), Ni(Ⅱ) and Ag(Ⅰ) were found to have no effect even when present in 1000 times the amount of chromium (Ⅵ).

• Journal of Environmental Health Sciences
• /
• v.42 no.1
• /
• pp.61-70
• /
• 2016

Objectives: The purpose of this study is to determine the exposure risk to tattoo components by analyzing skin absorption using the in vitro method. Tattoos are commonly used for cosmetic purposes, and the skin of not only the operator but of the people who are undergoing the cosmetic procedure is continuously exposed to hazardous chemicals. Methods: Skin permeation risk determination was conducted by the in vitro Franz diffusion cell method according to the ingredient types of tattoo dyes, such as volatile organic compounds (VOCs), non-volatile organic compounds and heavy metals, using hairless mouse full skin and human cadaver epidermis. Results: The major components with good skin penetration for each type of tattoo dye ingredient were clarified. Among the tatto dye ingredients, 1,2-Dichlorobenzene, Zn, Al, Pb and Ti showed good skin penetration. Most of the skin transmission rates were higher in hairless mouse full skin than in human cadaver epidermis. Conclusion: A possible exposure risk to hazardous substances in tattoo dyes was confirmed from this study. These results are expected to provide a positive contribution to the establishment of management regulations for tattoo dyes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.393-393
• /
• 2016

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. Stainless steel과 같은 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 기존의 두껍고 추가 장비가 요구되는 SiOx나 Al2O3 대신 200nm 이하의 ZnO 박막을 이용하여 확산방지막을 제조하였다. 유연기판으로 STS 430 stainless steel을 이용하였다. 먼저 stainless steel 기판을 이용하여 기판에 의한 흡수층의 특성을 분석하였으며 ZnO 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.7%로 증가하였다. 그 후 기판으로부터 확산되는 불순물의 유입에 의한 결함을 분석하기 위해 DLTS를 이용하여 소자 특성을 분석하였다. 온도는 80~300K으로 가변하며 측정을 실시하였으며 그 후 계산을 통해 activation energy와 capture cross section 값을 구하였다. DLTS 분석 결과 Ni이 CIGS 흡수층으로 확산되어 NiCu anti-site를 형성하여 태양전지의 효율을 감소시키는 것을 확인하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.328-333
• /
• 2011

The influence of Al-doped ZnO (AZO) thin films degraded under high temperature and damp heat on the performance deterioration of Cu(In,Ga)$Se_2$ (CIGS) solar cells was investigated. CIGS solar cells with AZO/CdS/CIGS/Mo structure were prepared on glass substrate and exposed to high temperature ($85^{\circ}C$) and damp heat ($85^{\circ}C$/85% RH) for 1000 h. As-prepared CIGS solar cells had 64.91% in fill factor (FF) and 12.04% in conversion efficiency. After exposed to high temperature, CIGS solar cell had 59.14% in FF and 9.78% in efficiency, while after exposed to damp heat, it had 54.00% in FF and 8.78% in efficiency. AZO thin films in the deteriorated CIGS solar cells showed increases in resistivity up to 3.1 times and 4.4 times compared to their initial resistivity after 1000 h of high temperature and damp heat exposure, respectively. These results can be explained by the decreases in carrier concentration and mobility due to diffusion or adsorption of oxygen and moisture in AZO thin films. It can be inferred that decreases in FF and conversion efficiency were caused by an increase in series resistance, which resulted from an increase in resistivity of AZO thin films degraded under high temperature and damp heat.

• Journal of the Korean Chemical Society
• /
• v.45 no.5
• /
• pp.429-435
• /
• 2001

The monomer N,N'-bis(2-pyrrol-1-yl-propyl)-4,4'-bipyridine(bpb) was electrochemically polymerized on the glassy carbon electrode surface, which was modified with 1:1 ratio of erichrome black T(EBT) and glutathione(GSSG) to give a type of GC/poly-bpb, EBT, GSSG electrode for depositing Zn(II). The diffusion coefficients of the incorporated ions were 2.43${\times}10^{-15}$ and 9.14${\times}10^{-15} cm^2s^{-1}$ before taking Zn(II) ions and after them respectively. The modified electrodes are stable at the electrode process. The polymerized poly-bpb of 2.83${\times}10^4gmol^{-1}$ can deposit 2.15${\times}10^4gmol^{-1}$ of Zn(II). The number of pumping ions involving in the redox procedure at 0.77 V was 81.7% of the captured 180 ions into the polymer matrix, which was 3 times larger than that of the electrode modified with EBT alone.

• Journal of Powder Materials
• /
• v.15 no.2
• /
• pp.95-100
• /
• 2008

The investigation is to modify the mechanical and chemical properties of Mg alloys using a combination of rapid solidification and surface treatment. As the first approach, $Mg_{95}Zn_{4.3}Y_{0.7}$ was gas atomized and pressure sintered by spark plasma sintering process (SPS), showing much finer microstructure and higher strength than the alloys as cast. Further modification was performed by treating the surface of PM Mg specimen using Plasma electrolytic oxidation (PEO) process. During the PEO processing, MgO layer was initiated to form on the surface of Mg powder compacts, and the thickness and the density of MgO layer were varied with the reaction time. The thickening rate became low with the reaction time due to the limited diffusion rate of Mg ions. The surface morphology, corrosion behavior and wear resistance were also discussed.

• Nuclear Engineering and Technology
• /
• v.50 no.3
• /
• pp.416-424
• /
• 2018

Microstructure of oxide formed on Zr-Nb-Sn tube sample was intensively examined by scanning transmission electron microscopy after exposure to simulated primary water chemistry conditions of various concentrations of Zn (0 or 30 ppb) and dissolved hydrogen ($H_2$) (30 or 50 cc/kg) for various durations without applying desirable heat flux. Microstructural analysis indicated that there was no noticeable change in the microstructure of the oxide corresponding to water chemistry changes within the test duration of 100 days (pretransition stage) and no significant difference in the overall thickness of the oxide layer. Equiaxed grains with nano-size pores along the grain boundaries and microcracks were dominant near the water/oxide interface, regardless of water chemistry conditions. As the metal/oxide interface was approached, the number of pores tended to decrease. However, there was no significant effect of $H_2$ concentration between 30 cc/kg and 50 cc/kg on the corrosion of the oxide after free immersion in water at $360^{\circ}C$. The adsorption of Zn on the cladding surface was observed by X-ray photoelectron spectroscopy and detected as ZnO on the outer oxide surface. From the perspective of $OH^-$ ion diffusion and porosity formation, the absence of noticeable effects was discussed further.

• Economic and Environmental Geology
• /
• v.37 no.3
• /
• pp.311-324
• /
• 2004

We investigated the contamination and behavior of heavy metals in stream sediments within the watershed of Juam Reservoir. Many abandoned mines within the reservoir can act as a potential contaminant source for water quality. Heavy metal concentrations (Cr, Cu, Ni, Pb and Zn) in stream sediments from watershed are very low, indicating that content of heavy metals in the sediments probably do not affect the water quality in Juam Reservoir. However Pb concentration in the stream sediments increases downward streams, suggesting the possible diffusion of Pb contamination. According to the leaching ratio for stream sediments at a strong acidic condition in the abandoned mine areas, the relative mobility for metals decreases in the order of Pb＞Zn=Cu＞Ni＞Cr, indicating that Pb can have a bad effect upon the water quality in Jum Reservoir. Moreover, if contaminated sediment is placed in the bottom of reservoir (i.e., reducing condition), the relative mobility of Pb is the highest, indicating that Pb in the bottom sediments can be leached to water at interface between water and sediment with changing in physicochemical conditions.