• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.410-413
• /
• 2004

In this paper, a simulator system for Fuel Cell Hybrid Electric Vehicles(FCHEV) is implemented using DSP boards with CAN bus. The subsystems of a FCHEV i.e., the fuel cell system, the battery system, the vehicle dynamics with the transmission mechanism are coded into 3 DSP boards. The power distribution control algorithm and battery SOC control are also coded into a DSP board. The real-time monitoring program is also developed to examine the control performance of power control and SOC control algorithms.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.842-846
• /
• 2004

Both traffic congestion and air pollution in the metropolitan area can be greatly relieved by promoting the use of public transportation with zero emission system. Bus and subway are very convenient means for the people moving in the route areas. But they are not enough to satisfy handicapped or old people to have access to them and also do not solve environmental problems completely. New vehicle system, fuel cell track rapid transit, will be introduced as a countermeasure for such problems in the present paper.

• International Journal of Automotive Technology
• /
• v.8 no.5
• /
• pp.575-581
• /
• 2007

As current and future automobile emission regulations become more stringent, the research on flow distribution for an exhaust manifold and close-coupled catalyst(CCC) has become an interesting and remarkable subjects. The design of a CCC and exhaust manifold is a formidable task due to the complexity of the flow distribution caused by the pulsating flows from piston motion and engine combustion. Transient flow at the exhaust manifold can be analyzed with various computational fluid dynamics(CFD) tools. However, the results of such simulations must be verified with appropriate experimental data from real engine operating condition. In this study, an experimental approach was performed to investigate the flow distribution of exhaust gases for conventional cast types and stainless steel bending types of a four-cylinder engine. The pressure distribution of each exhaust sub-component was measured using a simulated dynamic flow bench and five-hole pitot probe. Moreover, using the results of the pitot tube measurement at the exit of the CCC, the flow distribution for two types of manifolds(cast type and bending type) was compared in terms of flow uniformity. Based on these experimental techniques, this study can be highly applicable to the design and optimization of exhaust for the better use of catalytic converters to meet the PZEV emission regulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.4
• /
• pp.319-325
• /
• 2004

The major factors that make ZEV affordable are the range and cost. The development of advanced batteries such as Ni-MH battery can solve the problem partly； on the hand the battery management system is an efficient way. Ni-MH battery and battery ECU is a key component influencing ZEV performance, such as range, acceleration and hill-climbing capability. Because most problems related to battery such as short circuit, over-discharge and overcharge occur easily during operation, it is necessary to develop a dedicated battery ECU for HEV. This paper proposes a new SOC algorithm for the HEV based on the terminal voltage and current integration. And battery ECU was designed and analyzed. Also, the validity is confirmed through experiment.

• Journal of ILASS-Korea
• /
• v.28 no.2
• /
• pp.62-67
• /
• 2023

Recently, the global automobile industry is aiming for a transition from internal combustion locomotives to zero-emission vehicles. Electric vehicles powered by battery energy can operate at peak performance and improve fuel economy by applying multiple motors or multi-speed transmissions. In order to design a two-speed transmission, it is necessary to evaluate and analyze the application system and performance of electric vehicles. In this study, control performance optimization of a twostage battery electric vehicle equipped with an AMT-based automatic transmission was performed and performance according to control pattern changes was analyzed. In order to improve the operating efficiency of the motor, the shift control that sets the optimal operating point according to the vehicle speed and required torque was derived from the motor efficiency map. The performance of battery energy consumption and transmission loss energy according to the hysteresis interval was analyzed and optimized. The hysteresis interval applied to the optimal shift map acted as a factor in reducing the frequency and loss of shifts. It has been shown that keeping the hysteresis interval at about 4 km/h can reduce energy consumption while reducing the number of shifts.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.498-503
• /
• 2012

It happens that the fuel is not injected when the driver doesn't push the acceleration pedal of vehicle with engine speed higher than 1,500rpm above the mid range of vehicle speed. This is called "fuel-cut function" and almost every modern vehicle is equipped with this function. This is activated frequently on the downhill area of highway and the quantity of vehicle-exhausted $CO_2$ gas can be zero on this area. With this fuel-cut function on the test highway, $CO_2$ gas from passenger car(2,000cc engine volume) can be reduced up to 4%. The fuel-cut function with CRUISE made in company AVL is simulated to find the most effective driving pattern on the downhill area. By simulating with CRUISE software, it is found that the lower limit of vehicle speed for fuel-cut should be raised to improve the fuel economy on the steeper downhill road. The fuel economy can be most economical when fuel-cut driving and reacceleration are completed on the section of downhill road.

• Journal of Hydrogen and New Energy
• /
• v.28 no.1
• /
• pp.56-62
• /
• 2017

Although most electricity production contributes to air pollution, the vehicle organizations and environmental agency categorizes all EVs as zero-emission vehicles because they produce no direct exhaust or emissions. Currently available EVs have a shorter range per charge than most conventional vehicles have per tank of gas. EVs manufacturers typically target a range of 160 km over on a fully charged battery. The energy efficiency and driving range of EVs varies substantially based on driving conditions and driving habits. Extreme outside temperatures tend to reduce range, because more energy must be used to heat or cool the cabin. High driving speeds reduce range because of the energy required to overcome increased drag. Compared with gradual acceleration, rapid acceleration reduces range. Additional devices significant inclines also reduces range. Based on these driving modes and climate conditions, this paper discusses the performance characteristics of EVs on energy efficiency and driving range. Test vehicles were divided by low / high-speed EVs. The difference of test vehicles are on the vehicle speed and size. Low-speed EVs is a denomination for battery EVs that are legally limited to roads with posted speed limits as high as 72 km/h depending on the particular laws, usually are built to have a top speed of 60 km/h, and have a maximum loaded weight of 1,400 kg. Each vehicle test was performed according to the driving modes and test temperature ($-25^{\circ}C{\sim}35^{\circ}C$). It has a great influence on fuel efficiency amd driving distance according to test temperature conditions.

• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.114-123
• /
• 2018

As recognizing the necessity of eco-friendly vehicles in order to reduce air pollution from road sector, Korean government has established and implemented a promotion policy which is encouraging the public transportation companies to purchase CNG buses in replacing diesel buses since 2000s. With CNG bus promotion policy, the number of CNG buses had been increased on the road of metropolitan area and big cities. However, increasing rate of CNG buses had been fluctuated between the decrease and the increase since year 2014. In this study, the impact of fuel cost competitiveness between diesel and CNG on CNG bus increasing volume was testified by simple regression, which was only assumed by precedent research on the CNG promotion policy. And this study suggested the necessity of harmonization among the related policies conducted by related Ministries. Eventually this study should contribute to enhance the validity of CNG bus promotion policy. And it is expected that Korean government should apply the new policy suggestion of this study in the establishment of government's promotion policy on LNG cargo trucks and Zero Emission Vehicles in the future.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.937-944
• /
• 2022

Electric vehicles (EVs) have been growing to reduce energy consumption and greenhouse gas (GHG) emissions in the transportation sector. The increasing number of EVs requires adequate recharging infrastructure, and at the same time, adopts low- or zero-emission electricity production because the GHG emissions are highly dependent on primary sources of electricity production. Although previous research has studied solar photovoltaic (PV) -integrated EV charging stations, it is challenging to optimize spatial areas between where the charging stations are required and where the renewable energy sources (i.e., solar photovoltaic (PV)) are accessible. Therefore, the primary objective of this research is to support decisions of siting EV charging stations using a spatial data clustering method integrated with Geographic Information System (GIS). This research explores spatial relationships of PV power outputs (i.e., supply) and traffic flow (i.e., demand) and tests a community in the state of Indiana, USA for optimal sitting of EV charging stations. Under the assumption that EV charging stations should be placed where the potential electricity production and traffic flow are high to match supply and demand, this research identified three areas for installing EV charging stations powered by rooftop PV in the study area. The proposed strategies will drive the transition of existing energy infrastructure into decentralized power systems. This research will ultimately contribute to enhancing economic efficiency and environmental sustainability by enabling significant reductions in electricity distribution loss and GHG emissions driven by transportation energy.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.133-138
• /
• 2009

The continued rise in the number of automobiles on the roads is prompting air pollution to emerge as a serious problem due to the harmful exhaust gas emissions throughout the world. Specifically, based on the exhaust gas regulation in North America represented by PZEV, the regulation on evaporative emission, which originates from the intake manifold system when the engine is stopped, is substantially being intensified. And the technology that can meet and satisfy these regulations has been needed. This study aimed to analyze and evaluate the butane working capacity (BWC) of HC adsorption filter according to the shape of it, which was developed to reduce evaporative emission, and the effect of HC adsorption filter on the engine performance. As a results, HC adsorption filter of the plate type, which was improved compared to that of the corrugated type and also became thinner, indicates higher absorption performance compared to the corrugated one. The absorption performance of the honeycomb type, derived from improving the shape of plate type, is 33.5% higher than that of the corrugated type. However, there was no significant difference in engine performance in all shapes.