• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권12호
• /
• pp.632-640
• /
• 2003

In conventional Zero-Voltage-Transition(ZVT) PWM converters, zero-voltage turn-on and turn-off for main switch without increasing voltage/current stresses is achieved at a fixed frequency. The switching loss, stress, and noise, however, can't be minimized because they adopt auxiliary switches turned off under hard-switching condition. In this paper, new ZVS-PWM converters of which both active and passive switches are always operating with soft-switching condition are proposed. Therefore, the proposed ZVS-PWM converters are most suitable for avionics applications requiring high-power density. Breadboarded ZVS-PWM boost converters using power MOSFET are constructed to verify theoretical analysis.

• Journal of Power Electronics
• /
• 제14권2호
• /
• pp.237-248
• /
• 2014

Pulse-width modulated (PWM) full-bridge boost converters are used in applications where the output voltage is considerably higher than the input voltage. Zero-voltage-switching (ZVS) is typically implemented in these converters. A new ZVS-PWM full-bridge converter is proposed in this paper. The proposed converter does not have any of the disadvantages associated with other converters of this type, including a complicated auxiliary circuit, increased current stresses in the main power switches, and load-dependent ZVS operation. The operation of the proposed converter, its steady-state characteristics, and its design are explained and examined. The feasibility of the converter is confirmed with results obtained from an experimental prototype.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.988-991
• /
• 1992

A new zero voltage switching PWN converter family is presented by using a new ZVS PWN module (ZPM) with a saturable inductor which prevents diode junction capacitors and a commutation inductor from resonating. The new converters show almost all characteristics of the conventional PWN converters. A boost ZVS PWN converter is applied to a power factor correction circuit. It operates on an continuous conduction mode. Experimental results for output power of 1kW are presented.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.35-50
• /
• 2008

A zero-voltage-transition (ZVT) pulse width modulated (PWM) converter is a PWM converter with a single main power switch that has an auxiliary circuit to help it turn on with zero-voltage switching (ZVS). There have been many ZVT-PWM converters proposed in the literature as they are the most popular type of ZVS-PWM converters. In this paper, the properties and characteristics of several types of ZVT-PWM converters are reviewed. A new type of ZVT-PWM converter is then introduced, and the operation of a sample converter of this type is explained and analyzed in detail. A procedure for the design of the converter is presented and demonstrated experimentally. The feasibility of the new converter is confirmed with results obtained from an experimental prototype. Conclusions on the performance of ZVT-PWM converters in general are made based on the efficiency results obtained from the experimental prototypes of various ZVT-PWM converters of different types.

• 조명전기설비학회논문지
• /
• 제15권6호
• /
• pp.49-57
• /
• 2001

본 논문에서는 single-stage, two-stage 두가지 역률보상(PFC)기법을 기존의 능동 클램프 플라이백 컨버터에 적용하여 역률개선을 하였다. 삽입된 플라이백 컨버터의 능동클램프회로가 주스위치와 보조스위치의 영전압스위칭(ZVS)을 구현하며, 스위칭 손실을 줄임으로써 고효율을 얻을 수 있고, 높은 주파수에서의 스위칭이 가능하다. 하지만 일반적으로 사용되는 다이오드정류기, 평활용커패시터에 의한 낮은 역률의 문제점이 남아있다. 본 논문에서는 300[W급] 능동 클램프 ZVS 플라이백 컨버터를 설계하여 single-stage two-stage방식을 적용, 입력역률개선을 시뮬레이션과 실험에 의해 입증하고자 한다.

• Journal of Power Electronics
• /
• 제12권2호
• /
• pp.258-267
• /
• 2012

An interleaved single-stage AC/DC converter with a boost converter and an asymmetrical half-bridge topology is presented to achieve power factor correction, zero voltage switching (ZVS) and load voltage regulation. Asymmetric pulse-width modulation (PWM) is adopted to achieve ZVS turn-on for all of the switches and to increase circuit efficiency. Two ZVS half-bridge converters with interleaved PWM are connected in parallel to reduce the ripple current at input and output sides, to control the output voltage at a desired value and to achieve load current sharing. A center-tapped rectifier is adopted at the secondary side of the transformers to achieve full-wave rectification. The boost converter is operated in discontinuous conduction mode (DCM) to automatically draw a sinusoidal line current from an AC source with a high power factor and a low current distortion. Finally, a 240W converter with the proposed topology has been implemented to verify the performance and feasibility of the proposed converter.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1639-1649
• /
• 2016

This paper presents a family of soft-switching DC-DC converters with a simple auxiliary circuit consisting of a coupled winding and a pair of auxiliary switch and diode. The auxiliary circuit is activated in a short interval and thus the circulating conduction losses are small. With the auxiliary circuit, zero-voltage-switching (ZVS) and zero-current-switching are achieved for the main and auxiliary switches respectively, over wide input voltage range and load variation. In addition, the reverse-recovery problem of diodes is significantly alleviated because of the leakage inductor. Furthermore, the coupled inductor simultaneously serves as the main and auxiliary inductors, contributing to reduced magnetic component in comparison with the conventional zero-voltage-transition (ZVT) converters. Experimental results based on a 500 W prototype buck circuit validate the advantages and effectiveness of the proposed magnetic coupling ZVS converter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.1860-1862
• /
• 1998

This Paper presents a novel resonant switching Watkins-Johnson DC-DC converters. In the proposed converters, the basic steady-state analysis of the have been presented for the ZVS type Watkins-Johnson converter. From the results, it is shown that the output voltage of the converter is independant of load resistance, and is determined only by the switching frequency. Consequently, a design procedure is presented that minimizes voltage stress to the switch while maintaining ZVS for all loads.

• Journal of Power Electronics
• /
• 제17권4호
• /
• pp.905-913
• /
• 2017

To enhance the zero-voltage switching (ZVS) range and power density of the phase-shift full-bridge (PSFB) ZVS converters used in geophysical exploration, an additional resonant inductor is used as a leakage inductance and a blocking capacitor which is equivalent to interlayer capacitance is integrated into a novel integrated inductor-capacitor-transformer (L-C-T). The leakage inductance and equivalent interlayer capacitance of the novel integrated L-C-T are difficult to determine by conventional methods. To address this issue, this paper presents accurate and efficient methods to compute the leakage inductance and equivalent interlayer capacitance. Moreover, the accuracy of this methodology, which is based on electromagnetic energy and Lebedev's method, is verified by an experimental analysis and a finite element analysis (FEA). Taking the problems of the novel integrated L-C-T into consideration, the losses of the integrated L-C-T are analyzed and the temperature rise of the integrated L-C-T is determined by FEA. Finally, a PSFB ZVS converter prototype with the novel integrated L-C-T is designed and tested.

• Journal of Power Electronics
• /
• 제15권3호
• /
• pp.652-659
• /
• 2015

This paper presents a new hybrid soft switching dc-dc converter with a low circulating current and high circuit efficiency. The proposed hybrid converter includes two sub-converters sharing two power switches. One is a three-level PWM converter and the other is a LLC converter. The LLC converter and the three-level converter share the lagging-leg switches and extend the zero-voltage switching (ZVS) range of the lagging-leg switches from nearly zero to full load since the LLC converter can be operated at f_sw (switching frequency) $\approx$ f_r (series resonant frequency). A passive snubber is used on the secondary side of the three-level converter to decrease the circulating current on the primary side, especially at high input voltage and full load conditions. Thus, the conduction losses due to the circulating current are reduced. The output sides of the two converters are connected in series. Energy can be transferred from the input voltage to the output load within the whole switching period. Finally, the effectiveness of the proposed converter is verified by experiments with a 1.44kW prototype circuit.