• Korean Journal of Soil Science and Fertilizer
• /
• v.49 no.1
• /
• pp.7-11
• /
• 2016

Winter crops have been recognized as an alternative to soil management for fertility and crop productivity in paddy soil. Recently, rape has been produced at winter season and there is little research results on reduction of N fertilizer by adding rape residues for rice cultivation. In this study, we investigated the productivity and quality of rice by applying with 0, 27, 63, $90kg\;ha^{-1}$ of N fertilizer after input of rape residues into soil for two years. The highest yield of rice was average $4.68Mg\;ha^{-1}$ at the treatment applied with the $90kg\;N\;ha^{-1}$ with rape residue. It was reduced to N rate from 31.6 to $43.2kg\;N\;ha^{-1}$ in comparison to $4.53Mg\;ha^{-1}$ of maximum yield in treatment added $90kg\;N\;ha^{-1}$ with rape. Amylose content in rice was similar among treatments with/without rape residue, but protein content was lower in treatment with rape residue than in those without rape residue. In conclusion, input of rape residue in rice cultivation could be alternative to reduction of N fertilization and improvement of quality by adjusting rice productivity in paddy soil under cropping system.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.19 no.1
• /
• pp.165-169
• /
• 2009

A field experiment to evaluate the effect of application of different organic manures and inorganic fertilizers on growth, yield and quality of leaf was studied during 2004-05 has showed that, the application of 10 kg each of Azospirillum brasilense and Aspergillus awamori+20% each of recommended N through compost+green manure (Glyricidia maculata)+castor cake+vermicompost+Urea and remaining P and K through fertilizers ($T_{11}$) has recorded significantly higher leaf yield (250 g/ plant and 34.70 tonnes/ha/yr, respectively) with improvement in growth characters as compared to control. Leaf quality status was also improved in terms of N (3.19%), P (1.97%), K (1.28%), total soluble protein (8.39 mg/ml), total soluble sugars (14.40 mg/ml), secondary nutrients viz., Ca (3.00%), Mg (0.60%), S (0.35%) and micronutrients viz., Cu (0.410 ppm), Mn (0.454 ppm) and Zn (0.112 ppm) contents. The mulberry grown with 20 tonnes of compost+300:120:120 Kg of NPK/ha/year through fertilizer ranked second for growth and foliar constituents.

• Journal of Microbiology
• /
• v.40 no.1
• /
• pp.82-85
• /
• 2002

The aerobic batch growth of Issatchenkia orientalis DY252 with glucose and fructose medium was investigated at 32$\^{C}$ and pH 5.0. Aerobic ethanol production was evident with yeast I, orientalis. A diauxic lag of about 1 h between growth on glucose and growth on ethanol during batch culture was observed. However, no diauxic growth occurred with fructose. As the incubation temperature was increased from 32 to 39$\^{C}$, viability at the end of each batch culture declined significantly, from 93 to 43%, Unlike the effect of temperature, viability was not greatly affected by incubation pH, and cell yield values in a range of 0.45-0.48 were obtained. In order to overcome overflow metabolism, a fedbatch culture under glucose limitation was carried out. Compared with aerobic batch culture, about 10% improvement in cell yield was achieved with a fed-batch culture in optimal conditions.

• The Korean Journal of Mycology
• /
• v.20 no.1
• /
• pp.77-82
• /
• 1992

Researches were carried out to find the optimal conditions of carbon sources, nitrogen sources and pH for the maximum production of sporophore of Lentinus edodes. Dextrin, aspartic acid and pH 4.0 were the best conditions for yield of sporophore by using replacement culture technique. The production of sporophore was stimulated by addition of 0.8% triacylglycerol in NS medium. Coffee waste was chosen for the best substrate among the poplar, oak, white aspen saw dust and coffee waste. Increased growth of mycelim and yield of sporophore was obsewed by adding tannin up to 0.1% as substrate.

• Mycobiology
• /
• v.39 no.1
• /
• pp.20-25
• /
• 2011

Spores of Aspergillus sp. SU14 were treated repeatedly and sequentially with $Co^{60}$ ${\gamma}$-rays, ultraviolet irradiation, and N-methyl-N'-nitro-N-nitrosoguanidine. One selected mutant strain, Aspergillus sp. SU14-M15, produced cellulase in a yield 2.2-fold exceeding that of the wild type. Optimal conditions for the production of cellulase by the mutant fungal strain using solid-state fermentation were examined. The medium consisted of wheat-bran supplemented with 1% (w/w) urea or $NH_4Cl$, 1% (w/w) rice starch, 2.5 mM $MgCl_2$, and 0.05% (v/w) Tween 80. Optimal moisture content and initial pH was 50% (v/w) and 3.5, respectively, and optimal aeration area was 3/100 (inoculated wheat bran/container). The medium was inoculated with 25% 48 hr seeding culture and fermented at $35^{\circ}C$ for 3 days. The resulting cellulase yield was 8.5-fold more than that of the wild type strain grown on the basal wheat bran medium.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.2
• /
• pp.81-88
• /
• 2020

The damping hinge of a built-in refrigerator was examined in terms of its stress and fatigue life. Analysis of the initial design showed that stress concentration occurred at the concave surface of the hinge lever, which was broken during the door opening-and-closing endurance test of the prototype. The maximum von Mises stress at this location exceeded the yield strength. In addition, Goodman fatigue analysis of the initial design showed that the fatigue life at this location was consistent with the failure observed during the endurance test. Based on these results, an improved design for the damping hinge was derived. Analysis of this improved design showed that the stress concentration in the hinge lever of the initial design was eliminated. In this case, the maximum stress occurred at the position where the hinge lever was in contact with the door stopping pin, and the maximum von Mises stress was smaller than the yield strength. Goodman fatigue analysis of the improved design indicated that the fatigue life of the entire damping hinge was infinite. It was therefore concluded that the improved design does not suffer from fatigue damage during the endurance test.

• Nuclear Medicine and Molecular Imaging
• /
• v.43 no.1
• /
• pp.1-9
• /
• 2009

As many new drug substances contained various aromatic rings and fluorine attached to an electron rich aromatic ring or on the meta-position, a strategy towards improvement in aromatic fluorination of these compounds is highly desirable. The introduction of fluorine-18 onto aromatic rings showed in the limited condition containing electron withdrawing group (EWG) on the para- or ortho-position to get reasonable radiochemical yield so far. No-carrier added (NCA) [$^{18}F$]fluoroarene syntheses by iodonium salts recently reported that has the potential to greatly increase the yield in systems or positions that normally not reactive enough to give sufficient yields in simple model reaction. This review describes the methodological approach towards effective aromatic fluorination by diaryliodonium salts and future prospects in an application of novel PET radiotracer.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.26 no.3
• /
• pp.273-277
• /
• 1981

This study was carried out in 1979 to establish the proper mulching culture method for an aromatic tobacco, ST 375-4. Three different methods of mulching were employed: Improved mulching (I. M.), General mulching (G. M.) and Non-mulching (N. M.). The number of seedlings per hole was 5 for I. M., and one for G. M. and N. M. In comparison with N. M., I. M. had shortened final date of leaf harvest by 14 days, enabling curing leaves before the rainy season. It also reduced transplanting labour hours by 44.9%. Yield and price value increased with improved mulching culture. There was little difference in relative light intensity at leaves between N. M. and I. M.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.13-13
• /
• 2017

By the progress of genome sequencing, infrastructures for marker-assisted breeding (MAB) of rice came to be established. Fine mapping and gene isolation have been conducted using the breeding materials derived from natural variations and artificial mutants. Such genetic analysis by the genome-wide dense markers provided us the knowledge about the many genes controlling important traits. We identified several genes or quantitative trait loci (QTL) for heading date, blast resistance, eating quality, high-temperature stress tolerance, and so on. NILs of each gene controlling heading date contribute to elongate the rice harvest period. Determination of precise gene location of blast resistance gene pi21, allowed us to overcome linkage drag, co-introduction of undesirable eating quality. We could also breed the first practical rice cultivar in Japan with a brown planthopper resistance gene bph11 in the genetic back-ground of an elite cultivar. Discovery of major and minor QTLs for good eating quality allowed us to fine-tune of eating quality according to the rice planting area or usage of rice grain. Many rice cultivars have bred efficiently by MAB for several traits, or by marker-assisted backcross breeding through chromosome segment substitution lines (CSSLs) using genetically diverse accessions. We are also systematically supporting the crop breeding of other sectors by MAB or by providing resources such as CSSLs. It is possible to pyramid many genes for important traits by using MAB, but is still difficult to improve the yielding ability. We are performing a Genomic Selection (GS) for improvement of rice biomass and grain yield. We are also trying to apply the genome editing technology for high yield rice breeding.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.45-52
• /
• 2004

Continuing pressure for the weight reduction of vehicles and improvement of collision safety is driving the development of new high strength steel with excellent formability. The formable high strength steels which have excellent drawability have been developed and applied to the complicated inner panels. Although BH steel have mainly occupied the material market for outer panels, it is challenged by DP steel which have low yield strength and good bake hardenability. The advanced high strength steel, TRIP steels and DP steels which have excellent formability are new alternatives to conventional HSLA steel for structural parts such as members and pillars. HSLA steels also have been used for automotive bumper reinforcements due to their high yield ratio. Higher grade complex phase steel(CP) were developed for bumper reinforcements by addition of precipitation hardening to transformation strengthened steel. The usage of the advanced high strength steel ale increasing and will become the main material in structural parts near future. This paper describes the features of newly developed high strength cold rolled steels for automobiles.