• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.10a
• /
• pp.125-132
• /
• 1998

In this study the fire, due to overturning of oil tanker on the bridge induced heat transfer analysis and thermal stress analysis are carried out. The results of analysis for fire history of 1 hour present very large thermal gradient near the surface. However, the temperature increase of tendon & rebar that is the main resistant member of bridge is not sufficient to change material properties. The Von-Mises yield criteria is used to calculate the depth of delamination, The depth of delamination is about 4cm at center of fire and this value is close to measured value.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.1
• /
• pp.5-14
• /
• 2019

The objective of this study was investigated the effect of organic fertilizer(OF) application on the grain yield, protein content, and soil chemical properties in rice cultivation to evaluate the replacement ratio of OF based on basal fertilization of inorganic(nitrogen) fertilizer, In case of soil 1 with optimum range of organic matter for rice growth, the grain yield of rice in 70% and 100% treatments of OF were higher than the other treatments. In soil 2 with higher than the optimum range of soil organic matter, the grain yield of rice of NPK, 30%, 70%, 100%, and 300% treatments of OF showed no significant difference. When the protein criteria of rice quality was below 7%, the treatment of 30%, 70%, and 100% using OF in soil 1 were satisfied with protein criteria of rice. In case of soil 1, ammonium nitrogen content, electrical conductivity, and the organic matter in 30%, 70%, 100%, 300% treatments of OF showed similar tendency to NPK treatment. These results suggested that the substitution ratio of OF 70~100% could be appropriate to increase the yield and commercial quality for rice.

• Journal of Bio-Environment Control
• /
• v.11 no.1
• /
• pp.12-17
• /
• 2002

Tn establish the criteria for appropriate seedling production method in the summer, the effect of container size and seedling age on the growth and yield were evaluated with tomato. The seedling quality was higher when seedlings were grown polyethylene in 9cm pots than in 72 cell plugs. Seedling quality increased with increase in seedling age in polyethylene pots, whereas seedling age did not affect seedling quality in plug trays. Fruits matured earlier on plants started from pot-grown transplants for a long duration than with plug tray-grown transplants for a shorter duration. Not only total yield in 4 months, but the early yield in the first 2 months, was higher with pot-nursed transplants than with plug tray-nursed transplants. With pot-grown transplants, The early yield in initial 2 months was the lowest in 25 day-old transplants, whereas there was no significant differences between 35- and 45-day-old transplants. Seedling age did not affect the cumulative yield for 3 months after the first harvest. With plug tray-grown transplants, the cumulative yield tar initial 3 months was the highest in plants grown for 35 days in the nursery, followed by 25 day and 45 day. However, there were no significant differences among seedling ages in the total yield.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.278-278
• /
• 2022

Recently, the yield potential of high yield Tongil-type rice varieties has greatly increased, reaching 817kg/10a(Geumgang No.1). Moreover, in order to promote rice consumption and strengthen the competitiveness of the rice processing industry, the R&D of high yield Tongil-type rice varieties for each processing purpose, such as rice noodles, grain feed and industrial materials, has been continuously carried out. However, because Tongil-type rice varieties or lines are generally very vulnerable to cold damage, cold tolerance test can be said to be absolutely necessary to improve the cultivation safety. This study is the result of the seedling and field cold tolerance characteristic tests carried out in 2021 of high yield Tongil-type rice breeding lines. For the cold tolerance characteristic test of seedlings, total 303 high yield rice breeding lines for processing were treated in cold water of 13℃ and irrigation depth of 4cm for 10 days from the third-leaf age, then it was evaluated by comparing the degree of discoloration and withering with the checked varieties(Boramchan, Hanahreum No.2). Also, for the test of field, total 186 high yield rice breeding lines for processing were treated in cold water of 17℃ by keeping pouring day and night from 30 days after transplanting to ripening stage, then it was evaluated by comparing the degree of discoloration, delay of heading, shortening rate of stem length and percent of fertile grain etc. with the checked varieties. And the cold tolerance evaluative criteria were classified as strong(1~3), medium(4~6) and weak(7~9) in overall cold tolerance. (Seedling test) As for the degree of cold tolerance of the check variety, 'Boramchan' and 'Hanahreum No.2' showed a response of 'medium' and 'weak', respectively. However, there was no 'strong' line in the high yield rice breeding lines, 2 lines showed a 'medium' response, and 301 lines showed a 'weak' response. Therefore, except for a few lines(0.7%), most lines(99.3%) showed a 'weak' response. (Field test) In terms of the overall cold tolerance of the check variety, both 'Boramchan' and 'Hanahreum No.2' showed a 'medium' response. Similarly, there was no 'strong' line in the case of high yield rice breeding lines, 20 lines showed a 'medium' response, and 166 lines showed a 'weak' response. Therefore, except for some(10.8%) lines, most(89.2%) lines showed a 'weak' response. From the above results, we selected about 100 individuals with less seed shattering and degeneration of the ear tip, and with a relatively high percent of fertile grain, and are continuing to select lines with improved cold tolerance in the F4~F5 group in this year. As such, most of the Tongil-type rice varieties have poor cold tolerance and thus have low cultivation safety at low temperatures. However, it is important to select improved lines through generational progress because there are some lines that still have a certain level of cold tolerance among them.

• Korean Journal of Soil Science and Fertilizer
• /
• v.46 no.6
• /
• pp.542-548
• /
• 2013

Soil properties and yields of liriopis platyphylla were investigated to establish soil suitability of Korean liriopis platyphylla at 116 farms in Korea. Morphological and physical properties of the soils were investigated along with the average yield of 2~3 years. The impact factors of soil properties to the yield of liriopis platyphylla were selected based on standard error of each factor. The yields of liriopis platyphylla showed the greatest values when the morphology was alluvial plains, when the drainage was well or moderately well, when the slope was 0-2%, the texture was coarse loamy, when the gravel content was less than 15% and when the available soil depth was more than 100 cm. Contribution factors of soil properties to the yields were 0.15 by morphology, 0.15 by drainage level, 0.13 by slope, 0.18 by texture, 0.16 by gravel content and 0.23 by available soil depth, respectively. Soil suitability classes were set as follows; the best suitable land if score was greater than 92, suitable land if score ranged from 91 to 86, the possible land if the score ranged from 85 to 83, and low productive land if score was less than 82. According to the criteria, 17.8% of the production area was the best suitable land, 43.1% was suitable land, 17.3% was possible land, and 21.8% was low productive land. The sum of both the best and suitable lands were 60.9% of the farm area of Miryang in Gyeongsangnam-do.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.6
• /
• pp.47-54
• /
• 2001

Unbond brace hysteretic dampers are generally used to prevent or decrease structural damage in building structures subjected to strong earthquake by its energy dissipating hysteretic behavior. In the study, a straightforward design procedure for unbond brace hysteretic dampers was developed. The required amount of equivalent damping to satisfy given performance acceptance criteria was obtained conveniently based on the capacity spectrum method without carrying out time-consuming nonlinear dynamic time history analysis. Then the size of the unbond braces is determined from the required equivalent damping. Parametric study has been performed for the design variables such as natural period, yield strength, the stiffness after the first yield stress of the unbond brace. The procedure was applied to 5-story and 10-story steel frames for verification of the proposed method. According to the earthquake time history analysis results, the maximum displacement of the model structure with unbond braces supplied in accordance with the proposed method corresponds well with the given target displacement.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.5
• /
• pp.151-159
• /
• 2000

Dynamic loading of structures often causes excursions of stresses will into the inelastic range and the influence of geometry changes on the response is also significant in may cases. In general , the shell structures designed according to quasi-Static analysis may collapse under condition of dynamic loading. Therefore, for a more realistic prediction on the lad carrying capacity of these shell. both material and geometric nonlinear effects should be considered. In this study , the material nonlinearity effect on the dynamic response is formulated by the elasto-viscoplastic model highly corresponding to the real behavior of the material. Also, the geometrically nonlinear behavior is taken into account using a Total Lagrangian formulation. the reinforcing bars are modeled by the equivalent steel layer at the location of reinforcements, and Von Mises yield criteria is adopted for the steel layer behavior. Also, Drucker-Prager yield criteria is applied for the behavior of concrete. the shape imperfection of dome is assumed as 'dimple type' which can be expressed Wd1=Wd0(1-(r-a)m)n while the shape imperfection of wall is assumed as sinusoidal curve which is Wwi =Wwo sin(n $\pi$y/l). In numerical test, three cases of shape imperfection of 0.0 -5.0cm(opposite direction to loading ; inner shape imperfection)and 5cm (direction to loading : outward shape imperfection) and thickness of steel layer determined by steel ratio of 0,3, and 5% were analyzed. The effect of shape imperfection and steel ratio and behavior characteristics of perfect shape shell and imperfect shape shell are identified through analysis of above mentioned numerical test. Dynamic behaviors of dome and wall according toe combination of shape imperfection and steel ratio are also discussed in this paper.

• International Journal of High-Rise Buildings
• /
• v.6 no.3
• /
• pp.249-259
• /
• 2017

The use of high-strength steels in construction of highrise and mega building structures can bring about many technological advantages from fabrication to erection. However, key design criteria such as local and lateral stability in current steel design specifications were developed based on tests of ordinary steels which have stress-strain characteristics very different from that of high strength steels. A series of tests on 800 MPa tensile strength steel (HSA800) members are summarized in this paper which were conducted to investigate the appropriateness of extrapolating current ordinary-steel based design criteria to high strength steels. 800 MPa I-shape beam specimens designed according to flange local buckling (FLB) criteria of the AISC Specification developed a sufficient strength for elastic design and a marginal rotation capacity for plastic design. It is shown that, without introducing distinct and significant yield plateau to the stress-strain property of high-strength steel, it is inherently difficult to achieve a high rotation capacity even if all the current stability limits are met. 800 MPa I-shape beam specimens with both low and high warping rigidity exhibited sufficient lateral torsional buckling (LTB) strength. HSA800 short-column specimens with various edge restraint exhibited sufficient local buckling strength under uniform compression and generally outperformed ordinary steel specimens. The experimental P-M strength was much higher than the AISC nominal P-M strength. The measured residual stresses indicated that the impact of residual stress on inelastic buckling of high-strength steel is less. Cyclic seismic test results showed that HSA800 members have the potential to be used as non-ductile members or members with limited ductility demand in seismic load resisting systems. Finally, recent applications of 800 MPa high strength steel to highrise and mega building structures in Korea are briefly presented.

• Journal of Pharmacopuncture
• /
• v.12 no.4
• /
• pp.33-50
• /
• 2009

Objectives : This study was conducted to confirm validation and stability of concentration analysis method of pure melittin (Sweet Bee Venom-Sweet BV) extracted from the bee venom by utilizing protein isolation method of gel filtration. Methods : All experiments were conducted at Biotoxtech, a non-clinical studies authorized institution, under the regulations of Good Laboratory Practice (GLP). Standard solutions of melittin (SIGMA, USA) and test substances were dispensed and were analyzed with HPLC for Sweet BV to secure the validation of analysis. Results : 1. Measurement of system suitability of Sweet BV satisfied criterion of below 3%. 2. Confirming Linearity of Sweet BV in 10-200${\mu}g/m\ell$ solution yielded correlation coefficient (r) of 0.995 and accuracy of 85-115% which satisfy criterion. 3. Measurement of Specificity of Sweet BV didn't yield any substance affecting the peak of test substances, but detected at 21.22min verified as the test substance. 4. Confirming Intra-day of Sweet BV, accuracy and precision of 0.1, 100${\mu}g/m\ell$ were 105.70, 95.81 and 0.66, 0.73, respectively, satisfying both criteria of accuracy (85-115%) and precision (within 10%). 5. To measure Stability in autosampler, all samples used in Intra-day reproducibility sat in the autosampler for five hours and were re-analyzed. Both variability and precision satisfied the criteria. 6. Homogeneity of Sweet BV (0.1, 100${\mu}g/m\ell$) at upper, middle, and lower layers all satisfied the accuracy and precision criteria. 7. Stability of Sweet BV (0.1, 100${\mu}g/m\ell$) at room temperature for four hours and refrigerated for 7 days all satisfied the criterion. 8. For the measurement of Quality control, QC samples measured on the first and eighth day all satisfied accuracy and precision criteria. Conclusion : Above experiment data satisfies validation and stability of concentration analysis method of Sweet BV.

• Journal of Computational Design and Engineering
• /
• v.3 no.1
• /
• pp.37-52
• /
• 2016

To injection mould polymers, designing mould is a key task involving several critical decisions with direct implications to yield quality, productivity and frugality. One prominent decision among them is specifying sprue-bush conduit expansion as it significantly influences overall injection moulding; abstruseness anguish in its design criteria deceives direct determination. Intuitively designers decide it wisely and then exasperate by optimising or manipulating processing parameters. To overwhelm that anomaly this research aims at proposing an ideal design criteria holistically for all polymeric materials also tend as a functional assessment metric towards perfection i.e., criteria to specify sprue conduit size before mould development. Accordingly, a priori analytical criterion was deduced quantitatively as expansion ratio from ubiquitous empirical relationships specifically a.k.a an exclusive expansion angle imperatively configured for injectant properties. Its computational intelligence advantage was leveraged to augment functionality of perfectly injecting into an impression gap, while synchronising both injector capacity and desired moulding features. For comprehensiveness, it was continuously sensitised over infinite scale as an explicit factor dependent on in-situ spatio-temporal injectant state perplexity with discrete slope and altitude for each polymeric character. In which congregant ranges of apparent viscosity and shear thinning index were conceived to characteristically assort most thermoplastics. Thereon results accorded aggressive conduit expansion widening for viscous incrust, while a very aggressive narrowing for shear thinning encrust; among them apparent viscosity had relative dominance. This important rationale would certainly form a priori design basis as well diagnose filling issues causing several defects. Like this the proposed generic design criteria, being simple would immensely benefit mould designers besides serve as an inexpensive preventive cliché to moulders. Its adaption ease to practice manifests a hope of injection moulding extremely alluring polymers. Therefore, we concluded that appreciating injectant's polymeric character to design exclusive sprue bush offers a definite a priori advantage.