• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.745-750
• /
• 2000

YAG:Tb3+ as green phosphor were studied for the development of low voltage FED phosphor prepared by hydrothermal synthesis. We changed the concentration of luminescence center ion Tb3+ in hydrothermal reaction of which conditions were at 8M NH4OH as mineralizer, at 35$0^{\circ}C$ for 12hrs. As results, we could finally get the YAG:Tb3+ (Y3-xTbxAl5O12) powder of which particle size was about 0.2~1.0${\mu}{\textrm}{m}$. The excitation spectra and the green emitted spectra of YAG:Tb3+ phosphor powder were observed. When we doped 0.25 mol Tb to YAG, we could observe the maximum cathodoluminescence from YAG:Tb3+ phosphor and the chromaticity coordinate of the phosphor was shown x=0.35, y=0.56 in CIE1931 diagram.

• Journal of Powder Materials
• /
• v.19 no.3
• /
• pp.220-225
• /
• 2012

YAG:Ce yellow phosphor particles were synthesized by spray pyrolysis with changing the solution properties and their luminous properties, crystal structure, and morphological changes were studied by using PL measurement, XRD, and SEM analysis. It was clear that the solution properties significantly affected the crystal phase, crystallite size, the PL intensity, and the morphology of YAG:Ce particles. At low calcination temperature, the addition of urea only to the spray solution was helpful to form a pure YAG phase without any impurity phases, as the result, the highest luminescence intensity was achieved at the calcination temperature of $900^{\circ}C$. When the calcination temperatures were larger than $1300^{\circ}C$, however, the YAG particles prepared without any additive showed the highest luminescent intensity. Regardless of the solution conditions, the emission intensity of YAG:Ce particles prepared by spray pyrolysis showed a linear relation with the crystallite size. In terms of the morphology of YAG:Ce particles, the addition of both DCCA and $NH_4OH$ to the spray solution was effective to prepare a spherical and dense structured YAG particles.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1120-1126
• /
• 2003

Yttrium Aluminum Garnet (YAG) powders were prepared by precipitation of Y hydroxides during milling of alumina powders. The powder calcined at 1200$^{\circ}C$ for 4 h contained a small amount of Yttrium Aluminum Monoclinic (YAM) in addition to YAG. However, phase-pure YAG was obtained in the compact of the milled powder with an average particle size of 0.57 ${\mu}$m at 1300$^{\circ}C$, which is much lower than those (l500∼1600$^{\circ}C$) for a mixed oxide method. The powder was found to exhibit an excellent sinterability regardless of the addition of a sintering aid, SiO$_2$(350 ppm Si). The undoped sample were sintered to a relative density of 98% at l600$^{\circ}C$. In contrast, the addition of SiO$_2$ caused a considerable densification to occur at 1500$^{\circ}C$ and the relative density reached 97.7%. But the sintering aid had little effect on the densification at 1600$^{\circ}C$, showing a similar relative density to the undoped sample.

• Journal of Welding and Joining
• /
• v.25 no.4
• /
• pp.49-57
• /
• 2007

The optimization of the cladding parameters was studied to maximize the deposition efficiency in the laser cladding using a low power pulsed Nd:YAG laser. STS304 stainless steel plate and Co alloy powder were used as a substrate and powder for cladding, respectively. The six cladding parameters were selected through preliminary experiments and their effects on the deposition efficiency were analyzed statistically. Experiments were designed and carried out using the Taguchi experimental method using a L18 orthogonal array. It was found from the results of analysis of variance(ANOVA) that the powder feed position and powder feed angle had the most significant effects on the deposition efficiency, but the powder feed rate and laser focal position had nearly no effects. The deposition efficiency could be maximized at 0mm of the powder feed position and 50o of the powder feed angle in the experimental range. From this experimental analysis, a new laser cladding head with 20o of the powder feed angle was designed and manufactured. With a new laser cladding head, the highest deposition efficiency of 12.2% could be obtained.

• Journal of Powder Materials
• /
• v.13 no.4 s.57
• /
• pp.243-249
• /
• 2006

Yttrium aluminum garnet (YAG) powders were synthesized via mechanochemical solid reaction using $Y_2O_3$ with three types of aluminum compounds. $Y_2O_3$ reacted mechanochemically with all A1 compounds and formed YAM (yttrium aluminum monoclinic), YAG and YAP (yttrium aluminum perovskite) phases depending on the starting materials. The ground samples containing ${\gamma}-A1_2O_3$ showed the best reactivity, whereas the ground sample containing A100H, which had the largest surface area, exhibited pure YAG after calcination at $1200^{\circ}C$. The sample containing Al had the least reactivity, producing YAP along with YAG at $1200^{\circ}C$. The types and grinding characteristics of the starting materials and grinding time are believed to be important factors in the mechanochemical synthesis of YAG.

• Journal of the Korean Ceramic Society
• /
• v.26 no.3
• /
• pp.402-408
• /
• 1989

$\beta$-Sialon powder was synthesized by the simultaneous reduction and nitridation of the mixed powder of Hadong kaolin and Kimcheon quartzite, using graphite as a reducing agent. The synthesized $\beta$-Sialon powder (Z=1) was hot-pressed at 175$0^{\circ}C$, for 90min under 30MPa in N2 atmosphere, after Yttria and YAG composition material were added as sintering agents. The effects of grain-boundary crystallization on high-temperature mechanical properties of $\beta$-Sialon ceramics were investigated. Strength degradation was observed at above 1,00$0^{\circ}C$ for the $\beta$-Sialon (Z=1)-8wt% Y2O3 composition, but it was not observed up to 1,20$0^{\circ}C$ for the $\beta$-Sialon-8wt% YAG composition which was annealed at 1,40$0^{\circ}C$ for 4 hours in N2 atmosphere. After the $\beta$-Sialon-8wt% YAG composition was annealed, the decrease of fracture toughness was observed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.440-441
• /
• 2007

For this study, terbium-doped yttrium aluminum garnet (YAG:Tb) phosphor powders were prepared via the combustion process using the varous reagents. The characteristics of the synthesized nano powder were investigated by means of X-ray diffraction (XRD), Scanning Electron Microscope(SEM), and photoluminescence (PL). Single-phase cubic YAG:Tb crystalline powder was obtained at $1000^{\circ}C$ by directly crystallizing it from amorphous materials, as determined by XRD techniques. The SEM image showed that the resulting YAG:Tb powders had uniform sizes and good homogeneity. The photoluminescence spectra of the YAG:Tb nanoparticles were investigated to determinethe energy level of electron transition related to luminescence processes. There were three peaks in the excited spectrum, and the major one was a broad band of around 274 nm. Also, the YAG:Tb nanoparticles showed two emission peaks in the range of 450~500 nm and 525~560 nm, respectively, and had maximum intensity at 545 nm.

• Restorative Dentistry and Endodontics
• /
• v.20 no.2
• /
• pp.399-422
• /
• 1995

The purpose of this study was to investigate a fragment of possibility of pulpotomy with the Nd-YAG laser by the observation of pulpal healing process and the fine structural changes of the fibroblasts of the remaining pulpal tissues. Class V cavities on !55 teeth from 4 adult dogs were prepared and the pulp chambers were opened with a sterilized round bur. In the control group(19 teeth), the exposed coronal pulps were excised by a sharp excarvator. After bleeding was controlled with the sterilized cotton pellets, calcium hydroxide powder was applied on the remaining pulpal tissues and the cavities were sealed with Z.O.E. In the experimental group 1 : the pulpotomy with laser-calcium hydroxide powder application group(l9 teeth), the exposed coronal pulps were excised by Nd-YAG laser(10 watts power, 2 psi water, 20 psi air) for 2 or 3 seconds and calcium hydroxide powder was applied on the remaining pulpal tissues and the cavities were sealed with Z.O.E. In the experimental group 2 : the pulpotomy with laser-no calcium hydroxide powder application group(17 teeth), after amputating the coronal pulps with Nd-YAG laser as the experimental group 1, the remaining pulpal tissues were covered with stenilized aluminum foil and the cavities were filled with Z.O.E. The animals were sacrificed at the intervals of 1, 2, 3 and 4 weeks. All the teeth were rouutinely processed and the remaining pulpal tissues were observed by the light microscope and electron microscope. The results were as follows : 1. In light microscopic findings, there was no significant difference of the inflammatory response in the remaining pulpal tissues between the control group and the experimental groups. In both of the experimental group 1 : pulpotomy with laser-calcium hydroxide powder application group and the control group, the dentin bridges were observed after 2 weeks and the structure of the dentin bridge was almost same. In the experimental group 2 : pulpotomy with laser-no calcium hydroxide powder application group, the fibrous layers instead of dentin bridge were observed on the superficial portion of the remaining pulpal tissues after 2 weeks and they were consisted with densely crowded active fibroblasts. 2. In the electronmicroscopic findings, the active fibroblasts in the experimental groups were more frequently observed than in the control group at 1 week. But active fibroblasts were found with same frequency after 2 weeks in all of the control group and the experimental groups. 3. General distortions of the cell such as loss of the cell membrane, vaculoization of the cell etc. were observed at the suberficial layer of the remaining pulpal tissues and the carbonization was found in the dentinal wall in 1 week of the experimental groups. 4. In the experimental group 2 : pulpotomy with laser-no calcium hydroxide powder application group, the activity and the density of the fibroblasts in the fibrous layer were more than those in the deep portion of the remaining pulpal tissues after 2 weeks. 5. In the control group, bacteria such as cocci and bacilli were observed frequently, but in the experimntal groups, they could not be observed.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.74.2-74
• /
• 2003

• Laser Solutions
• /
• v.3 no.1
• /
• pp.21-28
• /
• 2000

Selective Laser Sintering (SLS) can produce three-dimensional objects directly from a CAD solid model without part-specific tooling. In this study, a simple rapid prototyping through selective laser sintering on brass powder is investigated using a Nd-YAG laser. Experiments are conducted to produce single lines on a powder-packed bed for various process parameters. Also, temperature distribution in the powder bed and the thickness of a melted line are predicted by finite element analysis. In the numerical analysis, the thermal conductivity of the brass powder which is obtained as a function of state and temperature is used.