• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1354-1357
• /
• 2003

Mold Analysis is crucial factors in the design of injection molding process. Since the qualify of products depends on filing, shrinkage and etc, the procedure of prediction through analysis in the design of injection molding process is needed. In many cases, this kind of analysis makes it possible to predict pressure pattern which determines the condition of injection molding process. Crystallinity is the factor that determines the shrinkage of products. The studies showed the factors that had been related to the degree of crystallinity, which were mostly Weight Reduction, mold temperature and melt temperature. Therefore, the objective of this study is to see the differences of the degree of crystallinity depending on the positions of foamed plastics. The procedure of this study is as the following. First, Simulate the pressure gradient in mold cavity that can produces specimen by using Moldflow. Secondly, produce specimen and measure the degree or crystallinity of each part of specimen by using XRD. Lastly, identify the sensitivity of conventional plastic and foamed plastic on pressure gradient by comparing the simulation and the results of measurement.

• Journal of Welding and Joining
• /
• v.28 no.1
• /
• pp.86-91
• /
• 2010

In the present study, two-dimensional plane deformation thermo elasto-plastic analysis has been carried out, in order to investigate the thermal and mechanical behaviour (residual stress, plastic strain, magnitude of stress and their distribution and production mechanism) on multi-pass FCA butt weldment of high strength EH36-TMCP ultra thick plate. Moreover, this study can be considered as a basis for analysing the fracture toughness, KIC, and its effect on welding residual stress redistribution with notch on multi-pass FCA butt weldment, in future. The results of welding residual stress obtained from thermo elasto-plastic analysis has been compared and verified with the results measured by XRD.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.25-28
• /
• 2001

The objectives of this paper are to demonstrate the electrical degradation phenomena with Si atom's behaviors in the grainboundary of semiconducting ZnO ceramics. The ZnO ceramic devices used in this investigation were fabricated by standard ceramic techniques. Especially, $SiO_2$ were added to analyze the degradation characteristics with Si and sintered in oxygen ambient at $1300^{\circ}C$. The conditions of DC degradation test were $115{\pm}2^{\circ}C$ for 13h. Using XRD and SEM, the phase and microstructure of samples were analyzed respectively. E-J analysis was used to determine $\alpha$. Frequency analysis was accomplished to understand $R_g$ and $R_b$ at the equivalent circuit. Electrical stability improved as the amount of $SiO_2$ addition increased. This results were explain by the quantitative analysis and the line scanning method of EPMA.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.5
• /
• pp.383-389
• /
• 2000

The relationship between the DC degradation characteristics of the ZnO varistor and the ambient sintering-process is investigated in this study. ZnO varistors made o matsuoka’s composition were fabricated by standard ceramic techniques. The ambient sintering-process is performed at the extraordinary electrical-furnace which is equipped with the vacuum system. Gases used in sintering process were oxygen nitrogen argon and air. Using XRD and SEM the phase and microstructure of samples were analyzed respectively. The conditions of DC degradation tests were conducted at 115$\pm$2$^{\circ}C$ for 13 h. Current-voltage analysis is used to determine nonlinear coefficients($\alpha$). Frequency analysis are performed to understand electrical properties as DC degradation test. From above analysis it is found that the ZnO varistor sintered in oxygen atmosphere showed superior properties at the DC degradation test and degradation phenomenon of ZnO varistor is caused by the change of electrical properties in grain boundary. These results are in accordance with Gupta’s degradation model.

• Journal of the Korean Ceramic Society
• /
• v.56 no.3
• /
• pp.308-316
• /
• 2019

CdS_xSe_1-x ternary alloy nanowires (x = 0, 0.5, 1.0) were fabricated by in-situ synthesis on interdigitated electrode. Morphology analysis of the alloy nanowires according to the synthesis zone and composition analysis of the nanowires were carried out by SEM and EDX. The crystal structures of the alloy nanowires were studied by XRD analysis. The I-V characteristics of the nanowire photosensors were analyzed according to the intensity of incident light. The influence of zonal synthesis position on the photosensor response to the wavelength of incident light was also analyzed, and was found to be related to the bandgap of alloy nanowires. The analysis results indicate that photosensors with a specific photoresponse could be selected based on the composition of the source materials of nanowires as well as by controlling the in-situ synthesis zone.

• Korean Journal of Metals and Materials
• /
• v.49 no.3
• /
• pp.250-255
• /
• 2011

The basic properties and electrical characteristics of sputtering films deposited with a commercial cast target and Spark Plasma Sintering (SPS) were compared and analyzed. From the results, the Cu film prepared heating $60^{\circ}C/min$ (SPS process) showed a similar specific resistance compared to the commercial cast Cu film. Also, auording to the results of XRD, SIMS, and TEM. There was not much difference in the crystal structure and impurities between the two films. Consequently, the SPS Cu target was found to have quite similar properties with the commercial one and it is expected to be applied in futare research to the metal wiring material for semiconductor/display devices.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.1
• /
• pp.52-58
• /
• 2013

In order to overcome the cost issue for commercialization of polymer electrolyte membrane fuel cell (PEMFC), this research was conducted for replacing platinum cathode catalyst with non-precious metal catalyst. The non-precious metal catalyst (Co-PANI-C) was synthesized by the simple reduction method with polyaniline (PANI), carbon black, and cobalt precursor without any heat treatment. Characterization of new Co-PANI-C composite catalysts was done by the measurement of X-ray diffraction (XRD) and thermogravimetric analysis (TGA) for structure analysis and performed by rotating disk electrode (RDE) and rotating ring disk electrode (RRDE) for electrochemical analysis. As a result, Co-PANI-C catalyst showed 60 mV lower on-set potential for oxygen reduction reaction (ORR) than Pt/C catalyst, but the overall reduction current of Co-PANI-C catalysts by ORR was still smaller than that of Pt/C. In addition, the ORR behavior of Co-PANI-C catalysts depending on the rotation speed of electrode and the stability of Co-PANI-C catalyst under potential cycling and the performance of fuel cell conditions are also discussed.

• Conservation Science in Museum
• /
• v.1
• /
• pp.61-74
• /
• 1999

Elemental analysis of 40 glass samples from the Northern Tomb and the Southern Tomb of Hwangnam-daech'ong No. 98 was performed. Fourteen compositions of each sample were analyzed quantitatively by SEM-EDS and glass samples were classified by multivariate analysis such as PCA. All of 40 samples were confirmed to be Na₂O-CaO-SiO₂ system with about 20% of Na₂O. Samples were classified into two groups by doing PCA on concentrations of 5 major elements(SiO₂, Al₂O₃, Na₂O, CaO and K₂O). Samples included in group I showed the concentration of Al₂O₃ is about 9.7% and that of CaO, about 2.2%. In group II, concentration of Al₂O₃ is about 3.2% and that of CaO, about 4.9%. Especially yellow grains embedded in sample No. 12 were shown to be PbSnO₃ by micro XRD, which was the first coloring material ever found in Korea. Lead isotope ratios of samples No. 12 and No. 17 which contained lead were measured by TIMS. The origin of lead was traced by means of multivariate analysis such as SLDA. The result showed that lead from southern China and southern Korea had been used for making glass.

• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.633-640
• /
• 2010

This study was performed to get basic information about properties of high blaine cement for shotcrete use. Particle size distribution, setting time and compressive strength test, analysis like as SEM, DSC thermal analysis, XRD was carried out to investigate principle properties of high blaine cement. Setting time of high blaine cement was shorter and compressive strength was higher than those of ordinary portland cement (OPC). Results of analysis showed early hydration products of high blaine cement is smaller and spread widely due to increased specific surface. From the SEM observation and analysis of DSC and XRD results, it was seen that the aluminates accelerators promoted calcium aluminium hydrates while the alkali free accelerators increased ettringite and monosulfates formation. Strength and setting time measurement of cement paste with aluminate accelerator is more effective than the alkali free accelerator in reducing the setting time and increasing early strength while alkali free accelerator is more effective in increasing the strength after 7 days.

• Journal of the Korean Vacuum Society
• /
• v.17 no.5
• /
• pp.466-472
• /
• 2008

Purple Gold is the alloy consisting of 78wt%Au-22wt%Al, and is expressed as a chemical formula, $AuAl_2$. Lately it is being used for the material of accessories or the decorative ornaments, being one of the colored golds having the peculiar purple color, like White Gold and Pink Gold. Purple Gold has the weak point in shaping through casting process due to the bad malleability and castability, being the intermetalic compound of Au and Al. Therefore, it is possible to produce the final product only by the cutting and the grinding process or to use it as a decorative coat with the thin film evaporation. This study implemented two kinds of thin film experiments. One is the case that heat treatment was made after Au and Al deposition evaporated separately with a weight ratio 78:22 on the 200nm$SiO_2$/Si substrate. The other is the case that the surface deposition was made through the vacuum evaporation, keeping the glass substrate temperature remain room temperature, using the bulk $AuAl_2$ as a source. The final film property was measured, focusing on the Purple Gold's color and thickness through the bare eye inspection, the microstructure analysis, the surface resistance analysis, the color difference analysis, and XRD analysis. Purple Gold was not formed, as the excessive surface agglomeration occurred, in case of being produced and treated thermally with 12.5nmAu/40nmAl/200nm$SiO_2$/Si structure. Our results suggest that of Purple Gold films, showing the same purple color as the bulk's, were successfully deposited with the direct thermal evaporation from the $AuAl_2$ bulk source.