• 한국세라믹학회지
• /
• 제49권5호
• /
• pp.469-474
• /
• 2012

The crystallinity and phase ratio of anatase to rutile in $TiO_2$ were estimated by x-ray diffraction (XRD) and x-ray absorption spectroscopy (XAS). Traditionally, the structural characterization of $TiO_2$ powders has been carried out by XRD techniques, which are comparatively easy in use and analysis. However, materials with amorphous phase, nano-sized or nano-structured crystallinities cannot be fully characterized by XRD because XRD analysis has a limit for abnormal contributions of the nano-crystal such as the surface contribution. From the comparison with the experimental and calculated Ti K-edge XAS spectra, we found the possibility of efficient estimation in the crystalinites and the phase ratio of anatase to rutile for nano-sized $TiO_2$ mixture.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.189-190
• /
• 2018

This study produced Portland limestone cement at the rate of limestone substitution by grinding limestone and clinker together, and it conducted an XRD analysis to determine the sign language response structure as a basic study on Portland Limestone Cement. As a result of the XRD analysis, the higher the substitution rate of limestone, the more likely it is that the detection rate of ettringite is decreased. Additionally, we could see that the production volume of Mono-carbonate was increasing.

• Carbon letters
• /
• 제10권1호
• /
• pp.38-42
• /
• 2009

This study aims to find a correlation between XRD and Raman result of the oxidized high modulus carbon fibers as a function of its oxidation degrees, and compare with the isotropic carbon fiber reported early. La of the high modulus carbon fiber prepared by oxidation in carbon dioxide gas have been observed using laser Raman spectroscopy. The basic structural parameters of the fibers were evaluated by XRD as well. The La of the original high modulus carbon fibers were measured to be 144 ${\AA}$ from Raman analysis and 135 ${\AA}$ from XRD analysis. La of the 92% oxidized fiber were 168 ${\AA}$ by using Raman and 182 ${\AA}$ by using XRD. There was some correlation between the La value obtained from Raman and XRD. However the La value changes of the high modulus carbon fiber through whole oxidation process showed opposite tendency compare with the isotropic carbon fiber because of the fiber structure basically.

• Carbon letters
• /
• 제9권2호
• /
• pp.127-130
• /
• 2008

This study aims to find a correlation between XRD and Raman result of the activated carbon fibers as a function of its activation degrees. La of the isotropic carbon fiber prepared by oxidation in carbon dioxide gas have been observed using laser Raman spectroscopy. The basic structural parameters of the fibers were evaluated by XRD as well, and compared with Raman result. The La of the carbon fibers were measured to be 25.5 ${\AA}$ from Raman analysis and 23.6 ${\AA}$ from XRD analysis. La of the ACFs were 23.6 ${\AA}$ and 20.4 ${\AA}$, respectively, representing less ordered through activation process. It seems that the $I_D/I_G$ of Raman spectra were related to crystallite size(La). Raman spectroscopy has demonstrated its unique ability to detect structural changes during the activation of the fibers. There was good correlation between the La value obtained from Raman and XRD.

• 한국세라믹학회지
• /
• 제48권5호
• /
• pp.458-462
• /
• 2011

The strength of ceramic was improved by lamination by suppressing the propagation of cracks with compressive residual stress in the face layer of the laminate. Hot pressed SiAlON+SiC/SiC/SiAlON+SiC laminate discs were fabricated for tailored residual stress. The residual stress in this laminate was studied by X-ray diffraction (XRD). There was considerable compressive residual stress in the face layer. A Finite Element Analysis (FEA) was performed to support the measured XRD results and to determine the stress field in the laminate. The residual stress measured by XRD had satisfactory agreement with the analytically calculated and FEA values. The measured value by XRD was -385 ${\pm}$ 20 MPa over most of the face layer. The calculated and FEA values were -386 MPa and -371MPa, respectively. FEA also showed significantly modified stresses and the maximum tensile stress near the edge region which are possible crack generators in the presence of flaws or contact damage.

• Korean Chemical Engineering Research
• /
• 제60권4호
• /
• pp.564-573
• /
• 2022

탄산칼슘은 반응 초기 무정형의 탄산칼슘 ACC (amorphous calcium carbonate)에서 calcite, aragonite, vaterite의 세 가지 결정 형태로 변한다. 결정구조의 차이에 따라 물성이 달라지고, 이들 특성을 활용하여 다양한 분야에 응용이 가능하다. 따라서 단일 결정 구조를 가진 탄산칼슘 입자의 생성에 관한 연구가 활발히 진행되고 있다. 본 연구에서는 XRD 피크 면적을 이용한 탄산칼슘의 결정 형태별 정량분석이 이루어졌다. 순수한 vaterite와 aragonite 결정이 합성되고 이들 표준 시료의 XRD 피크 분포가 분석되었다. Calcite와 vaterite 표준 시료를 혼합 한 시료에 대한 피크 강도를 기준으로 한 경우와 피크 총면적을 기준으로 한 정량분석 값이 비교되었다. f_sV (vaterite 전체 피크 면적 기준 보정계수) 평균값은 0.654로 구해졌다. Calcite와 aragonite 표준 시료를 혼합 한 시료에 대한 피크 총면적을 기준으로 한 정량분석에서 f_sA (aragonite 전체 피크 면적 기준 보정계수) 평균값은 0.6713로 구하여졌다. 이들 보정계수를 적용하여 탄산칼슘 세 가지 결정에 대한 XRD 피크 총 면적을 기준으로 한 정량분석식 Eq. (24)~Eq. (32)이 제안되었고, 각 결정 사이의 중복 구간을 고려한 세 가지 결정에 대한 diffraction angle 구간 범위를 정하였다. 세 가지 표준 시료를 혼합한 시료에 대하여 XRD 분석을 하고 피크 면적 기준 정량분석치와 피크 높이 기준 분석치를 비교하였다.

• The Journal of Advanced Prosthodontics
• /
• 제11권5호
• /
• pp.253-261
• /
• 2019

PURPOSE. To evaluate the influence of cyclic loading on phase transformation of zirconia abutments and to compare the effectiveness of three different quantitative ageing assessment techniques. MATERIALS AND METHODS. Thirty two Y-TZP prostheses fabricated from two brands, InCoris ZI and Ceramill ZI, were cemented to titanium bases and equally divided into two subgroups (n=8): control group without any treatment and aged group with cyclic loading between 20 N and 98 N for 100,000 cycles at 4 Hz in distilled water at $37^{\circ}C$. The tetragonal-to-monoclinic phase transformation was assessed by (i) conventional x-ray diffraction (XRD), (ii) micro x-ray diffraction (${\mu}XRD$), and (iii) micro-Raman spectroscopy. The monoclinic-phase fractions (M%) were compared by two-way ANOVA. RESULTS. InCoris Zi presented significantly higher M% than Ceramill Zi in both control and aged groups (P<.001). Both materials exhibited significant phase transformation with monoclinicphase of 1 to 3% more in aged groups than controls for all three assessment techniques. The comparable M% was quantified by both ${\mu}XRD$ and XRD. The highest M% was assessed with micro-Raman. CONCLUSION. Cyclic loading produced significant phase transformation in tested Y-TZP prostheses. The micro-Raman spectroscopy could be used as an alternative to XRD and ${\mu}XRD$.

• 한국환경보건학회지
• /
• 제35권2호
• /
• pp.130-142
• /
• 2009

This study compared FTIR with XRD method for the analysis of quartz by % recovery, coefficient of variation (CV) and influence of the interference. the results were as the following. 1. In FTIR method, the coefficient of determination ($r^2$) was 0.9998 in a calibration curve of $695\;cm^{-1}$, and the limit of detection was $4.9{\mu}g/sample$. 2. The highest recovery was $799\;cm^{-1}$ (98.2%). 3. The CVpooled of the FTIR method was approximately 10% in three wave numbers. 4. The analysis of qualitative and quantitative for quartz is difficult with mixed cristobalite and iron oxide. 5. In XRD method with rotating sample holder and LynxEye detector, the coefficient of determination was 0.9996 in a calibration curve, and the limit of detection was $5.9{\mu}g/sample$. 6. The recovery and CV pooled were 104.3%, and 11 %, respectively. 7. In muffle furnace ashing, the quartz weight decreased to 34% when the maximum weight of the iron oxide was more than eight times. In conclusion, the accuracy (% recovery) and precision (CV) of FTIR and XRD method for analyzing $\alpha$-quartz were similar. FTIR method was a disadvantage for sample matrix because it indicates possibility of interference. However, XRD method distinguished specific crystalline forms of silica, and the majority of silicate minerals. In addition, XRD method recommend filter dissolution to pretreatment method.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.995-998
• /
• 2003

This paper reports the correlation between dielectric constant and degree of amorphism of the hybrid type Si-O-C thin films. Si-O-C thin films were deposited by high density plasma chemical vapor deposition using bistrimethyl- silylmethane(BTMSM, $H_{9}$C$_3$-Si-C $H_2$-Si-C$_3$ $H_{9}$) and oxygen precursors with various flow rate ratio. As-deposited film and annealed films at 40$0^{\circ}C$ were analyzed by XRD. The Si-O-C thin films were amorphous from XRD patterns. For quantitative analysis, the diffraction pattern of the samples was transformed to radial distribution function by Fourier analysis, and then compared with each other. The degree of amorphism of annealed films was higher than that of as-deposited ones. The dielectric constant varied in accordance with flow rate ratio of precursors. The lowest dielectric constant was obtained from the as-deposited film which has the highest degree of amorphism after annealing.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2002년도 추계총회 및 연구발표회 초록집
• /
• pp.130.1-130
• /
• 2002