• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.173-177
• /
• 2010

Thermal stabilizing effect of $Yb^{3+},\;Er^{3+}$ codoping into $TiO_2$ powder prepared by sol-gel method and its upconversion characteristics were analyzed. The effect of $TiO_2:Yb^{3+},\;Er^{3+}$ ions on crystallinity and phase transition was studied by X-ray diffraction (XRD). The change of band-gap energy induced from Yb and Er codoping was analyzed by UV-Vis. The band-gap energy of $TiO_2$ have been slightly narrowed by $Yb^{3+},\;Er^{3+}$ codoping, which indicated that the $Yb^{3+},\;Er^{3+}$ ions can enhance the photo-catalytic property of $TiO_2$. green and red up-conversions of $Yb^{3+}$ and $Er^{3+}$ co-doped $Y_2O_3:Yb^{3+},\;Er^{3+}$ phosphor were analyzed by PL equipped with 980 nm laser.

• Journal of Photoscience
• /
• v.9 no.2
• /
• pp.311-313
• /
• 2002

X-ray structures of pharaonis phoborhodopsin (ppR) show the different direction of the side chain of Arg72 from that of the corresponding residue (Arg82) of bacteriorhodopsin, BR. For BR, this residue is considered to play an important role in the proton pumping. In order to investigate the role of Arg72 in ppR, we constructed Arg72 mutants of R72A, R72K and R72Q, and measured the photocycle and proton pumping activities. The pH-titration curves on the absorption maximum of the mutants were shifted to alkaline in comparison of that of the wild-type. This may imply the increase of pKa of D75, suggesting the presence of the (probably electric) interaction between D75 and Arg72. Rate constants of the M-decay were 3-7 times faster than that of the wild-type, and the time for the completion of the photocycling was also reduced. Using Sn0$_2$ electrode, the rate of transmembrane proton transport was measured upon illumination. The photo-induced proton pumping activities were estimated after the corrections that are the percentages of the associated form of D75 (which has no pumping activity) and the photocycling rates. R72A and R72Q showed the reduced activity while R72K did not reduce the activity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.358-358
• /
• 2012

The application of BZO (Boron-doped Zinc Oxide) films use as the TCO(Transparent Conductive Oxide) material for display and solar cell industries, where the conductivity of the BZO films plays a critical role for improvement of cell performance. Thin BZO films are deposited on glass substrates by using RF sputter system. Then charging flow rates of O2 gas from zero to 10 sccm, thereby controlling the impurity concentration of BZO. BZO deposited on soda lime glass and RF power was 300 W, frequency was 13.56 MHz, and working pressure was $5.0{\times}10-6$ Torr. The Substrate and glass between distance 200 mm. We measured resistivity, conductivity, mobility by hall measurement system. Optical properties measured by photo voltaic device analysis system. We measured surface build according to oxygen flow rate from XPS (X-ray Photoelectron Spectroscopy) system. The profile of the energy distribution of the electrons emitted from BZO films by the Auger neutralization is measured and rescaled so that Auger self-convolution arises, revealing the detail structure of the valence band. It may be observed coefficient ${\gamma}$ of the secondary electron emission from BZO by using ${\gamma}$-FIB (Gamma-Focused Ion Beam) system. We observed the change in electrical conductivity by correlation of the valence band structure. Therefore one of the key issues in BZO films may be the valence band that detail structure dominates performance of solar cell devices. Demonstrating the secondary electron emission by the Auger neutralization of ions is useful for the determination of the characteristics of BZO films for solar cell and display developments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.433-433
• /
• 2009

ZnO-based materials have been extensively studied for optoelectronic applications due to their superiors physical properties such as wide direct bandgap (~3.37 eV), large exciton binding energy (~60 meV), high transparency in the visible region, and low cost. Especially, one-dimensional (1D) ZnO nanostructures have attracted considerable attention owing to quantum confinement effect and high crystalline quality. Additionally, various nanostructures of ZnO such as nanorods, nanowires, nanoflower, and nanotubes have stimulated the interests because of their semiconducting. and piezoelectric properties. Among them, vertically aligned ZnO nanorods can bring the improved performance in various promising photoelectric fields including piezo-nanogenerators, UV lasers, dye sensitized solar cells, and photo-catalysis. In this work, we studied the effect of the annealing temperature of homo seed layers on the formation of ZnO nanorods grown by hydrothermal method. The effect of annealing temperature of seed layer on the length and orientation of the nanorods was investigated scanning electron microscopy investigation. Transmission electron microscopy and X-ray diffraction measurement were performed to understand the effect of annealing temperatures of seed layers on the formation of nanorods. Moreover, the optical properties of the seed layers and the nanorods were studied by room temperature photoluminescence.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.13-17
• /
• 2008

Visible-light responsive $TiO_2$:Zr, N powders were prepared by polymer complex solution method and the particle properties were characterized by using transmission electron microscope, BET method, X-ray diffractometer and UV-Vis spectrophotometer. The photocatalytic reactivity of the catalysts was also estimated by analyzing NO degradation. Polyhedral $TiO_2$ powder having about 20 um in the average particle diameter was successfully prepared, The XRD analysis revealed that the as-prepared powder consisted of anatase and rutile phases. The light absorption of the as-prepared $TiO_2$:Zr, N powder was shifted to the visible light. In addition, the as-prepared $TiO_2$:Zr, N nanoparticles showed the higher photocatalytic activity than the commercial $TiO_2$ under both UV and visible lights.

• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.42-47
• /
• 2004

In this paper, we analyzed on the characteristics of the stranded wire disconnected by repeated stress. The stranded wires that were used in the experiment are PVC insulated flexible cords(VCTFK: Vinyl Insulated Vinyl Cabtyre Cord Flat-type) of $0.75mm^2,\;1.25mm^2,\;and\;2.0mm^2$. They are used to connect the load in low voltage. The stranded wires disconnected by repeated stress were magnified with optical microscope. Using X-ray, the disconnected wire were photo-graphed. we compared mechanical characteristics of the stranded wire between disconnected tendency and allowable current. On the mechanical strength of vinyl cap tire ellipse type cords under bending stress, VCTFK of $1.25mm^2$ was the strongest of them. When it was bent $826.3\pm7$ times, it appeared the disconnected tendency that element wires of VCTFK of $1.25mm^2$ are more about 1.67 times than element wires of VCTFK of $0.75mm^2$. In mechanical strength, VCTFK of $1.25mm^2$ is higher about 1.7 times than VCTFK of $0.75mm^2$. Therefore, we found out that mechanical strength was higher, when the wire had a lot of element wires. In comparison with bending stress, VCTFK of $1.25mm^2$ is the strongest among samples, and it is the most useful in wires of movable type.

• ETRI Journal
• /
• v.26 no.4
• /
• pp.315-320
• /
• 2004

This paper proposes a 10-${\mu}m$ thick oxide layer structure that can be used as a substrate for RF circuits. The structure has been fabricated using an anodic reaction and complex oxidation, which is a combined process of low-temperature thermal oxidation (500 $^{\circ}C$ for 1 hr at $H_2O/O_2$) and a rapid thermal oxidation (RTO) process (1050 ${\circ}C$, for 1 min). The electrical characteristics of the oxidized porous silicon layer (OPSL) were almost the same as those of standard thermal silicon dioxide. The leakage current density through the OPSL of 10 ${\mu}m$ was about 10 to 50 $nA/cm^2$ in the range of 0 to 50 V. The average value of the breakdown field was about 3.9 MV/cm. From the X-ray photo-electron spectroscopy (XPS) analysis, surface and internal oxide films of OPSL prepared by a complex process were confirmed to be completely oxidized. The role of the RTO process was also important for the densification of the porous silicon layer (PSL) oxidized at a lower temperature. The measured working frequency of the coplanar waveguide (CPW) type short stub on an OPSL prepared by the complex oxidation process was 27.5 GHz, and the return loss was 4.2 dB, similar to that of the CPW-type short stub on an OPSL prepared at a temperature of 1050 $^{\circ}C$ (1 hr at $H_2O/O_2$). Also, the measured working frequency of the CPW-type open stub on an OPSL prepared by the complex oxidation process was 30.5 GHz, and the return was 15 dB at midband, similar to that of the CPW-type open stub on an OPSL prepared at a temperature of $1050^{\circ}C$ (1 hr at $H_2O/O_2$).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.120-120
• /
• 2008

We demonstrate epitaxial growth of ZnO thin films on 4H-SiC(0001) substrates using pulsed laser deposition (PLD). ZnO and SiC have attracted attention for their special material properties as wide band gap semiconductors. Especially, ZnO could be applied to optoelectronic applications such as light emitting devices and photo detectors due to its direct wide bandgap (Eg) of ~3.37eV and large exciton binding energy of ~60meV. SiC shows a good lattice matching to ZnO compared with other commonly used substrates and in this regard SiC is a good candidate as a substrate for ZnO. In this work, ZnO thin films were grown on 4H-SiC(0001) substrates by PLD using an Nd:YAG laser with a 355nm wavelength. The crystalline properties of the films were evaluated by x-ray diffraction (XRD) $\theta-2\theta$, rocking curve and pole figure measurements using a high-resolution diffractometer. The surface morphology of the films was studied by atomic force microscopy (AFM).

• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.477-482
• /
• 2017

Nitrogen-doped titanium dioxide (N-doped $TiO_2$) is attracting continuously increasing attention as a material for environmental photocatalysis. The N-atoms can occupy both interstitial and substitutional positions in the solid, with some evidence of a preference for interstitial sites. In this study, N-doped $TiO_2$ is prepared by the sol-gel method using $NH_4OH$ and $NH_4Cl$ as N ion doping agents, and the physical and photocatalytic properties with changes in the synthesis temperature and amount of agent are analyzed. The photocatalytic activities of the N-doped $TiO_2$ samples are evaluated based on the decomposition of methylene blue (MB) under visible-light irradiation. The addition of 5 wt% $NH_4Cl$ produces the best physical properties. As per the UV-vis analysis results, the N-doped $TiO_2$ exhibits a higher visible-light activity than the undoped $TiO_2$. The wavelength of the N-doped $TiO_2$ shifts to the visible-light region up to 412 nm. In addition, this sample shows MB removal of approximately 81%, with the whiteness increasing to +97 when the synthesis temperature is $600^{\circ}C$. The coloration and phase structure of the N-doped $TiO_2$ are characterized in detail using UV-vis, CIE Lab color parameter measurements, and powder X-ray diffraction (XRD).

• Ecology and Resilient Infrastructure
• /
• v.3 no.4
• /
• pp.215-220
• /
• 2016

A new immobilization technique of nanoscale $TiO_2$ powder to expanded polystyrene (EPS) balls with temperature-controlled melting method was developed, and the photocatalytic activity of $TiO_2$ powder-embedded EPS balls were evaluated using methylene blue (MB) solution under ultraviolet irradiation (${\lambda}=254nm$). Based on the scanning electron microscope (SEM) images and associated energy-dispersive X-ray spectroscopy (EDX) analysis, the components of the intact EPS balls were mainly carbon and oxygen, whereas those of $TiO_2$-immobilized EPS balls were carbon, oxygen, and titanium, indicating that relatively homogenous patches of $TiO_2$ and glycerin film were coated on the surface of EPS balls. Based on the comparison of degradation efficiencies of MB between intact and $TiO_2$-immobilized EPS balls under UVC illumination, the degradation efficiencies of MB can be significantly improved using $TiO_2$-immobilized EPS balls, and surface reactions in heterogeneous photocatalysis were more dominant than photo-induced radical reactions in aqueous solutions. Thus, $TiO_2$-immobilized EPS balls were found to be an effective photocatalyst for photodegradation of organic compounds in aqueous solutions without further processes (i.e., separation, recycling, and regeneration of $TiO_2$ powder). Further study is in progress to evaluate the feasibility for usage of buoyant $TiO_2$-immobilized EPS to inhibit the excessive growth of algae in rivers and lakes.