• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.20-26
• /
• 2016

This paper presents an X-band two-stage power amplifier using GaN-HEMT. Two-stage structure was adopted to take its high gain and simple inter-stage matching network. Based on a 3D EM simulation, the bond-wire inductance and the parasitic capacitance were predicted. By reducing bond-wire inductance, Q of the matching network is decreased and the bandwidth is improved. The implemented two-stage PA shows a power gain of more than 16 dB, saturated output power of more than 42.5 dBm, and a efficiency of more than 35 % in frequency range of 8.1~8.5 GHz with an operating voltage of 40 V.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.13-18
• /
• 2001

This paper deals with finite element analysis for free vibration and forced sine vibration of Ka- and Ku- bend antenna structures using MSC/PATRAN/NASTRAN. The structures are designed to satisfy minimum resonance frequency requirement in order to decouple the dynamic interaction of the satellite with the spacecraft bus structure. From the forced sinusoidal vibration, we have observed output acceleration versus input in X-,Y- and Z- direction, based on base excitation using large mass method. The results of finite elements analysis can be used as the reference data for the experimental test of satellite antenna, resulting in the reduction of cost and time by predicting and complementing experimental data.

• Journal of electromagnetic engineering and science
• /
• v.13 no.1
• /
• pp.34-37
• /
• 2013

This paper presents a novel ultra-wideband (UWB) antenna that rejects narrow and broad bands and is suitable for wireless communications. The base of the proposed antenna has a circular patch that can cover the UWB frequency range (3.1~10.6 GHz). The interference issues caused by co-existence within the UWB operation frequency are overcome by a design that uses a parallel-coupled asymmetric dual-line with a circular monopole antenna. The proposed antenna showed a stable radiation pattern, realized gain and reflection coefficient lower than -10 dB across the UWB operation bandwidth except for 5.15~5.85 GHz and 7.25~8.4 GHz. The fabrication, simulation, and measurement results obtained for the proposed antenna were in good agreement with the expected values.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.1
• /
• pp.33-38
• /
• 1994

In this paper, waveguide banpass filters using H-plane step discontinuities are designed based on the field theory analysis and optimization of the resonator lengths as well as dimensions of discontinuities, instead of the conventional synthesis method based on the equivalent circuit. The waveguide inductive obstacles introduced by H-plane step discontinuities analyzed using mode-matching method and the generalized scattering parameters are derived. Using the derived scattering parameters of the discontinuities as well as those of resonators, waveguide bandpass filters are designed through optimization method, modified Razor search method proposed by J.H.Bandler. Using this design procedures, waveguide bandpass filters are designed and tested at X-band(center frequency 10GHz) as well as Ka-band(center frequency 35GHz).

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.417-418
• /
• 2008

A quadrature voltage controlled oscillator(QVCO) with MOS-varactors has been fabricated for X-band applications. The QVCO consists of two cross -coupled differential cores and buffer amplifiers, which has fabricated in TSMC $0.18{\mu}m$ CMOS process. The QVCO exhibits a frequency tuning range from 8.38 GHz to 10.62 GHz. The phase noise is -88 dBc/Hz at 1 MHz-offset frequency. The total bias current is 25 mA including four buffer amplifiers.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.241-245
• /
• 2009

High speed train system generates much EMI (electromagnetic interference) by arc between the pantograph and the trolley line during the running time. EMI from the tilted EMU train system which is similar to HEMU-400X system for 400 km/h speed and with the distributed engines was measured following EN50121-2, 'Railway applications. - Electromagnetic compatibility (Emission of the whole railway system to the outside world)'. Measured EMI values exceed the limiting values of EN50121-2 in high frequency band ($30\;MHz{\sim}1,000\;MHz$), but exceeding frequencies were identified that they are used for mobile communications. Measured EMI values did not exceed the limiting values in other low frequency band between 9 kHz and 30 MHz.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.6
• /
• pp.9-14
• /
• 2008

Intentional city bands and public radio frequencies could reduce the internet transmission speed on the wired lines because AM and HF band are overlapping on the xDSL up and down data steam by way of the wired transmission lines. We were designed the adaptive common mode rejection circuit with 2 way amplifier against public radio frequency. Specially our circuits were applied for power and signal lines. We could reduced the common mode rejection up to 30dB and increased the up stream speed around 1.8 times using a our developed equipments. Also it could expanded the transmission distance up to 1.7 times than old lines.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.180-184
• /
• 2002

In this paper, the electrical properties of PVD Ta and $TaN_x$ gate electrodes on $SiO_2$ and their thermal stabilities are investigated. The results show that the work functions of $TaN_x$ gate electrode are modified by the amount of N, which is controlled by the flow rate of $N_2$during reactive sputtering process. The thermal stability of Ta and $TaN_x$ with RTO-grown $SiO_2$ gate dielectrics is examined by changes in equivalent oxide thickness (EOT), flat-band voltage ($V_{FB}$), and leakage current after post-metallization anneal at high temperature in $N_2$ambient. For a Ta gate electrode, the observed decrease in EOT and leakage current is due to the formation of a Ta-incorporated high-K layer during the high temperature annealing. Less change in EOT and leakage current is observed for $TaN_x$ gate electrode. It is also shown that the frequency dispersion and hysteresis of high frequency CV curves are improved significantly by a post-metallization anneal.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.6
• /
• pp.489-496
• /
• 2021

The X-band frequencies for transmitting the data from earth observation satellites are limited, so a number of satellites share the frequency bands. In order for multiple satellites to utilize same or adjacent frequency bands, International Telecommunication Union - Radiocommunication (ITU-R) limits power flux density (PFD), which overcomes the interferences among multiple satellites. However, even under the regulation, the interference effect needs to be analyzed when multiple satellites are connected to communicate with multiple ground stations (GSs) located close to each other. In this paper, the interference effect is analyzed based on signal to interference plus noise ratio (SINR) when two low earth orbit (LEO) satellites operating in different orbits are connected to communicate with randomly located two GSs in Korean peninsula. From the analysis results, it is confirmed that there can be interferences during 365 days operation even if the satellites meet PFD requirement, but the periods under interference effects are short and the interference can be foreseen.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.7
• /
• pp.13-20
• /
• 1989

An accurate design method for rectangular microstrip patch antenna that can be applied to wide range of frequencies (C-band to X-band) is proposed. With due regard the frequency dependent effective dielectric permittivity to design formula, the inaccuracy of previous design formulae can be overcome. The results predicted by new procedure are compared well experimental results that had varying operation frequencies between 7GHz and 15GHz. Antennas are fabricated over microwave substrates with the same dielectric permittivity and thickness. Radiation power patterns are also measured and they well with theoretical values.