• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.317-328
• /
• 2017

This paper presents design and specific absorption rate analysis of a 2.4 GHz wearable patch antenna on a conventional and electromagnetic bandgap (EBG) ground planes, under normal and bent conditions. Wearable materials are used in the design of the antenna and EBG surfaces. A woven fabric (Zelt) is used as a conductive material and a 3 mm thicker Wash Cotton is used as a substrate. The dielectric constant and tangent loss of the substrate are 1.51 and 0.02 respectively. The volume of the proposed antenna is $113{\times}96.4{\times}3mm^3$. The metamaterial surface is used as a high impedance surface which shields the body from the hazards of electromagnetic radiations to reduce the Specific Absorption Rate (SAR). For on-body analysis a three layer model (containing skin, fats and muscles) of human arm is used. Antenna employing the EBG ground plane gives safe value of SAR (i.e. 1.77W/kg<2W/kg), when worn on human arm. This value is obtained using the safe limit of 2 W/kg, averaged over 10g of tissue, specified by the International Commission of Non Ionization Radiation Protection (ICNIRP). The SAR is reduced by 83.82 % as compare to the conventional antenna (8.16 W/kg>2W/kg). The efficiency of the EBG based antenna is improved from 52 to 74 %, relative to the conventional counterpart. The proposed antenna can be used in wearable electronics and smart clothing.

• 한국환경복원기술학회지
• /
• 제18권6호
• /
• pp.51-60
• /
• 2015

This study conducted shear strength test and plate bearing test to look into the characteristics of bearing capacity using geosynthetics case on forest road surface. The shear strength test showed that the internal friction angle at the time when geosynthetics was used was measured larger on average than that in the unreinforced case. Therefore, using geosynthetics case produced more bearing capacity reinforcement effect. The result from the comparison test of internal friction angle by geosynthetics type revealed that the internal friction angle at the time when geotextile case was used was measured larger. That was attributable to the difference between the area of the total cross section of geotextile made in type of non-woven fabric and its material. Plate bearing test showed that the settlement at the time when geosynthetics was used was measured smaller than that in the unreinforced case. Therefore, using geosynthetics produced more bearing power reinforcement effect. The result from the comparison test showed that geogrid case was measured smaller than geotextile case. Henceforth, It is seemed that it will be necessary to keep studying the reinforcement engineering and process of forest road surface which fits the characteristics and conditions of geosynthetics to prevent forest road demage.

• 건축역사연구
• /
• 제14권2호
• /
• pp.143-157
• /
• 2005

This study aims to analyze functions and characteristics of 'Cha-il(遮日)' which was used at ritual events(宮中儀禮行事) in the Joseon dynasty, Joseon dynasty had many ritual events related with O-Rae(五禮). Cha-il was almost used at important ritual events, especially at the congratulatory events. The congratulatory events(宮中宴享) are the representative events were held with many temporary install facilities(假設施設) in a palace. Cha-il was a kind of Korean traditional membrane structures. Cha-il was set up for cutting off interior space from sunlight and rain. In general, Cha-il was Consisted of Cha-il-jang(遮日帳:woven fabric), Cha-il-jook(遮日竹:bamboo column), some ropes, and fixing wares. In the congratulatory events, three types of Cha-il. were set up. Baek-mok-Dae-Cha-il(白木大遮日)was made of cotton cloth. Yu-Dun-Cha-Il(油芚遮日) was made of oiled paper or oiled cotton cloth. Man-Joen-Cha-Il(滿箭遮日) consisted of wooden structure. Baek-mok-Dae-Cha-il(白木大遮日)was set up on the most important area of stage for protecting from sunlight. Yu-Dun-Cha-Il was set up on less important area of stage for protecting from sunlight and rain. Man-Joen-Cha-Il was set up below Baek-mok-Dae-Cha-il for supporting and draining raindrops off. The results of this study were as follows; Functions of Cha-il were to protect ritually space from sunlight and rain, and to extend ritually space, and to reconstruct ritually space. Cha-il was the peculiar temporary install facility which differed from other countries.

• 한국생산제조학회지
• /
• 제23권3호
• /
• pp.250-258
• /
• 2014

Due to recent industrial growth and development, there has been a high demand for light and highly durable materials. Therefore, a variety of new materials has been developed. These new materials include carbon fiber reinforced plastic (CFRP or CRP), which is a wear-, fatigue-, heat-, and corrosion-resistant material. Because of its advantageous properties, CFRP is widely used in diverse fields including sporting goods, electronic parts, and medical supplies, as well as aerospace, automobile, and ship materials. However, this new material has several problems, such as delamination around the inlet and outlet holes at drilling, fiber separation, and tearing on the drilled surface. Moreover, drill chips having a fine particulate shape are harmful to the work environment and engineers' health. In fact, they deeply penetrate into machine tools, causing the reduction of lifespan and performance degradation. In this study, CFRP woven and unidirectional prepregs were formed at $45^{\circ}$ and $90^{\circ}$, respectively, in terms of orientation angle. Using a high-speed steel drill and a TiAIN-coated drill, the two materials were tested in three categories: cutting force with respect to RPM and feed speed; shape changes around the input and outlet holes; and the shape of drill chips.

• 디자인학연구
• /
• 제13권4호
• /
• pp.213-223
• /
• 2000

현대산업의 주 구성요소인 컴퓨터 자동화는 섬유디자인 분야에 커다란 변화를 가져왔다. 패턴을 디자인할 때 수작업에만 의존해 왔던 디자이너들은 디자인과 색채의 다양성과 제작시간의 단축하기 위해 CAD를 디자인 도구로 하여 패턴을 창조하고 그것을 구매자에게 프리젠테이션하는 등 컴퓨터 활용이 보편화되고 있다. 당초무늬는 어느 특정식물을 소재로 패턴화 시킨 것이 아니라 이집트에서 발견된 인동문을 모체로 하여 발전된 공상적인 식물덩굴무늬로서 세계적인 무늬이다. 당초무늬는 줄기를 기준으로 꽃이나 잎이 서로 얽히어 연결됨으로서 아름답고 유연한 선을 나타내고 있으며 이 같은 선은 단순하면서도 장식적인 요소가 잘 표현되어 있다. 한국에서 당초문양은 장수와 다남을 상징하는 상서로운 문양이기 때문에 예로부터 우리 조상들이 즐겨 사용했으며 생활 속에 깊숙이 자리잡고 있다. 본 연구는 당초문양을 패턴의 모티브로 하여 CAD를 이용하여 패턴 디자인함으로써 디자인 개발의 다양성을 제시하였다.

• Composites Research
• /
• 제18권6호
• /
• pp.19-25
• /
• 2005

본 논문에서는 하이브리드 복합재 틸팅차량 차체에 대한 시험적 연구를 수행하였다. 시험에 적용된 하이브리드 복합재 틸팅차량 차체는 길이가 23m이며 40mm두께의 알루미늄 하니콤 코어와 2mm의 직조된 탄소/에폭시 면재로 구성된 샌드위치 구조물이다. 하이브리드 복합재 틸팅차량 차체의 구조적 거동과 안전성을 규명하기 위해 수직하중- 차단압축하중, 비틀림하중 및 3점지지 하중조건하에서 정적인 하중시험을 수행하였다. 시험은 JIS E 7105규격에 근거하여 수행되었다. 시험을 통해 수직하중하에서 최대처짐은 최대 12.3mm이며 굽힘강성은 $0.81\times10^{14}\;kgf{\cdot}mm^2$로 도시철도차량성능기준을 만족하고 있었다. 또한 강도 측면에서도 탄소/에폭시 면재의 파단변형률의 $20\%$ 이내로 안전도를 만족하였다.

• 한국의류산업학회지
• /
• 제15권4호
• /
• pp.620-629
• /
• 2013

This study examines the rustling sound characteristics of electrospun nanofiber web laminates according to layer structures. This study assesses mechanical properties and frictional sounds (such as SPL); in addition, Zwicker's psychoacoustic parameters (such as Loudness (Z), Sharpness (Z), Roughness (Z), and Fluctuation strength (Z)) were calculated using the Sound Quality Program (ver.3.2, B&K, Denmark). The result determined how to control these characteristics and minimize rustling sounds. A total of 3 specimens' frictional sound (generated at 0.63 m/s) was recorded using a Simulator for Frictional Sound of Fabrics (Korea Patent No. 10-2008-0105524) and SPLs were analyzed with a Fast Fourier Transformation (FFT). The mechanical properties of fabrics were measured with a KES-FB system. The SPL value of the sound spectrum showed 6.84~58.47dB at 0~17,500Hz. The SPL value was 61.2dB for the 2-layer PU nanofiber web laminates layered on densely woven PET(C1) and was the highest at 65.1dB for the 3-layer PU nanofiber web laminates (C3). Based on SPSS 18.0, it was shown that there is a correlation between mechanical properties and psychoacoustic characteristics. Tensile properties (LT), weight (T), and bending properties (2HB) showed a high correlation with psychoacoustic characteristics. Tensile linearity (LT) with Loudness (Z) showed a negative correlation coefficient; however, weight (T) with Sharpness (Z) and Roughness (Z), and bending hysteresis (2HB) with Roughness (Z) indicated positive correlation coefficients, respectively.

• 한국도로학회논문집
• /
• 제7권4호
• /
• pp.9-20
• /
• 2005

본 연구는 아스팔트 덧씌우기 포장에 나타나는 반사균열을 제어하기 위하여 노후된 시멘트 콘크리트 포장과 아스팔트 덧씌우기 포장 경계면에 보강재의 효과적인 부착 방법을 찾기 위하여 수행하였다. 이를 위한 부착재로는 RSC-4 유화아스팔트, 컴파운드, 불포화 폴리에스터 수지 (UPR) 등 3종류를 사용하였다. 또한 아스팔트 혼합물은 3종류의 밀입도 혼합물(AC 60-80, RLDPE 8%, PG 76-22)을 사용하였다. 보강 재료로서 유리섬유 그리드 하부에 직포가 부착된 것을 사용하였다. 복합모드 파괴(mode II)의 모사를 위한 촉진시험은 휠트랙킹 장비를 이용하여 수행하였다. 반사균열의 진전은 피로수명으로서 하중 사이클 수에 따라 측정하였고, 공시체의 변위는 각각 시험 공시체에 대하여 demec 게이지를 이용하여 측정하였다. 본 연구 결과, UPR 부착이 가장 효과적이었으며 다음은 RSC-4의 순이었다. 그러나 현장 적용성을 고려할 때 , RSC-4 유제가 보강 재료의 부착을 위해 적절한 선택으로 판단된다.

• 통상정보연구
• /
• 제11권1호
• /
• pp.95-116
• /
• 2009

Korea-Us FTA negotiation started in February 2006 with a view to overcoming those uncertainties in the global market and was finally concluded in April, 2007. The Agreement was officially signed between ministers two month later and it is expected to be ratified this year even though the process is most likely to be painful in both countries by the political resistances. For the new President of the United States, effective leadership will depends largely on how to encourage domestic industries such as Automobile industry and Iron and Steel industry from the financial crisis. Many trading partners of US worry about US foreign trade policy changes to protectionism that might be unequal to bear. Korea textile industry is one of the major industry in Korea as it occupies 15% of total number of manufacturers, 11% of total employment and 5% of national GDP. Korea-US FTA will provide a breakthrough for bouncing back by exploring new market. US agreed to remove all tariff and non-tariff barriers to 87% of textile items under trading. This study shows that Korean textile industry has been losing it's competitiveness as textile quota system abolished in the year 2005 and has been traced by pursuers such as China, India and Vietnam. In case of woven fabric which was a representing export item of Korea lost price competitiveness against China after 2005. This study seeks the strategy of Korea textile industry in the US market by utilizing the capacity of KOTRA offices in US. All possible statistical data obtained in the US were used for analysing the competitiveness. Fabrics and Garments are analysed independently with a view to finding out real trends of textile market in US. This study also suggest Korea's textile industry strategic ideas obtained from the potential buyers to show the way to penetrate into US market.

• 한국입자에어로졸학회지
• /
• 제12권3호
• /
• pp.51-56
• /
• 2016

Due to recent development in nanotechnology and increasing usage and production of nanomaterials, numerous studies related to environment, sanitation and safety handling of nanoparticle are being conducted. Since nanoparticles can be easily absorbed into human bodies through breathing process, based on their toxic substances and their large specific surface, these particles can cause serious health damage. Therefore, to reduce nanoparticle emissions, nanofiltration technology is becoming a serious issue. Filtration is a separation process during which a fluid passes through a barrier by removing the particles from the stream. Barrier filters can be made of various materials and shapes. One of the most common type of barrier filter is the fibrous filter. Fibrous filters are divided in two types: nonwoven and woven fabrics. Polypropylene is a thermoplastic material, used as a base material for melt blown nonwoven fabric. In this study, we examined filtration property of KCl nanoparticles with a mean particle diameter of 75 nm using multilayer meltblown filter samples. These experiments verify that the penetration of nanoparticle in the filter correlate with pressure drop; the meltblown layer MB1 has the greatest effect on dust collection efficiency of the filter. Among all tested samples, dust collection efficiency of 2-layer filter was best. However, when considering the overall pressure drop and dust collection efficiency, the 4-layer filter has the highest quality factor for particles smaller than 70 nm.