• 한국분무공학회지
• /
• 제26권4호
• /
• pp.189-196
• /
• 2021

Spray drift of agricultural nozzles has become a big issue because it causes low precision targeting and environmental pollution. In order to reduce the spray drift, study spray characteristics of agricultural nozzles is virtually important. In this study, shadowgraph and Mie-scattering visualization techniques were used to study the macroscopic spray and atomization characteristics of an agricultural nozzle. PDPA was used to measure the atomization characteristics of spray. The injection pressure is set to 1 bar, 3 bar and 5 bar, which covers the working range of the nozzle. For the PDPA experiment, 75 points were measured in an area of 160 mm × 120 mm at 10 mm intervals directly below the nozzle to grasp the overall atomization characteristics of the spray. It was found that the spray width and sheet width showed a linear correlation. As the injection pressure increased, the sheet expansion in the 0-degree direction and the sheet swing in the 90-degree direction jointly promoted the breakup of the sheet. In addition, the area close to the central axis had a large droplet velocity, and since a large droplet velocity promoted atomization of spray, the area close to the central axis had a smaller spray droplet diameter than the left and right regions.

• 한국지반공학회논문집
• /
• 제25권11호
• /
• pp.39-51
• /
• 2009

본 연구는 지반변형을 일으키는 경사모래지반에 매설된 사각형 수동열말뚝의 모형실험에 대한 것이다. 실험은 지반의 경사각을 조절하여 지반파괴를 유도 하였고, 말뚝의 형상, 위치, 간격을 달리하여 말뚝 거동을 측정하였다. 그 결과 수동말뚝에 작용하는 토압과 수평저항력 그리고 지반변형억제 효과를 확인하였다. 전면 폭이 넓은 B-type 말뚝이 측면 폭이 넓은 H-type 말뚝보다 지반변형억제 효과가 크게 나타났다. 사면경사에 따른 수평저항력 그래프를 이용하여 사면의 파괴각, 말뚝과 지반의 분담력을 알 수 있다.

• 한국정밀공학회지
• /
• 제25권9호
• /
• pp.109-115
• /
• 2008

The cleaning process of contaminant particles adhering to the microchips, integrated circuits (ICs) or the like is essential in modern microelectronics industry. In the cleaning process particularly working with the application of inert gases, the removal of contaminant particles of submicron scale is very difficult because the particles are prone to reside inside the boundary layer of the working fluid, The use of cryogenic $CO_2$ cleaning method is increasing rapidly as an alternative to solve this problem. In contrast to the merits of high efficiency of this process in the removal of minute particles compared to the others, even fundamental parametric studies for the optimal process design in this cleaning process are hardly done up to date, In this study, we attempted to measure the cleaning efficiency with the variations of some principal parameters such as mass flow rate, injection distance and angle, and tried to draw out optimal cleaning conditions by measuring and evaluating an effective cleaning width called $d_{50}$.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권1호
• /
• pp.72-77
• /
• 2013

RF 마그네트론 스퍼터링법의 스퍼터링 조건에 따른 TFT 구동회로를 위한 ZnO 박막의 구조적 특성에 관해 연구하였다. ZnO 박막은 RF 파워 및 증착압력을 변화시킴으로서 성장시켰다. 구조적 특성은 X-선 회절 분석기(XRD)와 원자력간 현미경(AFM)에 의해 분석되었다. ZnO 박막은 100W의 RF 파워에서 충분한 결정도를 가졌다. 그러나 RF 파워가 증가함에 따라 ZnO 박막의 표면 거칠기가 증가하였고 증착압력이 5mTorr에서 15mTorr로 증가함에 따라 ZnO(002) 피크의 반치폭(FWHM)이 증가하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2597-2600
• /
• 1999

Semiconductor devices can be series stacked for the application of high voltage switching. It can provide high reliability and long lifetime by the safe design with a reasonable margin. The equal voltage distribution at solid-state switches in series should be guaranteed. Static and dynamic voltage division, over current protection must be considered carefully in the design stage. A fast switching thyristor is a good candidate for the high power pulse applications. A high voltage switching module is designed and tested. Its specifications are working voltage of 70 kV, switching pulse width of 120${\mu}s$, peak switching current of 220A, maximum repetition rate of 200pps. The module can be series connected to get higher working voltage. This paper presents the design details and the test results are compared with expected circuit simulations.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.321-324
• /
• 2002

Hydraulic valve control the pressure and the How of fluid by the hydraulic oil transfered from pump but the ER fluid consists of solid particles of micrometer in size and insulating oil so in the general hydraulic valve. We invented ER-Valve using ER fluid as working fluid. The ER fluid, working fluid of ER-Valve is a functional fluid to represent the feature of fluid according to strength of electric field. In this research we made our own 4 types of plate type ER-Valve which has same surface but different width and length and then we conducted performance test. We measured flow rate and pressure drop of fluid which is flowing in the ER-Valve according to the electric field strength to conduct this test. We modeling ER-Valve relating to ER-Valve system and yield shear stress according to the strength of electric field. We used the pressure drop according to the strength of electric field by differential pressure gauge in the our own made ER-Valve. This test reviewed experimental the special changes of ER-Fluid in the steady flow condition.

• Journal of Biosystems Engineering
• /
• 제29권6호
• /
• pp.487-494
• /
• 2004

This study was conducted to develope a fertilizer-soil incorporation band tiller for the walking cultivator. Because the mixing of soil and fertilizer in the furrow of dry-field has been done manually, several time, heavy labor and much man power were required for the job. This rotary type implement is developed to substitute this manual operation for soil-fertilizer incorporation. The results of this study are summarized as follows : 1) This implement was composed of tilling device, fertilizer application device, frame and tail wheel device. 2) The revolution of driving wheel was $11\~28\;rpm$, that of application roller was $13\~14\;rpm$ the application rate range per revolution of driving wheel was $4.43\~11.80\;g$g and the application rate range by the working speed and the opening quantity was $84.12\~557.20\;g/min$. 3) The adequate working speed was $0.20\~0.40\;m/s$ and the required minimum width of open furrow was 250 mm.

• 한국화재소방학회논문지
• /
• 제24권1호
• /
• pp.111-115
• /
• 2010

본 논문은 단독형 화재감지기에 무선통신기능을 융합한 화재감지장치를 개발하고자 ZigBee 통신기술을 단독형화재감지기의 신호처리방식으로 채택하여 무선 네트워크와 결합이 가능하도록 설계하였다. 화재감지시 출력전압은 0.4V, 동작 펄스폭은 $600{\mu}s$로 실험하였다. LED감시등은 30초 주기로 동작하고 0.12mA, 동작시에는 0.5초 주기로 하며 사용전류가 7mA가 흐르도록 하여 전원회로, Chamber테스트, 연기테스트, IRED, LED 점등등 각 부분이 일정 시간 내에 정상적으로 동작되어 그 적정성을 확인하였다.

• Journal of Electrical Engineering and Technology
• /
• 제10권5호
• /
• pp.2018-2030
• /
• 2015

A two stage ac drive configuration consisting of a single-phase line commutated rectifier and a three-phase voltage source inverter (VSI) is very common in low and medium power applications. The deterministic pulse width modulation (PWM) methods like sinusoidal PWM (SPWM) could not be considered as an ideal choice for modern drives since they result mechanical vibration and acoustic noise, and limit the application scope. This is due to the incapability of the deterministic PWM strategies in sprawling the harmonic power. The random PWM (RPWM) approaches could solve this issue by creating continuous harmonic profile instead of discrete clusters of dominant harmonics. Insufficient filtering at dc link results in the amplitude distortion of the input dc voltage to the VSI and has the most significant impact on the spectral errors (difference between theoretical and practical spectra). It is obvious that the sprawling effect of RPWM undoubtedly influenced by input fluctuation and the discrete harmonic clusters may reappear. The influence of dc link fluctuation on harmonics and their spreading effect in the VSI remains invalidated. A case study is done with four different filter capacitor values in this paper and results are compared with the constant dc input operation. This paper also proposes an ingenious RPWM, a ripple dosed sinusoidal reference-random carrier PWM (RDSRRCPWM), which has the innate capacity of suppressing the effect of input fluctuation in the output than the other modern PWM methods. MATLAB based simulation study reveals the fundamental component, total harmonic distortion (THD) and harmonic spread factor (HSF) for various modulation indices. The non-ideal dc link is managed well with the developed RDSRRCPWM applied to the VSI and tested in a proto type VSI using the field programmable gate array (FPGA).

• Geomechanics and Engineering
• /
• 제22권4호
• /
• pp.319-328
• /
• 2020

This paper investigates the effect of the width of failure and tension crack (TC) on the stability of cohesive-frictional soil slopes in three dimensions. Working analytically, the slip surface and the tension crack are considered to have spheroid and cylindrical shape respectively, although the case of tension crack having planar, vertical surface is also discussed; the latter was found to return higher safety factor values. Because at the initiation of a purely rotational slide along a spheroid surface no shear forces develop inside the failure mass, the rigid body concept is conveniently used; in this respect, the validity of the rigid body concept is discussed, whilst it is supported by comparison examples. Stability tables are given for fully drained and fully saturated slopes without TC, with non-filled TC as well as with fully-filled TC. Among the main findings is that, the width of failure corresponding to the minimum safety factor value is not always infinite, but it is affected by the triggering factor for failure (e.g., water acting as pore pressures and/or as hydrostatic force in the TC). More specifically, it was found that, when a slope is near its limit equilibrium and under the influence of a triggering factor, the minimum safety factor value corresponds to a near spherical failure mechanism, even if the triggering factor (e.g., pore-water pressures) acts uniformly along the third dimension. Moreover, it was found that, the effect of tension crack is much greater when the stability of slopes is studied in three dimensions; indeed, safety factor values comparable to the 2D case are obtained.