• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.04a
• /
• pp.167-173
• /
• 2006

Deinking is a series of unit operations designed to detach ink from cellulose fibers and separate the dispersed ink from the pulp slurry. Deinking chemicals are process aids that enable expensive mill equipment used in these unit operations to operate more efficiently - often much more efficiently. We propose the blended deinking agent with cellulolutic enzymes and synthetic collector in deinking pulp of conventional alkaline method. The deinking efficiency of old news print in alkaline pH was enhanced with enzyme treatments. The brightness of deinked pulp was increased with less residual ink particles and yield of enzymatic deinked pulp was improved compared to the deinked pulp of conventional alkaline method. Enzymes in biomass were use to Chemical Deinking for reduce environment pollution through surfactant and improve surfactants. examining into compatibility Enzymes and surfactants, these new materials are studied efficiency of deinking efficiency.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.2
• /
• pp.61-66
• /
• 2010

Corn stalk, one of the most abundant agricultural residue in the world, was examined in this study to use it as an alternative fiber source of wood fiber. In order to find the proper way to utilize corn stalk more efficiently, the morphological properties and the papermaking properties of the, bast fibers and the corn pith, were evaluated respectively. Although the bast fiber fraction showed comparable properties to those for hardwoods in the fiber properties and the papermaking properties, the pith resulted in low brightness and low drainage rate. But the short and flexible fibers in pith fraction led to dense and compact handsheet structure, correspondingly the higher sheet strength. There big differences in properties between bast fiber and pith should be considered for the fully utilization of corn stalk.

• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.35-41
• /
• 2014

The wood pellet, which is one of the woody biomass energy, has very high economic efficiency and combustion efficiency during their combustion. The existing pellet burner have many problems such as low combustion efficiency, flame stabilization, ash problem and ignition time etc. We developed cyclonic wood pellet burner aim to 20,000kcal/hr boiler and measured temperature profiles and exhaust gases in order to investigate the flame stability and optimum combustion condition at any air flow conditions. As results, we confirmed the reappearance and the isotropy of the experimental results in the burner. At the first air flow inlet condition of excess air ratio ${\alpha}=0.02$, second air flow $490{\ell}/min$ had the best combustion condition when pellet supplied 30g. This result means that we need much air supply only for the swirling of second air flow. So we tested various second air flux at first air excess air ratio ${\alpha}=0.7$ condition. At this condition, we could find out that we don't need much second air and total air flux compared to the former condition. We will continuously test this work of air flow distribution, and swirl effect of first air flow, and ash elimination.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.3
• /
• pp.11-17
• /
• 2015

In acid hydrolysis process of biomass saccharification. neutralization of acid hydrolyzate is essential step, which resulted in dissolved cations in glucose solution. Impact of cations to Kluyveromyces marxianus in glucose solution was investigated focused on ethanol fermentation. Either potassium or sodium cations decreased the ethanol fermentation and glucose to ethanol conversion. Glucose consumption by K. marxianus was delayed by increasing potassium cation concentration as completely consumed within 12 h in potassium cation 0.46 mol and 0.92 mol but within 24 h in potassium cation 1.38 mol. Also, ethanol fermentation process was slowed down with increasing concentration of the potassium sulfate. Fermentation of glucose solution to ethanol was more inhibited by sodium cation than potassium cation in glucose solution. Glucose was completely consumed within 24 h in sodium cation 0.95 mol. but at 1.90 mol or 2.84 mol in sodium cation could not finish the fermentation within 48 hour. Ethanol concentration was 22.26 g/L at low sodium cation in glucose solution with complete fermentation within 24 h. With increasing sodium cation in glucose solution, final ethanol concentration was reached at 14.10 g/L (sodium cation con) and 0.21 g/L (sodium cation con), which meant delaying of fermentation by sodium cations.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.4
• /
• pp.80-84
• /
• 1991

Lignocellulosic biomass including acetosolv ricestraw and spruce lignin were liquefied and converted into liquid hydrocarbons by catalytic hydroliquefaction reaction. These experimental works were carried out in 1-liter-capacity autoclave using 50% tetralin and m-cresol solution respectively as soluble solvent and Ni. Pd. Fe and red mud as catalyst. $H_2$ gas was supplied into the reactor for escaltion of deoxhydroenolysis reaction. Catalyst concentrations were 1 % of raw material based on weight. The ratio between raw materials and soluble solvent are 1g and 10cc. The reaction conditions are 400-$700^{\circ}C$ of reaction temperature, 10-50 atms of reaction pressure. The highest yield of hydrocarbon, so called "product oil" showed 32% and 5.5% of lowest char formation when red mud was used as catalyst. The product oil yields from those of other catalysts were in the range of 20-29%. The influence of different initial hydrogen pressures was examined in the range d 30-50 atms. A minimum pressure of 35 atms was necessary to obtain a complete recovery of souble solvent for recycling.

• Advances in Energy Research
• /
• v.4 no.3
• /
• pp.223-237
• /
• 2016

The excess use of conventional sources of energy by the industries and power sector result in acute shortage of energy produced by fossil fuel. To overcome this energy crisis, biomass feedstock is used to produce syngas or producer gas. For cleaning the dust particle present in the producer gas cyclone separators are largely used. In this paper we investigate the performance parameters of cyclone separator mainly efficiency and pressure drop for different feedstock. Cyclone performance has been evaluated based on experimentation and empirical approach using Leith and Licht model. The same has also been calculated by using turbulent RSM in Ansys Fluent for Wood and Coconut shell feedstock. Experimental results show that using feed stock with 10 % Calcium oxide (CaO) by weight, the efficiency of cyclone got reduced from 71.87% to 70.75% for wood feed stock, whereas in case of coconut shell, the cyclone efficiency got reduced from 78% to 73.44%. It is also seen that Leith and Licht model and Reynolds stress model (RMS) predicts very close to the particle collection efficiency evaluated by using experimental data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.116-125
• /
• 2014

Pyrolysis oil (PO), derived from biomass through fast pyrolysis process have the potential to displace significant amounts of petroleum fuels. The PO derived from wood has been regarded as an alternative fuel to be used in diesel engines. However, the use of PO in a diesel engine is very limited due to its poor properties like low energy density, low cetane number, high acidity and high viscosity of PO. Therefore, one of the easiest way to adopt PO to diesel engine without modifications is blended with other fuels that have high centane number. However, PO that has high amount of polar chemicals is immiscible with non polar hydrocarbons of diesel or biodiesel. Thus, to stabilize a homogeneous phase of diesel/biodiesel-PO blends, a proper surfactant should be used. Nevertheless, PO which was produced from different biomass type have varied characteristics and this complicates the selection of a suitable additive for a specific PO-diesel emulsion. In this regard, a more simple approach such as the use of a co-solvent like ethanol or butanol to induce a more stable phase of the PO-diesel mixture could be a promising alternative. In this study, a diesel engine operated with diesel/biodiesel-PO-butanol blends was experimentally investigated. Performance and gaseous & particle emission characteristics of a diesel engine were examined under the engine loads of IMEP 0.2 ~ 0.8MPa.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.16 no.1
• /
• pp.79-88
• /
• 2008

The production of bioethanol, which is one of the alternative fuel, cause the various problem such as agflation in human society. As a substitute for the feedstock, lignocellulosic biomass have a big potential. However, bioethanol production with cellulosic material is not commercialized due to high cost. Thermochemical pretreatment to improve the rate of enzyme hydrolysis and increase the recovery of fermentable sugar, is required in order to achieve the cost down in bioethanol production. In this study, various problems and technologies for pretreatment is introduced. Acid hydrolysis, alkali hydrolysis, steam explosion, organosolv process, ammonia explosion, and wet oxidation pretreatment remove lignin and hemicellulose, and reduce cellulose crystallinity. Optimization of pretreatment process on various sources of lignocellulosic biomass such as softwood, hardwood, and straw should be performed.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.381-389
• /
• 2015

In this study, the effects of moisture content and particles size of ground particles of torrefied larch chips on the pelletizing process were investigated depending on torrefaction conditions ($220^{\circ}C$-50 min, $250^{\circ}C$-50 min, $250^{\circ}C$-120 min). The moisture content in the torrefied chip decreased to 0.69~1.75%, while ash content and calorific value increased compared to untreated chip. In addition, weight loss significantly increased during torrefaction due to hemicellulose degradation. The carbon content in torrefied larch chip increased compare to untreated larch chip, while the hydrogen and oxygen contents decreased. The lignin and glucan contents in torrefied larch chip increased with increasing severity of the torrefaction condition, while hemicellulose decreased. In the particle size distribution of ground particles of torrefied larch chip, larch torrefied at severe conditions was found to produce smaller particles (~1 mm) than that of the larch torrefied at mild conditions. Macropore (over $500{\AA}$) in the torrefied particle was produced during torrefaction. During the pelletizing using ground particles of torrefied larch chip, the pressure needed in pelletizing decreased and pellet length increased with increasing moisture content, regardless of the particle size.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.6
• /
• pp.1678-1686
• /
• 2020

This study attempted to derive the possibility of using wood pellet using rice husk, which is an agricultural byproduct, and tried to improve the lower calorific value of rice hulls thorough expansion technology and combustion additives. In the physical and chemical analysis of rice husk, the result was obtained that the chlorine content was 0.09%, which did not meet the wood pellet quality standard of Korea. When making rice hulls into expanded rice husk through the expansion technology, the chlorine content decreased, resulting in a product of 0.02%, which is equivalent to the wood pellet standard of Korea, and the calorific value was also increased to 4,280 kcal/kg compared to the existing 3,780 kcal/kg. To obtain a product of 5,000 kcal/kg or more, borax, hydrogen peroxide, and sodium hydroxide was used as combustion improver. However the improvement in calorific value was insufficient. After conversion to coffee oil path using coffee grounds, which is a waste resource biomass, it is mixed into an expanded rice husk, and when the product is analyzed, the coffee oil 15 wt% mixed product shows an excess of 4,949 kcal/kg. When using rice husk, an agricultural byproduct, as wood pellets, it is considered desirable to use waste resources to improve the calorific value, and according to the results of this study, when mixing coffee oil, rice husk can be sufficiently used as wooden pellets.