• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.353-362
• /
• 2000

Herringbone groove journal bearing (HGJB) is developed to improve the static and dynamic performances of hydrodynamic journal bearing. In this study, static and dynamic compressible isothermal lubrication problems are analyzed by the finite element method together with the Newton-Raphson iterative procedure. This analysis is introduced for prediction of the static and dynamic characteristics of air lubricated HGJB for various bearing configurations. The bearing load characteristics and dynamic characteristics are dependent on geometric parameters such as asymmetric ratio, groove depth ratio, groove width ratio and groove angle.

• Structural Engineering and Mechanics
• /
• 제3권3호
• /
• pp.229-244
• /
• 1995

The parametric instability behaviour of a plate subjected to localized in-plane compressive or tensile periodic edge loading is studied, considering the effects of damping into the system. Different edge loading cases have been considered. Damping has been introduced in the form of proportional damping. Dynamic instability behaviour under compressive or tensile periodic edge loading shows that the instability regions are influenced by the load band width and its location on the edge. The effects of damping on the instability regions show that there is a critical value of dynamic load factor beyond which the plate becomes dynamically unstable. The critical dynamic load factor increases as damping increases. Damping generally reduces the widths of the instability regions.

• Journal of Power Electronics
• /
• 제19권5호
• /
• pp.1153-1161
• /
• 2019

A current sharing controller is proposed in this paper for parallel-connected converters. The proposed controller is based on the calculation of the magnitudes of system current space vectors. Good current distribution between parallel converters is achieved with only one Proportional-Integral (PI) compensator. The proposed controller is analyzed and the circulating current impedance is derived for paralleled systems. The performance of the new control strategy is experimentally verified using two parallel connected converters employing Space Vector Pulse Width Modulation (SVPWM) feeding a passive RL load and a 2.2 kW three-phase induction motor load. The obtained test results show a reduction in the current imbalance ratio between the converters in the experimental setup from 53.9% to only 0.2% with the induction motor load.

• 한국강구조학회 논문집
• /
• 제25권4호
• /
• pp.347-357
• /
• 2013

최근, 콘크리트 충전강관 기둥(CFT)은 우수한 구조성능을 인정받아 현장적용이 활발하게 이뤄지고 있다. 한편 강재개발과 가격 상승으로 인해 단면을 효율적으로 사용하고자 하는 연구가 지속적으로 진행되고 있다. 본 연구실에서는 단면의 효율을 극대화 하기 위해 얇은 L형 플레이트 4개를 각형강관으로 형성한 단면을 제안한다. 이로 인해 강관 내부에 형성된 리브는 폭 중앙에 위치하고 있어 콘크리트와의 앵커역할이 가능하다. 또한 동일한 단면적을 갖는 일반 CFT기둥에 비해 우수한 좌굴내력과 변형성능이 발휘됨을 실험으로 평가되었다. 본 연구에서는 활용범위를 넓히고자 얇은 강판으로 조립된 신형상 기둥을 제안하며 구조적 성능을 재평가 하고자 한다. 실험 주요변수 폭두께비(b/t: 78,96,107) 이다. 실험결과 규준에서 제시하고 있는 폭두께비를 초과했음에도 내부에 설치된 리브의 앵커역할로 인해 충분한 내력을 발휘하며, 변형성능 향상에 유리한 것으로 분석되었다.

• 한국지반공학회논문집
• /
• 제27권2호
• /
• pp.5-15
• /
• 2011

일본에서 개발된 원추형 팽이기초(Top-Base Foundation)와 국내에서 개발된 부양형 팽이기초(Floating Top-Base Foundation)를 대상으로 대표 점토질 연약지반인 저압축성점토, 점토질 실트, 점토질 모래에 타설하여 실내모형실험을 수행하였다. 본 실험을 통해 하중-침하량, 기초측면 히빙량, 지중응력분포 등을 측정하여 두 가지 팽이기초의 성능을 비교 평가하였다. 또한, 단변길이 증가에 따른 침하량 변화를 분석하였다. 실내모형실험 결과 부양형 팽이기초가 지지력 증진, 침하량 저감, 응력분산효과, 측방구속력에 대해서 좀 더 우수한 성능을 발휘하는 것으로 나타났으며, 기초폭증가에 따른 침하량은 팽이기초 $5{\times}5$배열을 기점으로 수렴하였다.

• 콘크리트학회지
• /
• 제6권2호
• /
• pp.169-179
• /
• 1994

주택건설은 극심한 건축자재 부족과 인력수급등의 많은 어려움을 격고 있는데, 이에 대한 문제의 해결방은 중 하나로 철근콘크리트 공사에서 철근의 가공조립공정을 보다 간소화하면서 그 기능의 효율성을 높이는 방법으로 구조용 용접철망과 루프형 용접철망을 이용한 공법이 제기되고 있다. 본 연구에서는 일방향 슬래브에 콘크리트 예상 압축강도가 $210kg/cm^2$일 때, 최대균열폭과 소성변형 능력에 영향을 미치는 요인인 사용철근의 종류, 최소철근비를 기준으로 한 인장철근비(${\rho}t$), 주변지지조건, 겹이음길이의 4가지 주요변수로 하여 슬래브의 구조적 특성 및 휨거동을 파악하는데 그 목적을 두었다. 연구결과, 소성변형능력은 이형철근을 사용한 슬래브가 용접철망을 사용한 슬래브보다 월등히 큰 것으로 나타났고, 겹이음된 슬래브에서는 겹이음길이 30D가 적절한 것으로 나타났다. 또한 최대균열폭은 용접철망과 루프형 용접철망을 사용한 슬래브가 이형철근을 사용한 슬래브 보다 균열폭을 억제하는 것으로 나타났다.

• Geomechanics and Engineering
• /
• 제12권4호
• /
• pp.689-705
• /
• 2017

The present study deals with the Pressure-settlement behavior of square and rectangular skirted footing resting on sand and subjected to a vertical load through a laboratory experimental study. A series of load tests were conducted in the model test tank to evaluate the improvement in pressure-settlement behavior and bearing capacity of square and rectangular model footings with and without structural skirt. The footing of width 5 cm and 6 cm and length/width ratio of 1 and 2 was used. The relative density of sand was maintained at 30%, 50%, 70%, and 87% respectively. The depth of skirt was varied from 0.25 B to 1.0 B. All the tests were carried out using a strain controlled loading frame of 50 kN capacity. The strain rate for all test was kept 0.24 mm/min. The results of present study reveal that, the use of structural skirt improves the bearing capacity of footing significantly. The improvement in bearing capacity was observed almost linearly proportional to the depth of skirt. The improvement in bearing capacity of skirted footings over footing without skirt was observed in the range of 33.3% to 68.5%, 68.9% to 127% and 146.7% to 262% for a skirt depth of 0.25 B, 0.50 B and 1.0 B respectively. The skirted footings were found more effective for sand at relative density of 30% and 50% than at relative density of 70% and 87%. The bearing capacity was found to increase linearly with footing width for footings with and without skirts. This observation was found to be consistent for footings with different skirt depths and for relative density of sand i.e., 30%, 50%, 70%, and 87%. The obtained results from the study for footing with and without skirts were comparable with available solutions from literature.

• 한국축산시설환경학회지
• /
• 제5권2호
• /
• pp.79-86
• /
• 1999

Recently more dairy farmers are interested in the utilization of stretch film for wrapping silage material. Most of stretch film are imported from abroad and one domestic product was developed, but its quality has not yet been tested. Therefore this study was executed to offer basic data on this material to the farmers. Measured items were tensile load, extension ratio, and tear propagation strength of stretch films. Comparisons were made among the white color of domestic product(Kw), and white(Fw), black (Fb) and green color(Fg) of foreign products. The result were summarized as follows: 1. Tensile loads of lengthwise direction in stretch films were 557.4, 377.4, 282.6 and 398.4kgf/$\textrm{cm}^2$ in Kw, Fw, Fb and Fg, respectively, and tensile loads of width direction were 415.9, 418.1, 360.2 and 433.0kgf/$\textrm{cm}^2$ in Kw, Fw, Fb and Fg, respectively. 2. Extension ratios of lengthwise direction were 650, 462.5, 512.5% and 537.5% in Kw, Fw, Fb and Fg, respectively, Extension ratios of width direction were 930, 962.5, 950 and 1,000% in Kw, Fw, Fb and Fg, respectively. 3 Tear propagation strength of lengthwise direction 187.9, 148.9, 157.3 and 142.8kgf/cm, and tear propagation strength of width direction were 141.4, 129.8, 140.4 and 106.6kgf/cm in Kw, Fw, Fb and Fg, respectively. 4. In the light transmittance, there was no difference between white and green color stretch film, but it was very low in black one. Therefore, it is thought that research on quality of roll bale silage treated with each stretch film would be needed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.462-467
• /
• 2007

From the research which it sees verification of the whole interpretation and local interpretation of the durability steel deck bridge a static test and it produces the test body which it sells with character and it executes smallness pul lek detailed interpretation it leads and the appropriate characteristic of smallness pul lek detailed interpretation and to sleep a nominal stress price and it compares it judges it does. The stress quality from each structure region which it follows in load stock location it analyzes and from the hazard which evaluates, the objective region the length rib and the bottom grater weld zone, the length rib and width rib connection department and the width rib with the father it divided. It investigated the stress distribution of the test body from these objective location, FEM interpretation it led and the conduct against each structure state tax it analyzed. General conduct the load stock location the floor plate is located in the center with interpretation price together symmetry characteristic to seem, it cannot be like that it cannot there is one actual test price. Like this reason the length rib and width rib connection actually production even production characteristic security it is a day when it is impossible with the curvature junction department which it blows, it follows in examination body deferment condition and form feed with the fact that it is visible a big difference even with error of some it becomes. Consequently for a data and the research which are more accurate it is judged with the fact that the effort which is prudent will be necessary.

• 콘크리트학회논문집
• /
• 제21권5호
• /
• pp.549-556
• /
• 2009

이 연구에서는 프리캐스트 콘크리트 구조시스템에서 기존에 사용되고 있는 벽체의 수직접합부의 시공 및 문제점을 최소화하기 위해 접합부의 폭을 100 mm에서 150 mm로 증가시키고 연결방식을 3가지로 하여 구조적 성능 및 적용성에 대해 분석하였다. 또한, 해석적으로 구조적 성능을 파악하기 위해 비선형 유한 요소 해석법으로 분석하였다. 분석 결과, 광폭형 연결부를 가진 접합부를 적용하였을 때, PC벽체에 가해지는 하중을 더 효율적으로 철근이 분담하여 내력이 증가하고 연성적인 거동을 하는 것으로 나타났다. 또한, 접합부 루프근의 단면적이 커질수록 그리고 철근 개수가 증가할수록 최대내력이 증가하며 광폭형 접합부 형식 중에 용접형-링형-C형의 순서로 내력이 큰 것으로 나타났다. 용접형의 경우 현장조건에 따른 변화가 발생할 수 있으므로 광폭형 연결 부위를 링형 접합부로 하는 것이 안정적인 거동을 하며 현장 용접의 철저한 품질관리가 필요하다.