• Journal of electromagnetic engineering and science
• /
• 제18권3호
• /
• pp.188-198
• /
• 2018

In this study, we propose an approach for the design and satisfy the requirements of the fabrication of a small, lightweight, reliable, and stable ultra-wideband receiver for millimeter-wave bands and the contents of the approach. In this paper, we designed and fabricated a stable receiver with having low noise figure, flat gain characteristics, and low noise characteristics, suitable for millimeter-wave bands. The method uses the chip-and-wire process for the assembly and operation of a bare MMIC device. In order to compensate for the mismatch between the components used in the receiver, an amplifier, mixer, multiplier, and filter suitable for wideband frequency characteristics were designed and applied to the receiver. To improve the low frequency and narrow bandwidth of existing products, mathematical modeling of the wideband receiver was performed and based on this spurious signals generated from complex local oscillation signals were designed so as not to affect the RF path. In the ultra-wideband receiver, the gain was between 22.2 dB and 28.5 dB at Band A (input frequency, 18-26 GHz) with a flatness of approximately 6.3 dB, while the gain was between 21.9 dB and 26.0 dB at Band B (input frequency, 26-40 GHz) with a flatness of approximately 4.1 dB. The measured value of the noise figure at Band A was 7.92 dB and the maximum value of noise figure, measured at Band B was 8.58 dB. The leakage signal of the local oscillator (LO) was -97.3 dBm and -90 dBm at the 33 GHz and 44 GHz path, respectively. Measurement was made at the 15 GHz IF output of band A (LO, 33 GHz) and the suppression characteristic obtained through the measurement was approximately 30 dBc.

• 한국전자파학회논문지
• /
• 제20권9호
• /
• pp.900-905
• /
• 2009

본 논문에서는 전류 블리딩(bleeding)과 입력 인덕티브 직렬-피킹을 이용한 공통 드레인 귀환(Common Drain Feedback: CDFB) CMOS 광대역 저잡음 증폭기(Low Noise Amplifier: LNA)를 설계하였다. 캐스코드 증폭기와 귀환 증폭기를 DC 결합하여 블리딩 전류의 조정을 통해 LNA의 이득과 잡음 지수(Noise figure: NF)의 동적 제어를 실현하였다. 제작한 LNA는 2.5 GHz의 대역폭에서, 고이득 영역은 $1.7{\sim}2.8\;dB$ NF와 17.5 dB 이득, 그리고 27 mW의 전력 소비를 보이고, 저 이득 영역은 $2.7{\sim}4.0\;dB$ NF와 14 dB 이득, 그리고 1.8 mW의 전력 소비를 보인다.

• 한국전자파학회논문지
• /
• 제21권10호
• /
• pp.1143-1153
• /
• 2010

본 논문에서는 마이너스 군지연 회로를 이용하여 아날로그 RF 피드백 증폭기의 선형성 개선 대역폭을 증가시킬 수 있는 새로운 방법을 제안한다. 피드백 증폭기는 피드백 경로의 전달 시간 오차로 인하여 선형성 개선 대역폭이 제한되며, 그로 인하여 강력한 선형성 개선 효과에도 불구하고 거의 사용되지 않고 있다. 선행 연구를 통해 설계된 마이너스 군지연 회로의 군지연 특성을 응용하여 기존의 피드백 구조의 한계인 군지연 정합 문제를 해결하였다. 제작된 피드백 증폭기에 2-carrier Wideband Code Division Multiple Access (WCDMA) 신호를 인가하여 측정한 결과, WCDMA 기지국 하향 대역의 50 MHz 대역 전반에 걸쳐서 15 dB 이상의 선형성 개선 효과를 얻을 수 있었다. 평균 출력 전력이 28 dBm일 때 5 MHz 이격된 주파수에서 측정된 인접 채널 누설비(Adjacent Channel Leakage Ratio: ACLR)는 최대 25.1 dB 개선되어 -53.2 dBc로 측정되었다.

• 대한전자공학회논문지SD
• /
• 제41권12호
• /
• pp.7-12
• /
• 2004

본 논문에서는 0.1 $\mum$ InGaAs/InAlAs/GaAs Metamorphic HEMT (High Electron Mobility Transistor)를 이용하여 DC~45 GHz 대역의 광대역 MIMIC(Millimeter-wave Monolithic Integrated Circuit) 분산 증폭기를 설계 및 제작하였다. MIMIC 증폭기의 제작을 위해 Metamorphic HEMT(MHEMT)를 설계 및 제작하였으며, 제작된 MHEMT는 드레인 전류 밀도 442 mA/mm, 최대 전달컨덕턴스(Gm)는 409 mS/mm를 얻었다. RF 특성으로 fT는 140 GHz fmax는 447 GHz의 양호한 성능을 나타내었다. 광대역 MIMIC 분산 증폭기의 설계를 위해 MHEMT의 소신호 모델과 CPW 라이브러리를 구축하였으며, 이를 이용하여 MIMIC 분산 증폭기를 설계하였다. 설계된 분산 증폭기는 본 연구에서 개발된 MHEMT MIMIC 공정을 이용하여 제작하였으며, MIMIC 분산 증폭기의 측정결과, DC ~ 45 GHz대역에서 6 dB 이상의 S21 이득을 얻었으며, 입력반사 계수는 45 GHz에서 -10 dB, 출력반사계수는 -7 dB의 특성을 나타내었다. 제작된 분산 증폭기의 칩 크기는 2.0 mm$\times$l.2 mm다.

• 대한전자공학회논문지TC
• /
• 제42권9호
• /
• pp.49-56
• /
• 2005

RF 전력증폭기 및 Doherty 전력증폭기의 열 메모리 효과는 변조신호의 대역폭과 동작 전력의 레벨에 따라 민감하게 영향을 미친다. 본 논문에서는 전기적인 비선형성을 정확히 모델링하고 열 메모리 효과가 Doherty 증폭기의 왜곡형성에 어떤 영향을 미치는지에 대해 연구하였다. Doherty 증폭기의 열 메모리 특성을 모델링하기 위하여 순시적으로 소모되는 전력과 순시 접합온도의 정확한 관계식을 정립하여 제안하였다. 제안된 모델의 파라미터는 서로 다른 여기상태에 따라 전력증폭기의 특성이 결정되는데, 트랜지스터의 열 메모리 효과는 대역폭이 넓은 W-CDMA 및 UMTS 시스템에서 충분히 고려되어야 한다. 이러한 열 메모리 효과를 사전왜곡 함수에 적응하여 선형화된 전력증폭기의 출력스펙트럼에서 최대 20 dB정도의 ACLR 개선효과를 보인다. 측정결과는 60W급 LDMOS Doherty 전력증폭기로 측정하였으며, 열 메모리 보상기는 ADS로 검증하였다.

• ETRI Journal
• /
• 제30권3호
• /
• pp.377-382
• /
• 2008

A novel power amplifier for a polar transmitter is proposed to achieve better spectral performance for a wideband envelope signal. In the proposed scheme, 2-bit sigma-delta (${\Sigma}{\Delta}$) modulation of the envelope signal is introduced, and the power amplifier configuration is modified in a binary form to accommodate the 2-bit digitized envelope signals. The 2-bit ${\Sigma}{\Delta}$ modulator lowers the noise of the envelope signal by fine quantization and thus enhances the spectral property of the RF signal. The Ptolemy simulation results of the proposed structure show that the spectral noise is reduced by 10 dB in a full transmit band of the EDGE system. The dynamic range is also enhanced. Since the performance is improved without increasing the over-sampling ratio, this technique is best suited for wireless communication with high data rates.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권3호
• /
• pp.312-318
• /
• 2016

This paper presents a 2-6 GHz GaN HEMT power amplifier monolithic microwave integrated circuit (MMIC) with bridged-T all-pass filters and output-reactance-compensation shorted stubs using the $0.25{\mu}m$ GaN HEMT foundry process that is developed by WIN Semiconductors, Inc. The bridged-T filter is modified to mitigate the bandwidth degradation of impedance matching due to the inherent channel resistance of the transistor, and the shorted stub with a bypass capacitor minimizes the output reactance of the transistor to ease wideband load impedance matching for maximum output power. The fabricated power amplifier MMIC shows a flat linear gain of 20 dB or more, an average output power of 40.1 dBm and a power-added efficiency of 19-26 % in 2 to 6 GHz, which is very useful in applications such as communication jammers and electronic warfare systems.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.818-823
• /
• 2014

A high-gain wideband low noise amplifier (LNA) using $0.25-{\mu}m$ Gallium-Nitride (GaN) MMIC technology is presented. The LNA shows 8 GHz to 15 GHz operation by a distributed amplifier architecture and high gain with an additional common source amplifier as a mid-stage. The measurement results show a flat gain of $25.1{\pm}0.8dB$ and input and output matching of -12 dB for all targeted frequencies. The measured minimum noise figure is 2.8 dB at 12.6 GHz and below 3.6 dB across all frequencies. It consumes 98 mA with a 10-V supply. By adjusting the gate voltage of the mid-stage common source amplifier, the overall gain is controlled stably from 13 dB to 24 dB with no significant variations of the input and output matching.

• Journal of Electrical Engineering and Technology
• /
• 제7권1호
• /
• pp.81-85
• /
• 2012

This paper presents a wideband and low-noise direct conversion front-end receiver supporting VHF and UHFbands simultaneously. The receiver iscomposed of a low-noise amplifier (LNA), a down conversion quadrature mixer, and a frequency divider by 2. The cascode configuration with the resistor feedback is exploited in the LNA to achieve a wide operating bandwidth. Four gainstep modesare employed using a switched resistor bank and a capacitor bank in the signal path to cope with wide dynamic input power range. The verticalbipolar junction transistors are used as the switching elements in the mixer to reduce 1/f noise corner frequency. The proposed front-end receiver fabricated in 0.18 ${\mu}m$ CMOS technology shows very low minimum noise figureof 1.8 dB and third order input intercept pointof -12dBm inthe high-gain mode of 26.5 dBmeasured at 500 MHz.The proposed receiverconsumeslow current of 20 mA from a 1.8 V power supply.

• 전기전자학회논문지
• /
• 제18권1호
• /
• pp.19-24
• /
• 2014

We report stable, wideband, flat-topped, 10 GHz optical frequency comb generation from a semiconductor-based mode-locked ring laser with an intra-cavity high finesse Fabry-Perot etalon. We demonstrate a stable 10 GHz comb with greater than 200 lines within a spectral power variation below 1 dB, which is the largest value obtained from a similar mode-locked laser in our knowledge. Greater than 20 dB of the spectral peak to deep ratio at 0.02 nm resolution, ~92 femtosecond timing jitter over 1 kHz to 1 MHz range, and non-averaged time traces of pulses confirm very stable optical frequency comb lines.