• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.1-9
• /
• 2022

In the current study, in order to understand the dynamic response characteristics of the system according to the external acoustic forcing, a numerical approach was developed by adding an sign-sweep forcing function to the existing network model. Through this model, the sensitivity of frequency and pressure amplitude changes according to system parameters such as the physical dimensions and boundary conditions of the target combustor was analyzed in a wide frequency range. Analysis results of dynamic response characteristics of the target combustor are shown that the frequency regime with high dynamic pressure response was similar to the instability frequency range measured in the same combustor, and in particular, the response of the system depends greatly on the location of the acoustic forcing source term.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.4
• /
• pp.270-274
• /
• 2006

A color filter array (CFA) helps a single electrical image sensor to recognize color images. The Red-Green-Blue (RGB) Bayer CFA is commonly used, but the amount of the light which arrives at the photodiode is attenuated with this CFA. Red-White-Blue (RWB) CFA increases the amount of the light which arrives at photodiode by using White (W) pixels instead of Green (G) pixels. However, white pixels are saturated earlier than red and blue pixels. The pseudo multiple capture scheme and the corresponding RWB CFA were proposed to overcome the early saturation problem of W pixels. The prototype CMOS image sensor (CIS) was fabricated with $0.35-{\mu}m$ CMOS process. The proposed CIS solves the early saturation problem of W pixels and increases the dynamic range.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.389-393
• /
• 2003

This paper describes the design of enhanced TSSI RF Power Detector which has wide dynamic range using switch and Log amp. This Power Detector consists of low and high gain loops, and they adaptively switched by output DC voltage which is proportioned to input power level. Because Power Detector needs to separate the channel, so architecture is heterodyne system having 70MHz intermediate frequency. This proposed RF Power Detector is settle to the satisfaction of Closed loop power control system for W-CDMA optic repeater, and the obtained dynamic range cover the higher than 50dB.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1671-1675
• /
• 2012

In this paper, we fabricate multi-channel receiver for radar system. This receiver at X-band can be received 8 signal of an identical characteristic, dynamic range has more than 80[dB]. To process direct received signals, this system has the built-in two digital de-modulators which offer the minimum loss on the receiving signal path and has high stability by adding Built-In Test. The gain, noise figure, difference of amplitude and phase on the signal path is respectively $14{\pm}2$[dB], 19[dB], ${\pm}2$[dB], $10^{\circ}$ and below.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.1
• /
• pp.73-80
• /
• 2008

An improved method to measure the dynamic viscoelastic properties of elastomers is proposed. The method is based on the analysis of forced oscillation of a cylindrical sample loaded with inertial mass. No special equipment or instrumentation other than the ordinary vibration measurement apparatus is required. Typical measurement of the viscoelastic properties of a silicone rubber $Silastic^{(R)}$ S2 were measured over the wide frequency range from 10 Hz to 3 kHz under the action of wide region of deformation from $10^{-4}%$ to 5%. It was shown that modulus of elasticity and loss tangent fall on the single curves when the ratio of load mass to sample mass changed from 1 to 20.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.525-530
• /
• 2003

This paper is concerned with a control allocation strategy using the dynamic inversion which generates the nominal control input trajectories, and autopilot design using the time-varying control technique which is time-varying version of pole placement of linear time-invariant system for an agile missile with aerodynamic fin and thrust vectoring control. Dynamic inversion can decide the amount of the deflection of each control effector, aerodynamic fin and thrust vectoring control, to extract the maximum performance by combining the action of them. Time-varying control technique for autopilot design enhance the robustness of the tracking performance for a reference command. Nonlinear simulations demonstrates the dynamic inversion provides the effective nominal control input trajectories to achieve the angle of attack command, and time-varying control technique exhibits good robustness for a wide range of angle of attack.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1997.10a
• /
• pp.47-53
• /
• 1997

Dynamic models have been developed for the coal gasification process by using a modular approach method. The complete unit is divided, for the convenience of the analysis, into several sections, viz. the coal feeding system, the gasifier, the gas cooler, the valves, the pumps, etc. The dynamic behaviour of each section is described in mathematical terms and each term is modulized into several submodels consisting of the complete process. To represent the behaviour of the fluid flow, the hydraulic network is proposed. Results for the more important system variables are presented and discussed. There dynamic models enable process and control engineers to quickly review a wide range of alternative operating and control strategies and help operators to easily understand the process dynamics and eventually can be applied to the design of commercial scale IGCC plants.

• Journal of applied mathematics & informatics
• /
• v.24 no.1_2
• /
• pp.399-409
• /
• 2007

In this paper we use iterative dynamic programming in the discrete case to solve a wide range of the nonlinear equations systems. First, by defining an error function, we transform the problem to an optimal control problem in discrete case. In using iterative dynamic programming to solve optimal control problems up to now, we have broken up the problem into a number of stages and assumed that the performance index could always be expressed explicitly in terms of the state variables at the last stage. This provided a scheme where we could proceed backwards in a systematic way, carrying out optimization at each stage. Suppose that the performance index can not be expressed in terms of the variables at the last stage only. In other words, suppose the performance index is also a function of controls and variables at the other stages. Then we have a nonseparable optimal control problem. Furthermore, we obtain the path from the initial point up to the approximate solution.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.42-48
• /
• 2002

Experiments were conducted to determine the structural dynamic characteristics of bump foil bearing. The housing of the bearing on the journal was driven by two shakers which were used to simulate dynamic forces acting on the bump foil strips. Three different bump foils(Cu-coated bump, silicon bump, viscoelastic bump) are tested and the dynamic coefficients of three bump foils compared, based on the experimental measurements for a wide range of operating conditions. From the test results, the high damping coefficients of viscoelastic bump are achieved and the possibility of the super-bending-critical operation is suggested.

• Structural Engineering and Mechanics
• /
• v.87 no.2
• /
• pp.129-136
• /
• 2023

In this paper, dynamic buckling of truncated conical shell made of carbon nanotubes (CNTs) composite is studied. In aerospace industries, this category of structures is utilized extensively due to wide range of engineering applications. To calculate the effective material properties of the nanocomposite, The Mori-Tanaka model is applied. Also, the motion equations are derived with the assistance of the first order shear deformation theory (FSDT), Hamilton's principle and energy method. Besides, In order to solve motion equations and analyze dynamic instability region (DIR) of the structure, mixed model of differential quadrature method (DQM) and Bolotin's method is used. Moreover, investigation of the different parameters effects such as geometrical parameters and volume fraction of CNTs on the analysis of the DIR of the structure is done. In accordance with the obtained results, the DIR will occur at higher frequencies by increasing the volume fraction of CNTs.