• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.715-718
• /
• 2008

An in-line wet etch/cleaning system was established for the research and development in wet etch process. The system was equipped with a reverse moving system for the reduction in the size of the in-line wet etch/cleaning system and it was possible for the glass substrate to be moved back and forth and alternated in a wet etch bath. For the comparison of the effect of the normal motion and that of the alternating motion on the in-line wet etch process, indium tin oxide(ITO) pattern was obtained through both wet etch process conditions. The results showed that the alternating motion is not inferior to the normal motion in etch rate and in etch uniformity. It is concluded that the alternating motion is possible to be applied to the in-line etch process.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.327-331
• /
• 2008

An in-line wet etch/cleaning system was established for the research and development in wet etch process as a formation of electrode such as metal or transparent conductive oxide layer. A reverse moving system was equipped in the in-line wet etch/cleaning system for the alternating motion of glass substrate in a wet etch bath of the system. Therefore, it was possible for the glass substrate to be moved back and forth and it was possible to reduce the size of the system by using the reversing moving system. For the effect of the alternating motion of substrate on the etch rate in the in-line wet etch bath, indium tin oxide(ITO) patterns were obtained through wet etch process in the in-line system in which the substrate was moved back and forth. From the CD(critical dimension) skews resulted from the ADI CD and ACI CD of the ITO patterns, it was concluded that the alternating motion of glass substrate are possible to be applied to the mass production of wet etch process.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.352-354
• /
• 1995

The optical and electrical properties of High Speed AlGaAs infrared LED by using metal wet etch process instead of metal lift-off process are investigated. The power out increases when metal contact is patterned by wet etch process. Forward voltage and Reverse voltage for metal wet etch process represent higher value than the metal lift-off process. The aging effect of power out also indicates good results with wet etch process. The wet etch process for metal contact reveals reliable LED device properties.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.863-866
• /
• 2008

For the cost reduction in the fabrication of display panels, a reverse moving system was equipped to a compacted in-line wet etch/cleaning system. For the effect of the alternating movement of substrate on the wet etch process, ITO layers were etched in various moving modes of substrates and the results were compared and analyzed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.105-109
• /
• 2002

The wet etching characteristics of magnetic materials such as NiFe and CoFe were investigated in terms of etch rate and etch profile by using variouus etching solutions (etchants). Among the various etching solutions, HNO$_3$, HCl, and H$_2$SO$_4$were selected for the etching of magnetic materials and showed distinct results. In the case of NiFe films, faster etch rate were obtained with HNO$_3$solution. When NiFe films ere etched with HCl solution, white etch residues were found on the surface of etched films. From FEAES analysis of these etch residues, they were proved to be by-product from the reaction of NiFe with Cl element. CoFe thin films showed the similar trend to the case of NiFe films. They were etched fast in HNO$_3$ solution while Chl solution represented slow etching. The etch profiles of CoFe films showed smooth etch profile but revealed the partial etching around the patterns in HNO$_3$solution of relatively high concentration. It was observed that the etched surface was clean and smooth, and that white etch residues were also remained on the etched films.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.32-38
• /
• 2004

Laser-induced thermochemical wet etching of titanium in phosphoric acid has been investigated to examine the feasibility of this method fur fabrication of microstructures. Cutting, drilling, and milling of titanium foil were carried out while examining the influence of process parameters on etch width, etch depth, and edge straightness. Laser power, scanning speed of workpiece, and etchant concentration were chosen as major process parameters influencing on temperature distribution and reaction rate. Etch width increased almost linearly with laser power showing little dependence on scanning speed while etch depth showed wide variation with both laser power and scanning speed. A well-defined etch profile with good surface quality was obtained at high concentration condition. Fabrication of a hole, micro cantilever beam, and rectangular slot with dimension of tess than 100${\mu}{\textrm}{m}$ has been demonstrated.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.146-150
• /
• 2021

Plasma information based virtual metrology (PI-VM) that predicts wafer-to-wafer etch rate variation after wet cleaning of plasma facing parts was developed. As input parameters, plasma information (PI) variables such as electron temperature, fluorine density and hydrogen density were extracted from optical emission spectroscopy (OES) data for etch plasma. The PI-VM model was trained by stepwise variable selection method and multi-linear regression method. The expected etch rate by PI-VM showed high correlation coefficient with measured etch rate from SEM image analysis. The PI-VM model revealed that the root cause of etch rate variation after the wet cleaning was desorption of hydrogen from the cleaned parts as hydrogen combined with fluorine and decreased etchant density and etch rate.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.410-414
• /
• 2013

We report the wet etching of titanium nickel (TiNi) films for the production of nano-electro-mechanical (NEM) device. $SiO_2$ and $Si_3N_4$ have been selected as sacrificial layers of TiNi metal and etched with polyethylene glycol and hydrofluoric acid (HF) mixed solution. Volume percentage of HF are varied from 10% to 35% and the etch rate of the $SiO_2$, $Si_3N_4$ and TiNi are reported here. Within the various experiment results, 15% HF mixed polyethylene glycol solution show highest etch ratio between sacrificial layer and TiNi metal. Especially $Si_3N_4$ films shows high etch ratio with TiNi films. Wet etching results are measured with SEM inspection. Therefore, this experiment provides a novel method for TiNi in the nano-electro-mechanical device.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.2
• /
• pp.271-275
• /
• 2008

The MAM(Megasonic Agitated Module) has been fabricated for improving the characteristics of wet etching. The characteristics of the MAM are investigated during the wet etching with and without megasonic agitation in this paper. The adoption of the MAM has improved the characteristics of wet etching, such as the etch rate, etch uniformity, and surface roughness. Especially, the etching uniformity on the entire wafer was less than ${\pm}1%$ in both cases of Si and glass. Generally, the initial root-mean-square roughness($R_{rms}$) of the single crystal silicon was 0.23nm. Roughnesses of 566nm and 66nm have been achieved with magnetic stirring and ultrasonic agitation, respectively, by some researchers. In this paper, the roughness of the etched Si surface is less than 60 nm. Wet etching of silicon with megasonic agitation can maintain nearly the original surface roughness during etching. The results verified that megasonic agitation is an effective way to improve etching characteristics of the etch rate, etch uniformity, and surface roughness and that the developed micromachining system is suitable for the fabrication of devices with complex structures.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.831-833
• /
• 2008

150 nm thick Ga-doped ZnO thin film, which was deposited by a sputtering process, was wet-chemically etched by using various organic acids such as oxalic, citric and formic acid. Wet etch parameters including etchant concentration and temperature are investigated for each etchant, and their effects on the etch rate and the feature of edge line are compared.