• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.2
• /
• pp.52-57
• /
• 2003

The charcoal is known to have gas adsorption capability and electrical properties. Some practical applications of carbon materials for the purpose of limited electrical conduction were made in these days. In this paper, we applied the several different kinds of charcoal to the papers in three different ways to investigate if charcoal application method affects its electrical conduction capability. Wet end addition, making multiply, and coating method were tested. The area electrical resistivity of charcoal containing paper was measured. The strength properties of charcoal containing paper were compared to those of the control, which had no charcoal in it. Experimental results showed that manufacturing conditions of the charcoal itself changed its electrical and strength properties of charcoal containing paper. The electrical properties of charcoal containing paper can be used for the removal of electrostatic problem in packaging system. The strength property of the charcoal containing paper should be kept, at least, over the minimum requirement for the packaging system. By using coating method on paper or making multiply, strength loss of paper by inclusion of charcoal could be overcome.

• Journal of Pharmaceutical Investigation
• /
• v.22 no.3
• /
• pp.205-210
• /
• 1992

In order to develop a controlled-release oral drug delivery system (DDS) of theophylline (TP), microporous membrane-coated tablets were prepared and evaluated in vitro and in vivo. Rapidly water-soluble core tablets of TP (300 mg) were prepared by wet granulation and compression technique, Then the core tablets were spray-coated with polyvinylchloride (PVC) in which micronized sucrose particles were dispersed. Effect of formula compositions of coating suspensions on the pharmaceutical characteristics such as membrane strength and dissolution was investigated in vitro. The membranes remained unbroken in pH 1.2 buffer at $37^{\circ}C$ at least for 2 hours after the disintergration test. TP was released from the coated-released tablets at a zero-order rate over 8 hours. The release at pH 1.2 and 4.0 was similar in rate but a little more rapid than that at pH 6.8. The coated tablets were administered to three healthy male volunteers and their saliva profiles of TP were compared with those from the commercial sustained release TP tablets such as Slobid and Asconthin. Saliva TP concentrations from the coated tablets were successfully sustained over 48 hours after the dosing and were comparable to those of the commercial sustained-release tablets. The membrane-coating technique is very simple and does not need any sophisticated equipments. In this respect, the membrane-coated tablets may be superior to the commercial sustained-release tablets and this technique is worth adopting by the pharmaceutical industries.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.249-249
• /
• 2015

Silver films have been of considerable interest for years due to their better performance relative to other metal films for engineering applications. A series of multi-layer silver coatings with different thickness (i.e. 0.3 um to 1.5 um) were prepared on Aluminium substrate containing copper undercoat by direct current (DC) magnetron sputtering method. For the comparative purpose, similar thickness silver coatings were prepared by electrolytic deposition method. Microstructural, morphological, and mechanical characteristics of the silver coatings were evaluated by means of scanning electron microscope (SEM), X-ray diffraction (XRD), Surface roughness test, microhardness test and nano-scratch test. From the results, it has been elucidated that the silver films prepared by DC magnetron sputtering method has superior properties in comparison to the wet coating method. On the other hand, DC magnetron sputtering method is relatively easier, faster, eco-friendly and more productive than the electrolytic deposition method that uses several kinds of hazardous chemicals for bath formulation. Therefore, a New Work Item Proposal (NWIP) for the test methods standardization of DC magnetron sputtered silver coatings has recently been proposed via KATS, Korea and a NP ballot is being progressed within a technical committee "ISO/TC107-metallic and other inorganic coating".

• Corrosion Science and Technology
• /
• v.8 no.6
• /
• pp.243-250
• /
• 2009

When a steel sheet pipe applied to marine environment, an anti-corrosive coating should be treated to obtain long-term life-time for steels, especially, splash zone. Although anti-corrosive property of coatings is required to be tested in real marine environment, it is difficult because of long test time such as 20 years or more time. Therefore, we used cyclic corrosion tester in a laboratory, which has similar conditions with salt-dry-wet process such as real marine environment. Anti-corrosive properties of the coatings and two steels were tested their anti-corrosive properties under cyclic corrosion test conditions(KS D ISO 14993) and the results were compared with estimate life-time in real marine environment. According to cyclic corrosion test, accelerated corrosive factor of each anti-corrosive coating was investigated accelerated corrosive factor from impedance with EIS method. Accelerated corrosive factor of type SS400 carbon steel and A690 was also investigated their accelerated corrosive factor from the regression curves of weigh loss results. One of the anti-corrosive coatings showed about 50 years life-time compared with standard sample life-time. Carbon steel SS400 showed from 0.1 mm/yr to 0.06 mm/yr as its corrosion rate.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.489-492
• /
• 2004

In this paper, we demonstrate polymer thin-film transistors (TFTs) on a paper-based flexible substrate. As a substrate, commercially available photo-paper is used with Parylene coating. The parylene layer enables conventionally used wet chemical process and vacuum deposition processes for electrodes and gate insulator. As an active channel layer, we used poly-3-hexylthiophene (P3HT) which is solution process. Field effect mobility up to $(0.06 {\pm} 0.02) cm^2/Vs$ and on/off ratio of $10^3 {\~}10^4$ are achieved on a photo-paper.

• Journal of the Korean Ceramic Society
• /
• v.15 no.2
• /
• pp.89-97
• /
• 1978

The basic mechanism of adherence in sintered high purity alumina ceramic-to-metal bonding was studied. Emphasis was placed on flux composition, porosity of the fired ceramics, and metallizing mixtures. The study was conducted on 95 and 99.5% alumina, using molydbenum-manganese, molybdenum-manganese-silicon dioxide metallizing compositions. Metallizing was performed in wet hydrogen (dew point, ＋17$^{\circ}C$) at 145$0^{\circ}C$ for 45min. This experiment indicated that adhernece mechanism of ultra high purity alumina ceramic was attributed to formation of $MnAl_2O_$4, and in the case of 95% alumina containing glass, the migration of glass from the interface into the void of the metal coating was the main role to the adhrence. It showed also that greater the bond-strength was resulted as porosity was increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.12 s.255
• /
• pp.1196-1202
• /
• 2006

A MEMS methanol reformer was fabricated and its performance was evaluated in the present study. Catalytic steam reforming of methanol was selected because the process had been widely applied in macro scale reformers. Conventional Cu/ZnO catalyst that was prepared by co-precipitation method to give the highest coating quality was used. The reactor structure was made by bonding three layers of glass wafers. The internal structure of the wafer was fabricated by the wet-etching process that resulted in a high aspect ratio. The internal surface of the reactor was coated by catalyst and individual wafers were fusion-bonded to form the reactor structure. The internal volume of the microfabricated reactor was $0.3cm^3$ and the reactor produced exhaust gas with hydrogen concentration at 73%. The production rate of hydrogen was 4.16 ml/hr that could generate power of 350 mW in a typical PEM fuel cell.

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.119-123
• /
• 2016

We discussed various cover glass substrates available for photovoltaic (PV) modules, and investigated the fabrication methods of light trapping structures for the efficiency enhancement of PV modules: wet and dry etching or laser and direct patternings. We also introduced the analysis of haze at etched glass surfaces as a function of wavelength and also presented a anti-reflection coating technology for PV module.

• Analytical Science and Technology
• /
• v.5 no.1
• /
• pp.73-77
• /
• 1992

The quantitative analysis experiment of Zn-Fe electroplated steel was carried out by means of glow discharge spectrometry. The experimental results of chemical composition and coating weight of the Zn-Fe layer were compared with those obtained by the wet chemical analysis method. It has been found that those results obtained by two different methods agreed well with each other.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.9
• /
• pp.1348-1350
• /
• 2010

Conidia of Beauveria bassiana ARSEF-7060, produced in millet amended with plant oils such as sunflower, corn, or cotton seed oil, were exposed to $45^{\circ}C$ of wet heat for 90 min. Conidia from millet+corn oil medium had the highest thermotolerance [$LT_{50}$ (median survival time): 45.7 min]. The mycotized millet grains were coated with each of the same plant oils as a granular formulation and subjected to $50^{\circ}C$ of dry heat for 8 h. Corn oil coating ($LT_{50}$: 8.68 h) was superior to sunflower and cotton seed oil coatings, suggesting the feasibility of using corn oil to increase conidial thermotolerance.