• Journal of Conservation Science
• /
• v.18 s.18
• /
• pp.63-74
• /
• 2006

All rock materials of the three storied stone pagoda in Seoakri were composed of light gray alkali granite with medium grained and developed with small mialolitic cavities. This stone pagoda is preserving almost archetype except the head part because there was repair work already. But, foundation, basement and roof rocks are serious state by microbial invasion such as lichens. Because there are tree and grass that cause direct effect to stone pagoda surrounding. Therefore, conservation treatment executed the primary dry cleaning and secondary wet cleaning treatment. Stone surface is partly not removed well such as lichens which part removed using cleansing device that use high temperature steam. Some treated part concrete and epoxy resin remove and retreatment with mixing talc and alkali granite powder to epoxy resin. Did color matching at mixing process of epoxy resin and fillers to properties with set the feel of a material. Also, drainage ditched to minimize inflow of rainwater fall from slope that is on the east of stone pagoda, tree and grass in stone pagoda surrounding wished to do remove and control occurrence of lichens hereafter minimizing moisture conteats.

• YAKHAK HOEJI
• /
• v.41 no.3
• /
• pp.305-311
• /
• 1997

Sustained release-microspheres and immediate release-pellets were prepared to develop a controlled release multiparticulate system containing both water soluble and insoluble dr ug. Pseudoephedrin.HCl (EPD) and terfenadine (TRF) were used as model drugs, respectively. Sustained release-EPD microspheres were prepared by solvent evaporation method using Eudragit RL or RS as a matrix combined with pH-insensitive film coating. Smaller EPD microspheres were obtained when smaller amount of Eudragit as a matrix material or larger amount of magnesium stearate as a dispersing agent was used. However the obtained microspheres did not show syfficient sustained release characteristics. About 97% of EPD was released after 1 hr irrespective of matrix material used. Subsequent coating of the microspheres with pH-insensitive polymer such as Eudragit RS or ethylcelulose (EC) resulted good sustained in 37.5, 73.3 and 92.0% release of encapsulated EPD in distilled water after 1, 3 abd 7 hr, respectively. It corresponds to mean dissolution time (MDT) of 2.3 hr, which is much larger than that of un-coated EPD microspheres (0.0048 hr). Immediate release TRF pellets were prepared by spherically agglomerated crystallization using Eudragit E as an inert matrix and methylene chloride as a liquid binder. Using Eudragit E alone as a matrix resulted in satisfactory physical properties of the pellets such as sphericity, surface texture and flowability, but led to slower release of TRF from pellets than un-modified TRF powder (MDT of 1.70 vs 1.43 hr in pH 1.2 dissolution medium). Introducing propylene glycol or sodium lauryl sulfate as an emulsifier brought about faster release of TRF from pellets (MDT of 1.14 and 0.95 hr, respectively). In conclusion, microencapsulation by solvent evaporation combined with film coating and spherically agglomerated crystallization were successfully utilized to prepare controlled release multiparticulate system composed of sustained release EPD-microspheres and immediate release TRF pellets.

• Korean Journal of Weed Science
• /
• v.14 no.4
• /
• pp.252-257
• /
• 1994

The sprouting characteristics of Scirpus planiculmis and storage methods of corm for the herbicide screening were investigated under both laboratory and greenhouse conditions. Sprouting and elongation of S. planiculmis corms were continued during storage at low temperature ($5^{\circ}C$) and wet condition. However, sprouting of corm was failed when the surface water was removed from the corm, and elongation was reduced by the treatment of 0.5-1.0% sodium chloride(NaCl) solution. Alternate temperature was more effective on the sprouting of S. planiculmis corm than constant temperature. Optimum temperature for the sprouting of S. planiculmis corm was alternation between $25^{\circ}C$ to $35^{\circ}C$. Storage at $-20^{\circ}C$ for 10 min. or 14.7% dehydration made the corm of S. planiculmis to fail for sprouting. S. planiculmis corm was more tolerant to sodium chloride than Echinochloa crus-galli or Oryza sativa(Donginbyeo) seeds. Sprouting rate was decreased by cutting of the corm. Sprouting percent by vertical cuttings, horizontal cuttings, and vertical plus horizontal cuttings were 72, 56, and 28%, respectively.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.3
• /
• pp.179-186
• /
• 2009

Relation between soil salinity and forage yield of five upland crops such as sudan grass, sesbania, barnyard grass, corn and soybean was studied in the three reclaimed lands of Korea during two years from 2007 to 2008. Although plant number emerged was obtained satisfactory by desalting treatment, further growth of crops was sharply affected by re-salting process according to soil drying. Soil salinity varied place by place and changed constantly, crop growth was differently responded to soil salinity according to the specific conditions of the reclaimed lands. In the Iweon reclaimed land with higher soil water conductivity and sandy soil texture, crop growth and yield sharply decrease with increase of soil salinity. Relation between soil salinity and crop growth and yield was well expressed as logarithmic function. Surface soil EC to reach at 50% of growth reduction to the tallest height of crops was $5dS\;m^{-1}$ for soybean, $6dS\;m^{-1}$ for corn and $7dS\;m^{-1}$ for sudan grass, sesbania, and barnyard grass by logarithmic function. In the Hwaong and Yeongsangang reclaimed lands with low soil conductivity and finer soil texture, plant growth response to salt stress was statistically vague by mixing of harmful influence from flooding and wet injury. However, it is observed that crop growth and yield on the place of lower salinity was better than crop growth on the place of higher salinity. It is accordingly concluded that flooding control during summer rainy season is vary important as well as desalting process for good growth of soiling and forage crops in the newly reclaimed land from tidal flat.

• Korean journal of applied entomology
• /
• v.29 no.4
• /
• pp.244-251
• /
• 1990

Three viral insecticides were differently formulated with a nuclear polyhedrosis virus isolated from Spdodoptera litura by addition of feeding attractant, anti-precipitate of polyhedra, spreading agent, and UV-protectants. Sucrose was effective for attraction of larval feeding to increase the mortality and for protection of polyhedra from inactivation by sunlight when added 1% to 5% of sucrose solution to the formulations. Contents of additives to the formulations were 0.5% in polyvinyl alcohol to prohibit the precipitation of polyhedra and 0.1% in Triton X-100 to spread and wet the formulations to the plant. Inactivation of the virus under sunlight was decreased when added 800g of white carbon to 100 L of water in the white carbon formulation and 30% of molasses to the molasses's. In the formulation of white carbon and molasses mixtures, activation of the virus was increased when mixtured 500g of the former with 10% of the latter. Three formulations were persisted their pathogenicity more than 95% of mortality at 3 days p.i. Encapsulation of the polyhedral surface was more distinctively coated with the carbon and showed more effective in the residual effects of the white carbon than others, but the molasses more attractive for larval feeding.

• Geophysics and Geophysical Exploration
• /
• v.2 no.2
• /
• pp.96-103
• /
• 1999

Most of saline water inousions have been diagnosed by geophysical or geochemical approach independently. The objective of this study is to provide the effective method to detect the saline water intrusion on the ground water in the vicinity of seashore using these two methods. Schulumberger sounding, frequency domain electromagnetic sounding and geochemical analysis of ground water were carried out to explore saline water intrusion. Schulumberger sounding was implemented in dry surface condition before irrigation water was introduced into the field, while electromagnetic sounding was carried out in wet ground condition after the irrigation. The purpose of duplicated measurements on the equivalent spot at different times was to investigate the variation of anomaly zone depending on the amount of ground water. It was possible to discriminate the anomalous zone due to high water saturation from the low electric resistivity zone by high salt concentrations through this way. For the verification of the geophysical result, the ground water samples in the study area were collected and analysed at the 23 points near the measuring spots. The groundwater at the spot nearest to the sea water intrusion identified by geophysical method indicates higher salinity than the standard limit concentration for agricultural irrigation water (250 mg/1). Isotope analysis of $D({^2}H)$ vs. is ${^18}O$ and PCA analysis were used to discriminate the anthropogenic pollution from those of high salinity from sea water intrusion.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.250-255
• /
• 2011

In this study, by using the polymeric membrane separation process, the $CO_{2}/CH_{4}$ separation and $H_{2}S$ removal from biogas were performed in order to $CH_{4}$ purification and enrichment for the fuel cell energy source application. Fibers were spun by dry/wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a porous, sponge substructure. The permeance of $CO_{2}$ and $CO_{2}/CH_{4}$ selectivity increased with pressure and temperature. Mixture gas with increasing pressure and temperature, removal efficiency of the $CO_{2}$ and $H_{2}S$ were decreased while concentration of $CH_{4}$ was increased up to 100%. When retentate flow rate was increased with the decreasing of pressure and temperature the $CH_{4}$ recovery ratio in retentate side was increased while the $CH_{4}$ purity in retentate side was decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.418-418
• /
• 2008

The electrochemical etching of silicon in HF-based solutions is known to form various types of porous structures. Porous structures are generally classified into three categories according to pore sizes: micropore (below 2 nm in size), mesopore (2 ~ 50 nm), and macropore (above 50 nm). Recently, the formation of macropores has attracted increasing interest because of their promising characteristics for an wide scope of applications such as microelectromechanical systems (MEMS), chemical sensors, biotechnology, photonic crystals, and photovoltaic application. One of the promising applications of macropores is in the field of MEMS. Anisotropic etching is essential step for fabrication of MEMS. Conventional wet etching has advantages such as low processing cost and high throughput, but it is unsuitable to fabricate high-aspect-ratio structures with vertical sidewalls due to its inherent etching characteristics along certain crystal orientations. Reactive ion dry etching is another technique of anisotropic etching. This has excellent ability to fabricate high-aspect-ratio structures with vertical sidewalls and high accuracy. However, its high processing cost is one of the bottlenecks for widely successful commercialization of MEMS. In contrast, by using electrochemical etching method together with pre-patterning by lithographic step, regular macropore arrays with very high-aspect-ratio up to 250 can be obtained. The formed macropores have very smooth surface and side, unlike deep reactive ion etching where surfaces are damaged and wavy. Especially, to make vertical microwire or nanowire arrays (aspect ratio = over 1:100) on silicon wafer with top-down photolithography, it is very difficult to fabricate them with conventional dry etching. The electrochemical etching is the most proper candidate to do it. The pillar structures are demonstrated for n-type silicon and the formation mechanism is well explained, while such a experimental results are few for p-type silicon. In this report, In order to understand the roles played by the kinds of etching solution and mask patterns in the formation of microwire arrays, we have undertaken a systematic study of the solvent effects in mixtures of HF, dimethyl sulfoxide (DMSO), iso-propanol, and mixtures of HF with water on the structure formation on monocrystalline p-type silicon with a resistivity with 10 ~ 20 $\Omega{\cdot}cm$. The different morphological results are presented according to mask patterns and etching solutions.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.3
• /
• pp.246-254
• /
• 2013

This study is purposed to verify the safety of the floor of the children's playground using polyolefin foam waste and rubber paving. The critical fall height, walking suitability, long term physical fatigue expectation and slipperiness were tested. Polyolefin foam wastes in thickness of 30mm, 50mm and 70mm were prepared with paving the rubber paving materials in 12mm and 15mm thickness respectively. The test on the critical fall height was carried out according to KS G 5758:2009. The floor hardness test equipment (O-Y HMA) was used for the test on hardness of the floor from a viewpoint of walking suitability and fatigue. A portable slipperiness tester (ONO PPSM) was used for slipperiness test. It was revealed from the test that the floor made of the polyolefin foam waste and rubber paving were considerably safe from a viewpoint of impact absorption. With regards to the hardness of the floor, it was shown the excellent performance in the aspects of walking and fatigue for male. But it was not suitable with walking on the shoes(middle heels) for female. And they will be very fatigue if they were in a long time walking or standing. As far as the slipperiness is concerned, it was shown that it was comparatively safe for the ordinary motions even though the surface was wet.

• Korean Journal Plant Pathology
• /
• v.3 no.4
• /
• pp.252-260
• /
• 1987

Incidence of lettuce drop was observed throughout the growing season in the vinylhouse at the southern part of Korea, Kimhai. Occurrence of this disease was especially severe at the seedling stage. Number of sclerotia in surface soil $(30\times30\times5cm)$ was 22.0 at the seedling stage, and 5.3 at harvest in the infected area. Temperature for mycelial growth ranged from 5 to $30^{\circ}C$ with optimum temperature at $25^{\circ}C$. Sclerotia were formed fewer at low temperature, but their size was larger resulting in heavier dry weight than that at high temperature. The apothecia were formed from the sclerotia that were buried in March, April and September upto 3cm soil depth, but formed from those buried only 1 em soil depth in October. Sclerotia buried in June and December did not form apothecia regardless of soil depth by 90 days. The sclerotia buried in the 5cm of soil depth did not form apothecia. Sclerotia that were embedded in wet or flooded soil at $25^{\circ}C$ and $30^{\circ}C$ for 5 weeks lost their viability. Infection of lettuce was possible with mycelia originated from sclerotia on autoclaved lettuce plant fragments. The fungus was pathogenic on 25 plant species in 8 families in artificial inoculation tests. Lettuce seedlings appeared to be infected by airborne ascospore originated from sclerotia on crops and weeds around paddy fields, because sclerotia existing in soil might perish under long flood conditions during rice cultivation.