• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.63-68
• /
• 2005

In this paper, Coplanar Waveguide(CPW) low-pass filter with the spurious-reduced is designed by using Defected Ground Structures(DGS). Two different LPF unit cells and DGS pattern are combined to reduce the spurious. In comparison to a conventional step impedance LPF, the size of proposed LPF as 17.2mm*6.8mm is several times smaller. The simulation and measurements confirm that spurious characteristics is presented less than -30dB($S_{21}$) to three times cut off frequency.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.370-374
• /
• 2002

This paper describes the design and fabrication of distributed analog phase shifter circuit. The phase shifter consist of coplanar waveguide(CPW) lines that are periodically loaded with voltage tunable (Ba,Sr)TiO$_3$ thin film interdigital(IDT) capacitors deposited by the pulsed laser deposition(PLD) on (001) MgO single crystals. The phase velocity on these IDT loaded CPW lines is a function of applied bias voltage, thus resulting in analog phase shifting circuits. The measured differential phase shift is 48$^{\circ}$ and the insertion loss decreases from -5㏈ to -3㏈ with increasing bias voltage from 0 to 40 V at 100㎐.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.5
• /
• pp.285-289
• /
• 2003

This paper proposes a 10 ${\mu}{\textrm}{m}$ thick oxide air-bridge structure which can be used as a substrate for RF circuits. The structure was fabricated by anodic reaction, complex oxidation and rnicrornachining technology using TMAH etching. High quality films were obtained by combining low temperature thermal oxidation (50$0^{\circ}C$, 1 hr at $H_2O$/O$_2$) and rapid thermal oxidation (RTO) process (105$0^{\circ}C$, 2 min). This structure is mechanically stable because of thick oxide layer up to 10 ${\mu}{\textrm}{m}$ and is expected to solve the problem of high dielectric loss of silicon substrate in RF region. The properties of the transmission line formed on the oxidized porous silicon (OPS) air-bridge were investigated and compared with those of the transmission line formed on the OPS layers. The insertion loss of coplanar waveguide (CPW) on OPS air-bridge was (about 1 dB) lower than that of CPW on OPS layers. Also, the return loss of CPW on OPS air-bridge was less than about - 20 dB at measured frequency region for 2.2 mm. Therefore, this technology is very promising for extending the use of CMOS circuitry to higher RF frequencies.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1133-1136
• /
• 2002

We designed and fabricated a low local oscillation (LO) power V-band CPW mixer module using a CPW-to-waveguide transition technology for the application of millimeter-wave wireless communication systems. The mixer was designed using a unique gate mixing architecture to achieve simultaneously a low LO input power, a high conversion gain, and good LO-RF isolation characteristics. The fabricated mixer exhibited a high conversion gain of 2 dB at a low LO power of 0 dBm. For data transmission of the 60 ㎓ wireless LNA systems, we fabricated a CPW-to-waveguide converter module of WR-15 type and mounted the fabricated mixer in the converter module. The fabricated V-band mixer exhibited a higher conversion gain and a lower LO input power than other reported V-band mixers.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.6
• /
• pp.11-19
• /
• 1997

For the circuit modeling of th ecoplanar waveguide (CPW) discontinuities, th eequivalent inductance is analyzed via the 3-dimensional boundary element method. The proposed method utilizes the magnetic scalar potential to obtain the magnetic flux passing sthrough the air-dielectric interfaces of the coplanar waveguide. The boundary integral is simplified by use fo the symmetry when the substrate is composed of the nonmagnetic material. In the numerical analysis, linear basis function and the collocationscheme are employed. The short-end and the step discontinuities are cahracterized through the calculations of the equivalent inductance andd the capacitance. The present method avoids the usual vector formulation and is quite advantageous in the quasi-staic characterization of the CPW disconditnuities.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.212-216
• /
• 2004

In this paper, a new design for a Coplanar Waveguide(CPW) fed wide-band slot antenna is presented. To enhance the impedance bandwidth of the slot antenna, we proposed the tapering slot structure. A various resonance modes are generated in the tapering slot. The measured impedance bandwidth of the proposed antenna is about 13:1(2.0 GHz∼25.9 GHz) with VSWR$\leq$2. Simulation and measurement results for return loss and radiation pattern are presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.278-281
• /
• 1999

We designed and fabricated a travelingwave CPW(coplanar waveguide) electrode for LiNbO$_3$ optical modulator. To Investigate the variation of microwave refractive index of these electrodes, we prepared the CPW electrode samples as a function of electrode thickness and measured the TDR and S-parameter. From this results, we could know the electrode conditions of index matching to 2.20 for 1150 nm optical wave index for applying LiNbO$_3$ optical modulator. Also we discussed the some properties of CPW electrode for applying LiNbO$_3$ optical modulator.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.64-71
• /
• 2000

An optical switch composed of identical, equally-spaced $Ti:LiNbO_3$ three-waveguides was designed and fabricated. Patterned Ti was diffused into z-cut $LiNbO_3$ substrates. $SiO_2$ buffer layer was evaporated to reduce the propagation loss of TM mode, and Al electrodes of CPW structure were built on the layer for switching of the guided beam. The optical switching phenomenon was confirmed when a beam of ${\lambda}=1.3{\mu}m$ was launched into the center waveguide and an electric field was applied to detune the three waveguides symmetrically.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.82-89
• /
• 2007

This paper presents a coplanar waveguide fed L-planar type monopole antenna which covers ultra wideband(UWB) region of 3.1 GHz to 10.6 GHz. The proposed UWB L-planar type monopole antenna is designed and implemented on the organic substrates( ${\varepsilon}_{r}=3.38,\;@10\;GHz$). The radiation elements, feed line, and ground planes of the antenna are printed on the same conductive layer of the substrates. The bandwidth of the proposed antenna is measured in the range of 3.0 GHz to 11.0 GHz. The measured radiation patterns are symmetrical in E-plane and omni-directional in H-plane. Antenna gains ranges from 1.4 dBi to 4.6 dBi. The proposed UWB antenna shows that the structure is adequate for the design of RFIC.

• Journal of Advanced Navigation Technology
• /
• v.20 no.1
• /
• pp.59-64
• /
• 2016

This paper presents a high dividing ratio unequal dualband divider using coplanar waveguide (CPW) and shunt connected open stub transmission lines. In order to implement transmission lines for a dualband divider using design equations, the low impedance lines of divider can be realized a shunt connected open stub transmission line. Also, the high impedance lines are realized by CPW transmission lines. To certify the validity of an unequal dualband divider using CPW and shunt connected open stub transmission lines, the 10:1 unequal dualband divider is implemented at operating frequency of 1 and 2 GHz. Good experimental performance at each frequency are obtained, which are in good agreement with the simulated results.