• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.1
• /
• pp.29-33
• /
• 1977

Impedance of a post mount structure supporting a microwave diode in the X-band rectangular waveguide is calculated by using the induced EMF method. Probe measurement of the driving point impedance of the post mounu shows a close agreement with the theoretical calulation when the gap of the post mount is near the bottom wall of the waveguide.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.218-221
• /
• 1989

Buried Bragg reflectors which are immune to the contamination of the surface of an optical waveguide chip are fabricated on Si3N4-SiO2 rib optical waveguides on Si. The effective refractive indices and the bandwidths of the fabricated buried Bragg reflector waveguides are determined by transmission measurement. We show that the measured values of the effective refractive indices are consistent with the calculated values as the width of the waveguide rib varies. Propagation losses of the guided modes due to the leakage into the si substrate are also calculated.

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.9-14
• /
• 2011

In this study, the internal structure of an optical waveguide embedded in a flexible optical circuit board is observed with a confocal microscope. In order to increase the light reflection from an internal material interface with a very small index difference, and thus enhance the signal contrast, a theta microscopy scheme has been integrated into a conventional confocal microscope, and a high NA oil-immersion lens has been used. The interface reflectivity is increased from roughly 0.0015% to 0.025% by the proposed method, and the internal structure can thus be successfully measured.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.270-277
• /
• 2013

In this paper, we propose a wideband ridge SIW(Ridge Substrate Integrated Waveguide)-to-SIW(Substrate Integrated Waveguide) transition. The proposed transition structure is designed to acquire a wide bandwidth by inserting through via holes at the regular interval for an impedance matching and an E-field mode matching method. The measurement results show a fractional bandwidth is 29.1 % at 20 dB return loss from the center frequency(11 GHz). The maximum insertion loss is 0.49 dB from 9.21 GHz to 12.41 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.9
• /
• pp.865-872
• /
• 2002

The conventional Rotman lens antenna using a waveguide lens has the bended waveguide from the inner lens contour to the antenna element. However in this paper the improved Rotman lens antenna having a straight waveguide is proposed. By applying this technique, the beam steering antenna for BMWS application which has 3 input ports and 6 antenna elements consisted of open-ended waveguide has been designed and fabricated. From the measurement, the gain of the beam steering antenna is 15.4 ~ 17.2 dB. The direction angle is 0$^{\circ}$, +14$^{\circ}$~ +16$^{\circ}$, -15$^{\circ}$~ -16$^{\circ}$ and the side lobe level is -l0 ~ 20 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.731-739
• /
• 2012

Transverse electric modes in parallel plate waveguide of which cut-off frequency is much lower than that of $TE_1$ and $TM_1$ mode generally known as the lowest higher order mode are investigated. Electric and magnetic field components of the modes are evaluated with the assumption that boundaries at both sides are perfect magnetic conductor. The existence of these modes are verified by simulation and experimental measurement of parallel plate waveguide cavity. Changed characteristics from the fact that the boundaries are imperfect are studied.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.2
• /
• pp.135-143
• /
• 2022

In this paper, the compact waveguide slot array antenna for interferometric radar altimeter is proposed. The proposed antenna structure consist of corrugation structure which is applied between each channel to improve isolation, three-channel waveguide slot array antenna and feeder. In addition, to reduce the occurrence of phase ambiguity, the baseline spacing of the three-channel antenna is analyzed and the results are applied to the design. For compact design, reduced height and SMP connector structure are used and the dip brazing method which is the conjugation method after dipping to flux is used for the fabrication of the lightweight antenna. The measurement result of the proposed antenna shows less than 1.41 : 1 (VSWR) and 48.3 dBc (isolation). The antenna gain is higher than 20.2 dBi and the side lobe levels are lower than 18.8 dB (vertical plane) and 10.0 dB (horizontal plane).

• ETRI Journal
• /
• v.45 no.2
• /
• pp.338-345
• /
• 2023

A filtering power divider based on air-filled substrate-integrated waveguide (AFSIW) technology is proposed in this study. The AFSIW structure is used in the proposed filtering power divider for substantially reducing the transmission losses. This structure occupies a large area because of the use of air as a dielectric instead of typical dielectric materials. A filtering power divider provides power division and frequency selectivity simultaneously in a single device. The proposed filtering power divider comprises three AFSIW cavities. The filtering function is achieved using symmetrical inductive posts. The input and output ports of the proposed circuit are realized by directly connecting coaxial lines to the AFSIW cavities. This transition from the coaxial line to the AFSIW cavity eliminates the additional transitions, such as AFSIW-SIW and SIW-conductor-backed coplanar waveguide, applied in existing AFSIW circuits. The proposed power divider with a second-order bandpass filtering response is fabricated and measured at 5.5 GHz. The measurement results show that this circuit has a minimum insertion loss of 1 dB, 3-dB fractional bandwidth of 11.2%, and return loss exceeding 11 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.335-342
• /
• 2012

A high-isolation Ka-band WR-28 waveguide power combiner is designed and implemented using a resistive septum. The waveguide power combiner developed here is an E-plane T-junction type with a TaN resistive septum inserted in a slit of waveguide junction. The fabricated waveguide power combiner shows a return loss better than -20 dB and an insertion loss less than 0.1 dB. Also the measurement shows isolation levels of 20 dB or more almost all over the band and in particular 25 dB or more below 37 GHz. The amplitude and phase imbalance are measured to be less than 0.1 dB and $2.5^{\circ}$, respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.159-165
• /
• 2018

In this paper, a low-loss wideband waveguide transducer is proposed for millimeter-wave communication and radar applications. A conventional E-plane probe transducer is generally designed using thin and flexible substrate at millimeter-wave frequencies, considering the very small waveguide size. However, it results in serious performance degradation caused by the bending of the substrate. In order to alleviate this problem and provide a reliable performance, we propose an extended E-plane probe transducer where the probe substrate is extended to and fix ed in the slit area formed in the waveguide wall. It is fabricated using $127{\mu}m$-thick substrate with dielectric constant of 2.2. The measurement in the back-to-hack configuration shows the excellent insertion loss of 1.35 dB (${\pm}0.35dB$) including the loss of 3 cm-long thru waveguide and return loss better than 13.8 dB over entire W-band (75-110 GHz). Therefore, it can be effectively applied for millimeter-wave high-speed communications and high-sensitivity radars.