• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.6
• /
• pp.478-484
• /
• 2019

The submarine cable for Yongsu wave power plant was cut in 2014 winter. This study investigated the probability of high-wave occurrence exceeding the 50-year return period and the underestimation of armor unit weight used to protect the cable. The observation data from KMA buoy and the hindcast wave data were reviewed to determine the return period of wave height during the winter. In order to investigate the armor unit weight of cable-protection, we calculated the required weight of armor unit using not only Design Standard for Harbor and Fishery Port, but also the previous researches for the wave with large incident angle. As a result, it appeared that the high wave exceeding the 50-year return period did not occur during the winter of 2014 and the armor unit weight of the cable protection was not sufficient to sustain the obliquely incident wave, which induced the cable protection failure.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.36 no.5
• /
• pp.528-534
• /
• 2003

The 2-D hydraulic experimental results for the submerged rubble-mound structure, we have been concerned with the slability/function characteristics of the structures by the effects of wave force, scour/deposition at the toe and the wave transmission ratio at the lee-side sea. So, to investigate the variation characteristics of the wave transmission ratio which depended on a geometrical structure of the submerged breakwater profiles, the critical conditions for the depth of submergence and crest width were obviously presented. In summary, the results lead us to the conclusion that the wave control capabilities of submerged breakwaters by the variation of the submergence depth is higher than about 4 times the degree at the efficiency than the that of crest width. The destruction of the covering block at the crest generated at the region which was located between the maximum and minimum damage curve, and it's maximum damage/failure station from the toe of the structure was $0.2\;L_s.$ As the wave transmission coefficient and the slope of the structure increase, the damage/failure ratio and the maximum scour depth at the toe was extended, respectively. When the maximum scour depth happened, the destruction of the covering block which was located at the toe generated at the front of the submerged rubble-mound breakwater. Finally, it was found from the results that the optimization of the structure may be obtained by the efficient decision of the submergence depth and crest width in the permissible range of the wave transmission ratio.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.255-264
• /
• 2009

Soils containing vanishing materials lead changes in the microstructure of particulate media due to water inflow. Thus, dissolution renders some local unstability. As the moisture contents decease, the component of the vanished materials may affects on the cementation of paniculate materials. This cementation phenomenon has a huge influence on the stiffness, strength and stability under lower stress level. The goal of this study is to introduce the cementation effects on a compressional wave velocity, a shear wave velocity, and the resonant frequency of shear waves. The glass bead and salt water with different mole contents are used. Test results show that the changes of shear and compressional wave velocities consist of three stages. In the first region, compressional wave velocities increase and shear wave velocities decrease with a decreases in reducing water contents from 100% to 90~95%. In the second region, shear and compressional wave velocities become stable at 90~95% to 10% of the water contents. In the third region, shear and compressional wave velocities increases dramatically with a decrease in the water content due to the capillary force and cementation of salt. Furthermore, the resonant frequency of the shear waves shows similar phenomenon. Specimens prepared by glass beads and salt water are proved to be able to provide a meaningful insight in under structural behaviors of the cementation.

• Ocean Systems Engineering
• /
• v.5 no.3
• /
• pp.139-160
• /
• 2015

The global performance of the 5MW OC4 semisubmersible floating wind turbine in random waves was numerically simulated by using the turbine-floater-mooring fully coupled and time-domain dynamic analysis program FAST-CHARM3D. There have been many papers regarding floating offshore wind turbines but the effects of second-order wave-body interactions on their global performance have rarely been studied. The second-order wave forces are actually small compared to the first-order wave forces, but its effect cannot be ignored when the natural frequencies of a floating system are outside the wave-frequency range. In the case of semi-submersible platform, second-order difference-frequency wave-diffraction forces and moments become important since surge/sway and pitch/roll natural frequencies are lower than those of typical incident waves. The computational effort related to the full second-order diffraction calculation is typically very heavy, so in many cases, the simplified approach called Newman's approximation or first-order-wave-force-only are used. However, it needs to be justified against more complete solutions with full QTF (quadratic transfer function), which is a main subject of the present study. The numerically simulated results for the 5MW OC4 semisubmersible floating wind turbine by FAST-CHARM3D are also extensively compared with the DeepCWind model test results by Technip/NREL/UMaine. The predicted motions and mooring tensions for two white-noise input-wave spectra agree well against the measure values. In this paper, the numerical static-offset and free-decay tests are also conducted to verify the system stiffness, damping, and natural frequencies against the experimental results. They also agree well to verify that the dynamic system modeling is correct to the details. The performance of the simplified approaches instead of using the full QTF are also tested.

• Journal of Wetlands Research
• /
• v.14 no.4
• /
• pp.439-455
• /
• 2012

Coupled wave induced current modeling system(WIC) was developed from combining with the nearshore spectral wave model, SWAN, the wave induced force model, WIF, and the flow model, EFDC. The reasonable results were obtained from WIC modeling system. The ratio of the wave height calculated with respect to refraction and diffraction effects over submerged spherical shoal was occurred approximately 1~5 % errors compared to Goda(2000)'s result. The radiation stress suggested by Longuet-Higgins and Stewart(1960), the stresses due to rollers in breaking waves proposed by Dally and Osiecki(1994), and Kim(2004)'s new spreading approach instead of the previous lateral mixing approach were added to calculate wave induced force. The results of the WIC modeling system show good agreement with Nishimura et al.(1985)'s laboratory measurements and better than Kim(2004)'s 2 dimensional depth averaged numerical computations for a plane beach with detached breakwater. The present flow field computed agrees reasonably well with the measured flow field. The relative merit of WIF model in WIC modeling system is unconditional stable for time increment.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.04a
• /
• pp.451-457
• /
• 2000

In many dynamic problems such as foundation vibrations ultrasonic nondestructive evaluation and blasting analysts are confronted with the problem of wave propagation in an infinite or semi-infinite media. In order to simulate this situation by a finite analytical model provisions must be made to absorb the stress waves arriving at the boundary. Absorbing boundaries are mathematical artifacts used to prevent wave reflections at the boundaries of discrete models for infinite media under dynamic loads. An analytical study is carried out to examine the effectiveness of Lysmer-Kuhlemeyer model one of the most widely used absorbing boundaries. Validity of the absorbing boundary conditions suggested by Lymer-Kuhlemeyer is examined by adopting the solution of Ewing et al. to the problem of plane waves from a harmonic normal force on the surface of an elastic half-space. The Ewing's problem is than numerically simulated using the finite element method on a semi-circular mesh with and without absorbing boundaries which are represented by viscous dashpots. The absorption ratios are calculated by comparing the displacements at the absorbing boundaries to those at the free field without absorbing boudaries.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.4
• /
• pp.17-26
• /
• 1996

A submerged vehicle which is a nonlinear multivariable system must be designed to be roubst against inner-outer perturbations and hydrodynamic disturbances induces maneuvering operation. But a practical design of motion controller is limited by both mathematical modeling error and linearization errors. Performance of a motion controller based on traditional design method is very poor when the vehicle motion is under wave force distrubacnes near sea surface. Therefore, this ppaer proposes a design method of $^{\infty}$ controller under model uncertainty and sea wave disturbances. performance of the controllers by both computer simulation and HILS (hardwave in the loop simulation) shows that $H^{\infty}$ controller is more robust than PID controller under model uncertainty and high sea state...

• Journal of the Korean Society of Safety
• /
• v.16 no.1
• /
• pp.9-17
• /
• 2001

The purpose of this research is to analyze the impact resposes(impulsive stress and strain etc.) of anisotropic materials subjected to the low-velocity impact. For this purpose, a beam finite element program based on modified higher-order beam theory for anisotropic materials are developed and used to simulate the dynamic behaviors [contact force, displacement of ball and target, strain(stress) response histories] according to the changes of material property, stacking sequence, velocity and dimension etc.. Test materials for simulation are composed of $[0^{\circ}/45^{\circ}/0^{\circ}/-45^{\circ}/0^{\circ}]_{2s} and [90^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}/90^{\circ}]_{2s}$ stacking sequences. Finally, the results of this simulation are compared with those of wave propagation theory and then the impact responses and wave propagation phenomena are investigated.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1415-1423
• /
• 2013

The traveling wave ultra-sonic motor (TWUSM) is operated through the frictional force between the rotor and the stator. Hence, the contact mechanism should be analyzed to estimate the motor performance. However, the nonlinearity of the contact mechanism of the TWUSM makes it difficult to propose a proper contact model and a characteristic analysis method. To address these problems, a novel contact model is proposed and be termed the cylindrical dynamic contact model (CDCM) in this research. An estimation method of the motor performance is proposed using the CDCM, an analytical method, and a numerical method. The feasibility and usefulness of the proposed characteristic analysis are verified through experimental data.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.118-120
• /
• 2003

The behavior of viscous fingerings caused by an external force is investigated by using a two­phase lattice Boltzmann method. The effects of the modified capillary number, the viscosity contrast, and the modified Darcy-Rayleigh number on the instability of interfaces are found. The calculated wave numbers are in good agreement with the theoretical ones in the range of wave numbers smaller than 10, but the calculated ones tend to become smaller than the theoretical ones in higher wave numbers.