• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.8
• /
• pp.915-928
• /
• 2011

Titanium for dental implant application has the superior properties of biocompatibility, specific strength, and corrosion resistance. However, it is extremely difficult to find a suitable surface treatment method for sufficient osseointegration with biological tissue/bone cell and implant surface. Surface treatment technology using laser has been researched as the way to increase surface area of implant. In this study, to develop the surface treatment process with improved adhesion between implant and bone cell at the same time for superior biocompatibility, pulsed laser beam was overlapped continuously for scribed surface morphology and determination of friction coefficient. As the results, surface area and friction coefficient was increased over 2 times by the comparison with sand blasting, which is used for the conventional method. In this time, the optimal condition for laser beam power and beam irradiation speed was 13 watt and 50 mm/sec, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.715-723
• /
• 2016

This paper proposes a design of optimal PI(D) controller for brushless DC (BLDC) motor speed control by the particle swarm optimization (PSO), one of the powerful metaheuristic optimization search techniques. The proposed control system is implemented on the TMS320F28335 DSP board interfacing to MATLAB/SIMULINK. With Back EMF detection, the proposed system is considered as a class of sensorless control. This scheme leads to the speed adjustment of the BLDC motor by PWM. In this work, the BLDC motor of 100 watt is conducted to investigate the control performance. As results, it was found that the speed response of BLDC motor can be regulated at the operating speed of 800 and 1200 rpm in both no load and full load conditions. Very satisfactory responses of the BLDC system can be successfully achieved by the proposed control structure and PSO-based design approach.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.8
• /
• pp.901-906
• /
• 2006

In this paper, the power amplifier using active bias circuits for LDMOS(Lateral Diffused Metal Oxide Semiconductor) MRF-21180 is designed and fabricated. According to change the temperature, the gate voltage of LDMOS is controlled by the fabricated active bias circuits which is made of PNP transistor to suppress drain current. The driving amplifier using MRF-21125 and MRF-21060 is made to drive the LDMOS MRF-21180 power amplifier. The variation of current consumption in the fabricated 60 watt power amplifier has an excellent characteristics of less than 0.1 A, whereas a passive biasing circuit dissipates more than 0.5 A. The implemented power amplifier has the gain over 9 dB, the gain flatness of less than $\pm$0.1 dB and input and output return loss of less than -6 dB over the frequency range 2.11 $\sim$ 2.17 GHz. The DC operation point of this power amplifier at temperature variation 0 $^{\circ}C$ to 60 $^{\circ}C$ is fixed by active bias circuit.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.242.2-242.2
• /
• 2014

Plasma-polymer thin films (PPTF) have been deposited on a Si(100) wafer and glass under several conditions such as different RF power by using plasma-enhanced chemical vapor deposition (PECVD) system. Ethylcyclohexane, ammonia gas, hydrogen and argon were utilized as organic precursor, doping gas, bubbler gas and carrier gases, respectively. PPTFs were grown up with RF (ratio frequency using 13.56 MHz) powers in the range of 20~60 watt. PPTFs were characterized by FT-IR (Fourier Transform Infrared), FE-SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope), Contact angle and Probe station. The result of FT-IR measurement showed that the PPTFs have high cross-link density nitrogen doping ratio was also changed with a RF power increasing. AFM and FE-SEM also showed that the PPTFs have smooth surface and thickness. Impedance analyzer was utilized for the measurements of C-V curves having different dielectric constant as RF power.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.443-452
• /
• 2002

A new phase shift full bridge (PSFB) converter with serially connected two transformers for telecommunication equipments of several hundred watts is proposed. The main features of the proposed converter are a wide input voltage range, an easiness to meet the requirement for zero voltage switching (ZVS) condition at a light load, and a small output voltage ripple. Furthermore, the serially connected two transformers can replace both a main transformer and an output inductor since the two transformers act as not only a main transformer but an output inductor by turns. Therefore, there is no need to use an output inductor, then the proposed converter features high power density. A mode analysis, design equations through a large signal modeling, and experimental results are presented to verify the validity of the proposed converter.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.12
• /
• pp.839-846
• /
• 1988

If we use the 2-dimensional analyzing method with the magnetic vector potential for the analysis of eddy current distribution in electric machinery, we can obtain the magnitude of eddy current but can't have the characteristic of eddy current distribution. For the settlement of this problem, we have induced the governing equation with the current vector potential and attemptted 2-dimensional analysis of eddy current distribution by finite element method. And the time domain weighted residual method is used in treatment of time differential term and we have developed the algorithm by it. And then, we analyze eddy current distributions of analytic model and aluminium disk in singlephase watt hour meter. Consequently we have verified the propriety and utility of above mentioned method.

• Journal of the Korean Magnetics Society
• /
• v.15 no.1
• /
• pp.48-52
• /
• 2005

This paper describes a current sensor for precision current measurement of an electronic watt-hour meter that is going to install in houses in the future. As the current sensor is based on an cored principle (the Rogowski principle) it is not subject to usual limitations of saturation and non-linearity of general current transformers. An advantage of the developed current sensor is that non-linearity error in low current range is improved and the construction can be kept simple using an air core. We present a magnetic field analysis of the sensor using a finite-element solver. We compared the measured values versus the calculated values.

• Journal of Biomedical Engineering Research
• /
• v.16 no.4
• /
• pp.447-456
• /
• 1995

As a part of electro-mechanical totally implantable artificial heart (TIAH) program, a transcut- aneous energy transmission system has been developed. By mutual magnetic induction between the first coil on the skin and the subcutaneously implanted second coil, the system transfers elctrical power through the skin. This research aimed at minimizing the size of the implanted part as well as maximizing the transfer efficiency. Using class I amplifier, we achieved above 75% power transfer efficiency at average 40W power transfer level which is required for normal TIAH operation. In vivo performance of the developed system and bio-compatibility of the material used in Implanted parts were evaluated through animal experiments.

• Journal of Oral Medicine and Pain
• /
• v.34 no.3
• /
• pp.257-260
• /
• 2009

Gingival hyperpigmentation may cause esthetic problems, especially in patients with a gummy smile. This report presents the use of the $CO_2$ laser for gingival depigmentation. Two cases presented with the same chief complaint of unesthetic gingiva caused by melanin hyperpigmentation. The $CO_2$ laser was setted at 0.8 watt, 40Hz, 0.01sec. The procedure were performed with non-contact mode in all pigmented areas. Ablation of the gingival hyperpigmentation areas were accomplished without any bleeding complications or postoperative pain. After 2 weeks and 4 weeks later, healing is completed and hyperpigmented gingiva appeared pink and firm.

• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.44-51
• /
• 2016

A commercial $0.25{\mu}m$ GaN process is used to implement 6-18 GHz wideband power amplifier (PA) monolithic microwave integrated circuits (MMICs). GaN HEMTs are advantageous for enhancing RF power due to high breakdown voltages. However, the large-signal models provided by the foundry service cannot guarantee model accuracy up to frequencies close to their maximum oscillation frequency ($F_{max}$). Generally, the optimum output load point of a PA varies severely according to frequency, which creates difficulties in generating watt-level output power through the octave bandwidth. This study overcomes these issues by the development of in-house large-signal models that include a thermal model and by applying distributed L-C output load matching to reactive matched amplifiers. The proposed GaN PAs have successfully accomplished output power over 5 W through the octave bandwidth.