• Applied Chemistry for Engineering
• /
• v.28 no.3
• /
• pp.339-344
• /
• 2017

Reaction characteristics and catalytic activities on reverse water gas shift (RWGS) reaction over $Pt/TiO_2$ catalyst and Pt based catalysts added promoters were investigated. It was confirmed that RWGS reaction activity was affected by the kind of supports and active metals and the $Pt/TiO_2$ catalyst showed the highest catalytic activity. From various inlet $CO_2$ concentration tests and also the evaluation of thermodynamic equilibrium conversion, the catalytic activity of $Pt/TiO_2$ catalyst could be evaluated objectively and it was found to be higher than that of commercial catalysts. The catalytic activity could increase by adding Ca and Na as promoters. The XPS analysis revealed that the catalytic activity is closely correlated with the electron density of surface active sites.

• Applied Chemistry for Engineering
• /
• v.20 no.2
• /
• pp.186-190
• /
• 2009

This study is purposed to analyze thermodynamic properties on the hydrogen production by dimethyl ether steam reforming. Various reaction conditions of temperatures (300~1500 K), feed compositions (steam/carbon = 1~7), and pressures (1, 5, 10 atm) were applied to investigate the effects of the reaction conditions on the thermodynamic properties of dimethyl ether steam reforming. An endothermic steam reforming competed with an exothermic water gas shift reaction and an exothermic methanation within the applied reaction condition. Hydrogen production was initiated at the temperature of 400 K and the production rate was promoted at temperatures exceeding 550 K. An increase of steam to carbon ratio (S/C) in feed mixture over 1.5 resulted in the increase of the water gas shift reaction, which lowered the formation of carbon monoxide. The maximum hydrogen yield with minimizing loss of thermodynamic conversion efficiency was achieved at the reaction conditions of a temperature of 900 K and a steam to carbon ratio of 3.0.

• Korean Chemical Engineering Research
• /
• v.51 no.4
• /
• pp.455-459
• /
• 2013

The fuel processor for the portable fuel cell includes multi-step processes consisting of hydrogen generator, heat generator and several CO clean-up stages. One of requirements of the fuel processor for portable fuel cell system is a rapid start-up time. Especially, the warm-up time for WGS reactor is crucial factors for total start-up time. In this paper, active heating protocol, which is the heating protocol of WGS reactor supplied by the oxidation of CO rich reformate in the initial stage, is used for a rapid start-up. The air stream fed to the inlet of WGS reactor rapidly oxidize the CO rich reformate in the WGS reactor. Therefore, CO concentration in reformate quickly stabilized at the desired concentration without CO surges.

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.420-424
• /
• 2019

In SNG (synthetic natural gas) process by proposed RIST(Research Institute of Industrial Science & Technology)-IAE(Institute for Advanced Engineering) (including three adiabatic reactors and one isothermal reactor), the methanation reaction and water gas shift (WGS) reaction take place simultaneously, and the supply of steam with syngas might control the temperature in catalyst bed and deactivate the catalyst. In this study for development of SNG process, the characteristics of the methanation reaction with a Ni-based catalyst by prepared RIST and using a low $H_2/CO$ mole ratio (including $CO_2$ 22%) are evaluated. The operating conditions ($H_2O/CO$ ratio of the $1^{st}$ adiabatic reactor, operating temperature range of $4^{th}$ isothermal reactor, etc.) were reflected the results from previous studies and in the same condition a pilot scale SNG process is carried out. As a results, the pilot scale SNG process is stable and the CO conversion and $CH_4$ selectivity are 100% and 96.9%, respectively, while the maximum $CH_4$ productivity is $660ml/g_{cat}{\cdot}h$.

• Clean Technology
• /
• v.29 no.4
• /
• pp.327-332
• /
• 2023

This study investigated synthesis gas production via steam reforming of biogas. Ni-Al₂O₃ and Ni-CeO₂ catalysts were synthesized using the co-precipitation method, with controlled precipitation agent injection rates. Catalytic performances were tested at various temperatures, with a gas composition ratio of CH₄:CO₂:H₂O = 1:0.67:3 and a gas hourly space velocity (GHSV) of 647,000 mL h^-1 gcat^-1. The rate of precipitation agent injection influenced the characteristics of the catalysts depending on the type of support used. As the temperature increased, both the CO₂ reforming of methane and the reverse water gas shift reactions occurred. The Ni-Al₂O₃ catalyst, synthesized with a single injection of the precipitation agent, exhibited the best catalytic activity under conditions with sufficient steam supply among the prepared catalysts, due to its high Ni dispersion.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.256-259
• /
• 2008

The gasification of biomass, sawdust, was carried out in order to investigate gasification characteristics. The experiment was performed using a down-draft fixed bed gasifier to surpass tar components generation in the gasification process. In the experiments, we investigated synthetic gas composition by varying reaction temperature, steam/carbon ratio, and excess ratio (ER), respectively. Higher reaction temperature, $700^{\circ}C$ to $900^{\circ}C$, could obtain higher $H_2$ yield. However, we could not obtain any meaning data by varying S/C ratio. Using $O_2$-LNG burner in the top of the gasifier may surpass water-gas shift reaction by increasing $CO_2$ concentration from the LNG-$O_2$ combustion reaction.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.507-510
• /
• 2008

Characteristics of an autothermal reformer at various operating parameters have been studied in this paper. Numerical method has been used, and simulation model has been developed for the analysis. Full Combustion reaction, Steam Reforming(SR) reaction, Water-Gas Shift(WGS) reaction, and Direct Steam Reforming(DSR) reaction are assumed as dominant chemical reactions in the autothermal reformer. Simulation results are compared with experimental results for code validation. Operating parameters of the autothermal reformer are inlet temperature, Oxygen to Carbon Ratio(OCR), Steam to Carbon Ratio(SCR), and Gas Hourly Space Veolcity(GHSV). SR reaction rate decreases with low inlet temperature. If OCR is increased, $H_2$ yield is increased but optimal point is suggested. WGS reaction is activated with high SCR. When GHSV is increased, reforming efficiency is increased but pressure drop may decrease the system efficiency.

• Environmental Engineering Research
• /
• v.13 no.4
• /
• pp.192-196
• /
• 2008

The generation of high purity hydrogen from reformed hydrocarbon fuels, or syngas, is essential for efficient operation of the fuel cell (PEMFC, Polymer Electrolyte Membrane Fuel Cell). Usually, major components of reformed gas are $H_2$, CO, $CO_2$ and $H_2O$. Especially a major component, CO poisons the electrode of fuel cells. The water gas shifter (WGS) that shifts CO to $CO_2$ and simultaneously produces $H_2$, was developed to a two stage catalytic conversion process involving a high temperature shifter (HTS) and a low temperature shifter (LTS). Also, experiments were carried out to reduce the carbon monoxide up to $3{\sim}4%$ in the HTS and lower than 5,000 ppm via the LTS.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.2
• /
• pp.168-178
• /
• 2009

To check feasibility of SEWGS(Sorption Enhanced Water Gas Shift) system, conceptual design and sensitivity analysis of operating variables have been investigated based on a design program of two-interconnected fluidized bed. Based on the conceptual design results, the optimum configuration for SEWGS was considered. Among three configurations, bubbling beds system was selected as the best configuration. Process design results indicate that the SEWGS system is compact and feasible. Based on the selected operating conditions, the effects of variables such as pressure, $CO_2$ capture capacity, solid inventory, CO conversion and $CO_2$ capture efficiency have been investigated as well.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.112-116
• /
• 2011

In this paper, a preconverter of MCFC for an emergence electric power supplier is numerically simulated to increase the hydrogen production from natural gas (methane). Commercial code is used to simulated the porous catalyst with user subroutine to model three dominant chemical reactions which are Stream Reforming(SR), Water-Gas Shift(WGS), and Direct Stram Reforming(DSR). To get 10% fuel conversion rate in preconverter. the required external heat flux is supplied from outer wall of preconverter. The calculated results show that very nonuniform temperature distribution and chemical reaction happen near the wall of preconverter. These phenomena can be explained by the low heat conductivity of porous catalyst and the endothermic reforming reaction.