• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.71-71
• /
• 2012

Memory 반도체 Test공정에서 사용되는 Probe Card의 Probing Area가 넓어지면서 종래에 사용되던 Cantilever제품의 사용이 불가능하게 되고, MEMS공정을 사용한 새로운 형태의 Advanced제품이 시장에 출현을 하였다. MEMS형의 제품은 다수의 Micro Spring을 MLC(Multi Layer Ceramic)위에 MEMS 공정을 사용하여 생성하는 방식으로서 MLC는 좁은 지역에 다수의 Pin을 생성 할 수 있는 공간을 만들어 주며, 또 다른 이유는 전기적 특성인 임피던스를 맞추고 다수의 Pin의 압력에 의하여 생기는 하중을 Ceramic기판으로 지탱하기 위한 목적도 있다. 이에 MLC와 같은 전기적 특성을 임피던스를 맞춘 RF-CPCB를 사용하여 작은 면적에 다수의 Pin접합이 가능한 방법을 마련한 후, 이 RF-PCB를 부착하여 Pin의 하중을 받는 Wafer와 유사한 열팽창을 갖는 Substrate를 사용하여 MLC를 대체하여 다양한 온도 조건에서 사용이 가능하며, 복잡하고 공정비가 많이 드는 MEMS 공정에 의한 일괄 Micro Spring 생성 공정을 전주 도금 또는 2D방식의 도금 Pin으로 대체하였으며, Probe Card의 중요한 물리적 특성인 Pin들의 정렬도를 마련하기 위해 Photo Process를 사용한 Wafer로 만든 Wafer Pin Array Frame을 사용하여 2D 제작 Pin을 일괄 또는 부분 접합이 가능한 방법으로 Probe Array Head를 제작하여 이들을 부착하여 Probe Array Head를 이전의 MEMS공정 방법에 비해 쉽고 빠르게 만들어 probe Card를 제작 할 수 있게 되었다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.3
• /
• pp.196-203
• /
• 2004

A three-dimensional (3D) IC technology platform is presented for high-performance, low-cost heterogeneous integration of silicon ICs. The platform uses dielectric adhesive bonding of fully-processed wafer-to-wafer aligned ICs, followed by a three-step thinning process and copper damascene patterning to form inter-wafer interconnects. Daisy-chain inter-wafer via test structures and compatibility of the process steps with 130 nm CMOS sal devices and circuits indicate the viability of the process flow. Such 3D integration with through-die vias enables high functionality in intelligent wireless terminals, as vertical integration of processor, large memory, image sensors and RF/microwave transceivers can be achieved with silicon-based ICs (Si CMOS and/or SiGe BiCMOS). Two examples of such capability are highlighted: memory-intensive Si CMOS digital processors with large L2 caches and SiGe BiCMOS pipelined A/D converters. A comparison of wafer-level 3D integration 'lith system-on-a-chip (SoC) and system-in-a-package (SiP) implementations is presented.

• Journal of Korean Institute of Industrial Engineers
• /
• v.36 no.2
• /
• pp.125-137
• /
• 2010

This study focuses on the problem of scheduling wafer lots of several product families in the deposition workstation in a semiconductor wafer fabrication facility. There are multiple identical parallel machines in the deposition workstation, and two types of setups, record-dependent setup and family setup, may be required at the deposition machines. A record-dependent setup is needed to find optimal operational conditions for a wafer lot on a machine, and a family setup is needed between processings of different families. We suggest two-phase heuristic algorithms in which a priority-rule-based scheduling algorithm is used to generate an initial schedule in the first phase and the schedule is improved in the second phase. Results of computational tests on randomly generated test problems show that the suggested algorithms outperform a scheduling method used in a real manufacturing system in terms of the sum of weighted flowtimes of the wafer lots.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2553-2556
• /
• 2003

In the semiconductor equipment industry, the SECS/GEM protocol has been recognized as the communication standard, but in our 300mm wafer aligner being developed, this capability has not been equipped yet. In this study, we present the realization of SECS-I, SECS-II and HSMS communication protocol between factory host computer and wafer aligner. Its validity is shown in actual test environment.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.374-377
• /
• 2002

Magnetic field is necessary to control the convection of melted silicon and to improve the quality of the wafer in the 12inch silicon wafer growing process. Nowadays, superconducting magnet is used in this process. We fabricated and tested a saddle shaped superconducting magnet for 8inch silicon wafer growing system. And the protection circuits for HTS current lead and superconducting coil are designed and manufactured. In this paper, their manufacturing process and test results are introduced.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.1
• /
• pp.15-19
• /
• 2003

Spin etcher can process frontside and backside on the wafer, which is used for etching, stripping, cleaning and wafer reclamation. A new generation of spin etchers has been designed to meet 300mm wafer processing. The larger header and higher spin speed make vibration problem a severe problem in developing equipments. This study shows schematic process of solving practical vibration problems, where it is required to analyze the principal ca uses of vibration problem and find out the method of vibration reduction in spin etcher. The vibration under normal operation is measured in time domain and is analyzed in frequency domain. And modal parameters are obtained through modal test. Using the modal parameters from experiments, the model of finite element method is formulated. From diagnosis using many measurements and analyses, it can be shown that main cause of vibration is unbalance of head.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.128-128
• /
• 2010

In this study, we investigated the evolution and reduction of the surface roughness during the high-speed chemical dry thinning process of Si wafers. The direct injection of NO gas into the reactor during the supply of F radicals from NF3 remote plasmas was very effective in increasing the Si thinning rate, due to the NO-induced enhancement of the surface reaction, but resulted in the significant roughening of the thinned Si surface. However, the direct addition of Ar and N2 gas, together with NO gas, decreased the root mean square (RMS) surface roughness of the thinned Si wafer significantly. The process regime for the increasing of the thinning rate and concomitant reduction of the surface roughness was extended at higher Ar gas flow rates. In this way, Si wafer thinning rate as high as $20\;{\mu}m/min$ and very smooth surface roughness was obtained and the mechanical damage of silicon wafer was effectively removed. We also measured die fracture strength of thinned Si wafer in order to understand the effect of chemical dry thinning on removal of mechanical damage generated during mechanical grinding. The die fracture strength of the thinned Si wafers was measured using 3-point bending test and compared. The results indicated that chemical dry thinning with reduced surface roughness and removal of mechanical damage increased the die fracture strength of the thinned Si wafer.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.466-472
• /
• 2007

A technology platform for wafer-level three-dimensional integration circuits (3D-ICs) is presented, and that uses wafer bonding with low-k polymeric adhesives and Cu damascene inter-wafer interconnects. In this work, one of such technical platforms is explained and characterized using a test vehicle of inter-wafer 3D via-chain structures. Electrical and mechanical characterizations of the structure are performed using continuously connected 3D via-chains. Evaluation results of the wafer bonding, which is a necessary process for stacking the wafers and uses low-k dielectrics as polymeric adhesive, are also presented through the wafer bonding between a glass wafer and a silicon wafer. After wafer bonding, three evaluations are conducted; (1) the fraction of bonded area is measured through the optical inspection, (2) the qualitative bond strength test to inspect the separation of the bonded wafers is taken by a razor blade, and (3) the quantitative bond strength is measured by a four point bending. To date, benzocyclobutene (BCB), $Flare^{TM}$, methylsilsesquioxane (MSSQ) and parylene-N were considered as bonding adhesives. Of the candidates, BCB and $Flare^{TM}$ were determined as adhesives after screening tests. By comparing BCB and $Flare^{TM}$, it was deduced that BCB is better as a baseline adhesive. It was because although wafer pairs bonded using $Flare^{TM}$ has a higher bond strength than those using BCB, wafer pairs bonded using BCB is still higher than that at the interface between Cu and porous low-k interlevel dielectrics (ILD), indicating almost 100% of bonded area routinely.

• Tribology and Lubricants
• /
• v.18 no.4
• /
• pp.260-266
• /
• 2002

In this study, the effects of oxide layer farmed on the wear tracks of TiN coated silicon wafer on friction and wear characteristics were investigated. Silicon wafer was used for the substrate of coated disk specimens, which were prepared by depositing TiN coating with 1 ${\mu}{\textrm}{m}$ in coating thickness. AISI 52100 steel ball was used fur the counterpart. The tests were performed both in air for forming oxide layer on the wear track and in nitrogen to avoid oxidation. This paper reports characterization of the oxide layer effects on friction and wear characteristics using X-ray diffraction(XRD), Auger electron spectroscopy(AES), scanning electron microscopy (SEM) and multi-mode atomic force microscope(AFM).

• Journal of Welding and Joining
• /
• v.18 no.6
• /
• pp.74-82
• /
• 2000

The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.