• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.418.2-418.2
• /
• 2016

$Al_2O_3$ passivation layer has excellent passivation properties at p-type Si surface. This $Al_2O_3$ layer forms thin $SiO_2$ layer at the interface. There were some studies about inserting thermal oxidation process to replace naturally grown oxide during $Al_2O_3$ deposition. They showed improving passivation properties. However, thermal oxidation process has disadvantage of expensive equipment and difficult control of thin layer formation. Wet chemical oxidation has advantages of low cost and easy thin oxide formation. In this study, $Al_2O_3$/$SiO_2/Si(100)$ interface was formed by wet chemical oxidation and PA-ALD process. $SiO_2$ layer at Si wafer was formed by $HCl/H_2O_2$, $H_2SO_4/H_2O_2$ and $HNO_3$, respectively. 20nm $Al_2O_3$ layer on $SiO_2/Si$ was deposited by PA-ALD. This $Al_2O_3/SiO_2/Si(100)$ interface were characterized by capacitance-voltage characteristics and quasi-steady-state photoconductance decay method.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.578-588
• /
• 1997

Poly-$Si_{1-x}Ge_x$ films on oxidized Si wafer were prepared by rapid thermal chemical vapor deposition using the $SiH_4$ and $GeH_4$ gaseous mixture at various deposition conditions. The deposition temperature, $SiH_4\;: GeH_4$ flow ratio and pressure were varied from 400 to $600^{\circ}C$, 1 : 0.1-2 : 1 and 1 to 50 torr, respectively. In this work, we have investigated the change of Ge composition of poly-$Si_{1-x}Ge_x$ films deposited with the variation of deposition parameters and the effect of Ge composition on the deposition rate. From the experimental results, it was observed that the deposition rate increased with increasing deposition temperature and Ge composition. On the other hand, the Ge composition decreased with increasing temperature. As the deposition pressure increased, the deposition rate and Ge composition were increased linearly to 10 torr but increased slowly above it, which has been attributed to the slower rate of surface reaction than mass transfer.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.260-266
• /
• 2002

DLC films were deposited on Si wafer by RF plasma assisted CVD using CH4 gas. Tribological tests were conducted using rotating type ball on disk friction tester in dry air. Four kinds of mating balls were used. The mating balls were made with stainless steel but apply different annealing conditions to achieve different hardness conditions. Testing results in all load conditions showed that the harder the mating materials, the lower the friction coefficient among the three kind of martensite mating balls. In case of austenite balls, the friction coefficients were lower than fully annealed martensite ball. The high friction coefficient in soft martensite balls seems to be caused by the larger contact area between DLC film and ball. The wear tracks of DLC films and mating balls could have proven that effect. Measuring the wear track of both DLC films and mating balls have similar tendency comparing to the results of friction coefficients. Wear rate of austenite balls were also smaller than that of fully annealed martensite ball. The results of effect of applying load showed, the friction coefficients were become decrease when the applying loads exceed critical load conditions. The wear track of mating balls showed that some material transfer occurs from DLC film to mating ball during the high friction process. Raman spectra analysis showed that transferred material was a kind of graphite and contact surface of DLC film seems to undergo phase transition from carbon to graphite during the high friction process.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.5
• /
• pp.307-311
• /
• 2009

In this study, TiCrN films were deposited on STS 316 Land Si (100) wafer by inductively coupled plasma (ICP) assisted D.C. magnetron sputtering. The effect R.F. power for ICP discharge on the mechanical properties of TiCrN films was investigated. XRD, XPS and FE-SEM were used for the structure analysis. Also the Micro-Knoop hardness tester and profilometer were used for measuring hardness of coatings and film stress respectively. As increasing the R.F. power for ICP discharge, thickness of coating was decreased from 1633 nm to 1288 nm but hardness was increased about $Hk_{5g}$ 4200 at 400 W. All of the XRD patterns showed (111), (200) and (220) peaks of TiCrN films. Surface morphology was studied using the profilometer. FE-SEM was used to know morphology and cross-section of the films. Structure of the films was changed dense as increased ICP power.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.217-222
• /
• 1998

Coating films of $SiO_2-TiO_2-AgO$ have been prepared on soda-lime-silica slide glasses and single crystal silicon wafer by the sol-gel method using a spin-coating technique. Commercially available tetraethyl orthosilicate, titanium trichloride, and silver-nitrates were used as starting materials. The heat treatment temperature of this coating films was $500^{\circ}C$ properly, obtained from TG-DTA result. The films with thickness of 310 nm were prepared by 5 times coating. In the case of l0 mol% AgO, the film showed a crack-free and smooth surface, but the higher Ago content exhibited the more pin hole and the segregated cluster of AgO. The IR absorbance of the films decreased in the range of 400 nm to 700 nm with the increase of annealing temperature. And the reflectance of the coating films decreased and the color was changed light yellow to white yellow with the increase of Ago content.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.139-146
• /
• 2014

Sodium borohydride ($NaBH_4$) is considered as a secure metal hydride for hydrogen storage and supply. In this study, the interfacial friction of two-phase flow in the dehydrogenation of aqueous $NaBH_4$ solution in a microchannel with a hydraulic diameter of $461{\mu}m$ is investigated for designing a dehydrogenation chemical reactor flow passage. Because hydrogen gas is generated by the hydrolysis of $NaBH_4$ in the presence of a ruthenium catalyst, two different flow phases (aqueous $NaBH_4$ solution and hydrogen gas) exist in the channel. For experimental studies, a microchannel was fabricated on a silicon wafer substrate, and 100-nm ruthenium catalyst was deposited on three sides of the channel surface. A bubbly flow pattern was observed. The experimental results indicate that the two-phase multiplier increases linearly with the void fraction, which depends on the initial concentration, reaction rate, and flow residence time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.116-117
• /
• 2006

We investigated selective emitter effect of Porous Silicon (PSI) as antireflection coatings (ARC). The thin PSi layer, less than 100nm, was electrochemically formed by electrochemical method in about $3{\mu}m$ thick $n^+$ emitter on single crystalline silicon wafer (sc-Si). The appropriate PSi formations for selective emitter effect were carried out a two steps. A first set of samples allowed to be etched after metal-contact processing and a second one to evaporate Ag front-side metallization on PSi layer, by evaluating the I-V features The PSi has reflectance less than 20% in wavelength for 450-1000nm and porosity is about 60%. The cell made after front-contact has improved cell efficiency of about in comparison with the one made after PSi. The observed increase of efficiency for samples with PSi coating could be explained not only by the reduction of the reflection loss and surface recombination but also by the increased short-circuit current (Isc) within selective emitter. The assumption was confirmed by numerical modeling. The obtained results point out that it would be possible to prepare a solar cell over 15% efficiency by the proposed simple technology.

• Transactions of Materials Processing
• /
• v.15 no.1 s.82
• /
• pp.3-8
• /
• 2006

The demand fer small and high-capacity optical data storage devices has rapidly increased. The areal density of optical disk is increased by using higher numerical aperture objective lens and shorter wavelength source. A wafer-scale stacked micro objective lens with a numerical aperture of 0.85 and a focal length of 0.467mm for the 405nm blue- violet laser was designed and fabricated. A diffractive optical element (DOE) was used to compensate the spherical aberration of the objective lens. Among the various fabrication methods for micro DOE, the UV-replication process is more suitable fur mass-production. In this study, an 8-stepped DOE pattern as a master was fabricated by photolithography and reactive ion etching process. A flexible mold was fabricated for improving the releasing properties and shape accuracy in UV-replication process. In the replication process, the effects of exposing time and applied pressure on the replication quality were analyzed. Finally, the surface profiles of master, mold and molded pattern were measured by optical scanning profiler. The geometrical deviation between the master and the molded DOE was less than $0.1{\mu}m$. The diffraction efficiency of the molded DOE was measured by DOE efficiency measurement system which consists of laser source, sample holder, aperture and optical power meter, and the measured value was $84.5\%$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.10
• /
• pp.87-93
• /
• 1994

Ohmic contacts between Au and p-HgHg_{0.7}Cd_{0.3}Te$ with low specific contact resistance have been obtained. The contact region of the wafer is first pre-heated for 5 seconds in a rapid thermal processing equipment. The temperature reaches a maximum value of about 200$^{\circ}C$ at the end of the 5 seconds. Next, a thin Au film is formed on the contact region by immersing the sample in AuCl$_{3}$ solution. the sample is then post-annealed in the same condition as the pre-heating after Pb/In pad metals are deposited on the electroless Au contacts. The specific contact resistance measured by transmission line model is 5${\times}10^{-3}{\Omega}cm^{2}$ at 80K. RBS and differential Hall measurement data suggest that the above low resistance ohmic contact is ascribed to surface traps and increased gold diffusion rate.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.1
• /
• pp.33-40
• /
• 1992

Several etching phenomena were observed and analyzed in diaphragm process performed on 4-inch (100) Si wafers for sensor application. In case of deep etching to above 300$\mu$m depth, the etch-defects appeared at etched surface could be classified into three categories such as hillocks, reaction products, and white residues. It was known that the hillock had a pyramidal shape or trapizoidal hexahedron structure depending on the density and size of the reaction products. The IR spectra showed that the white residue, which was due to the local over-saturation of Si dissolved in solution, was mostly Si-N-O compounds mixed with a small amount of H and C etc. Also, the difference in both the existence of etch-defects and etch rate distribution over a whole wafer was investigated when the etched surfaces were downward, upward horizontally and erective in etching solutions. The obtained data were analyzed through flow pattern in the etching bath. As the results, the downward and erective postures were favorable in the etch rate uniformity and the etch-defect removal, respectively.