• Korean Journal of Materials Research
• /
• v.19 no.1
• /
• pp.33-36
• /
• 2009

Inorganic-organic composite thin-film-transistors (TFTs) of ZnO nanowire/Poly(3-hexylthiophene) (P3HT) were investigated by changing the nanowire densities inside the composites. Crystalline ZnO nanowires were synthesized via an aqueous solution method at a low temperature, and the nanowire densities inside the composites were controlled by changing the ultrasonifiaction time. The channel layers were prepared with composites by spin-coating at 2000 rpm, which was followed by annealing in a vacuum at $100^{\circ}C$ for 10 hours. Au/inorganic-organic composite layer/$SiO_2$ structures were fabricated and the mobility, $I_{on}/I_{off}$ ratio, and threshold voltage were then measured to analyze the electrical characteristics of the channel layer. Compared with a P3HT TFT, the electrical properties of TFT were found to be improved after increasing the nanowire density inside the composites. The mobility of the P3HT TFT was approximately $10^{-4}cm^2/V{\cdot}s$. However, the mobility of the ZnO nanowire/P3HT composite TFT was increased by two orders compared to that of the P3HT TFT. In terms of the $I_{on}/I_{off}$ ratio, the composite device showed a two-fold increase compared to that of the P3HT TFT.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.59-66
• /
• 1997

Di(10-hemisuccinyloxy)decyl muconate(DDM) and di(6-hemisuccinyloxy)hexyl muconate(DHM) were synthesized, and showed a phase transition in an aqueous solution at 97 and $79^{\circ}C$, respectively. They did not form liposomes by themselves or even in the presence of cholesterol or dioleoylphosphatidylethanolamine(DOPE), but did form liposomes when they were mixed with phosphatidylcholine(PC). DHM molecules in liposome membranes were readily polymerized via 1,2-polymerization process on exposure to 254nm. Liposomes composed of DOPE/dioleoylphosphatidylcholine(DOPC)/DHM(3/3/1) were stable at neutral pH, but leaky at weakly acidic pH. The leakage of entrapped calcein from liposomes in phosphate-buffered saline (PBS, $37^{\circ}C$) of pH 4.8 and 5.8 was complete within 30 and 50 min, respectively. The release of toke entrapped calcein was increased with decreasing pH such that 50% and 100% of the calcein were released at pH near 5.5 and 5.0, respectively.

• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.463-469
• /
• 2015

Bisphenol A (BPA) in aqueous solution was measured using HPLC technique, which was established by acetonitrile analysis and KDP solution analysis methods. In these experiments the decomposition characteristics of BPA were compared using the ozone alone, ozone/pH 10, and ozone/hydrogen peroxide processes. About 70% of 10 mg/L of BPA was removed during 60 min by the ozone alone process, while 10 mg/L of BPA was completely removed by the ozone/pH 10 and ozone/hydrogen peroxide processes in 40 min and 60 min, respectively. The final decomposition efficiency drawn from results of TOC and HPLC analyses showed that the ozone/hydrogen peroxide process was the best among them, whereas the concentrations of TOC and reaction intermediates when using the ozone/pH 10 process were higher than those of the ozone alone process after 60 min of reaction. The ozone/hydrogen peroxide process was the most efficient among them when oxidizing organic carbons in water to $CO_2$ and $H_2O$.

• Korean Journal of Food Science and Technology
• /
• v.10 no.2
• /
• pp.209-214
• /
• 1978

Naringinase produced from Aspergillus nidulans was immobilized in acrylamide gel by the entrapping method and its characteristics were studied. Optimum acrylamide concentration was 10%, but N.N'-methylene bisacrylamide concentration had no influence on the final enzyme gel activity. The suitable amount of enzyme dissolved in the polymerization reaction mixture was 126 units/ml. Optimum pH of immobilized enzyme was 5.0 which was the same as that of free enzyme. However, immobilized enzyme showed a higher optumum reaction temperature, markedly increased pH and temperature stability. In a packed-column reactor, the observed reaction rate was increased proportionally to flow rate up to 5ml/min., but independent above 6ml/min.. Activation energy of the immobilized enzyme was 13.01 Kcal/mole, and the energy required for the thermal inactivation was 39.4 Kcal/mole. The apparent Km for 100 mesh gel was $7.23{\times}10^{-3}$ mole.

• Archives of Craniofacial Surgery
• /
• v.25 no.1
• /
• pp.11-16
• /
• 2024

Background: The pathogenesis of orofacial cleft (OFC) is multifactorial, involving both genetic and non-genetic factors, the latter of which play a key role in the development of these anomalies. This paper addresses the incidence of OFC in Indonesia, with a focus on identifying and examining the distribution of contributory factors, including parental medical history, pregnancy history, and environmental influences. Methods: The study was conducted through the collection of primary data. An interdisciplinary research team from Indonesia administered a standardized questionnaire to parents who had children with OFC and who had provided informed consent. The case group comprised 133 children born with cleft lip and/or palate, and the control was 133 noncleft children born full-term. The risk factors associated with OFC anomalies were analyzed using the chi-square test and logistic regression. All statistical analyses were performed using SPSS version 25. A p-value of 0.05 or less was considered to indicate statistical significance. Results: The study comprised 138 children, of whom 82 were boys (59.4%) and 56 were girls (40.6%). Among them, 45 patients (32.6%) presented with both cleft lip and cleft palate, 25 individuals (18.1%) had a cleft palate only, and 28 patients (20.3%) had a cleft lip only. OFC was found to be significantly associated with a maternal family history of congenital birth defects (p<0.05), complications during the first trimester (p<0.05), consumption of local fish (p<0.05), caffeine intake (p<0.05), prolonged medication use (p<0.05), immunization history (p<0.05), passive smoking (p<0.05), and X-ray exposure during pregnancy (p<0.05). Conclusion: The findings indicate close relationships between the incidence of OFC and maternal medical history, prenatal factors, and environmental influences.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.262-266
• /
• 2005

We compared the effects of a representative aliphatic acid amplifier, 4-hydroxy-4'-p-tosyloxy isopropylidene dicyclohexane, doped in poly[tert-butyl methacrylate] (pTBMA), poly[tetrahydropyranyl methacrylate] (pTHPMA) or poly[tert-butoxycarbonyloxystyrene] (pTBOCST) resin film as acid labile polymer in view of thermal stability and photosensitivity enhancement. The acid amplifier was stable up to 20 min in pTBMA and pTBOCST film and up to 5 min in pTHPMA film at $120^{\circ}C$. pTBMA and pTHPMA films doped with the acid amplifier showed four times and two times higher photosensitivity, respectively. But pTBOCST showed negligible photosensitivity enhancement. Photosensitivity enhancement and thermal stability were found to be affected by the resin.

• Geomechanics and Engineering
• /
• v.22 no.4
• /
• pp.329-337
• /
• 2020

Polyacrylamide (PAM) possesses high water absorption capacity and a unique pH-dependent behavior that confer large potential to enhance the engineering performance of clays. In this study, calcium bentonite was treated with a nonionic PAM. Flexible-wall permeability test and the consolidation test were performed at different pH values to evaluate the effects of PAM treatment on the hydraulic and consolidation properties. Test results demonstrate that index properties are affected by the adsorbed PAM on clay surface: a decrease in specific gravity, a decrease in net zeta potential, and an increase in liquid limit are observed due to the PAM treatment. At a given pH, the compressibility of the treated clay is greater than that of the untreated clay. However, the compression indices of untreated and treated clays can be expressed as a single function of the initial void ratio, regardless of pH. Hydraulic conductivity is reduced by PAM treatment about 5 times at both neutral and alkaline pH conditions under similar void ratios, because of the reduction in size of the water flow channel by PAM expansion. However, at acidic pH, the hydraulic conductivity of the treated clay is slightly higher than the untreated clay. This reflects that the treated bentonite with PAM can be beneficially used in barrier system for highly alkaline residues.

• Nuclear Engineering and Technology
• /
• v.56 no.3
• /
• pp.812-818
• /
• 2024

The volume and toxicity of radioactive waste can be decreased by separating the components of high-level liquid waste according to their properties. An impregnated silica-based adsorbent was prepared in this study by combining N,N,N',N',N",N"-hexa-n-octylnitrilotriacetamide (HONTA) extractant, N',N'-di-n-hexyl-thiodiglycolamide (Crea) extractant, and macroporous silica polymer composite particles (SiO₂-P). The performance of platinum-group metals adsorption and separation on prepared (HONTA + Crea)/SiO₂-P adsorbent was then assessed together with that of co-existing metal ions by batch-adsorption and chromatographic separation studies. From the batch-adsorption experiment results, (HONTA + Crea)/SiO₂-P adsorbent showed high adsorption performance of Pd(II) owing to an affinity between Pd(II) and Crea extractant based on the Hard and Soft Acids and Bases theory. Additionally, significant adsorption performance was observed toward Zr(IV) and Mo(VI). Compared with studies using the Crea extractant, the high adsorption performance of Zr(IV) and Mo(VI) is attributed to the HONTA extractant. As revealed from the chromatographic experiment results, most of Pd(II) was recovered from the feed solution using 0.2 M thiourea in 0.1 M HNO₃. Additionally, the possibility of recovery of Zr(IV), Mo(VI), and Re(VII) was observed using the (HONTA + Crea)/SiO₂-P adsorbent.

• Ocean Systems Engineering
• /
• v.8 no.4
• /
• pp.409-426
• /
• 2018

This paper presents the strengthening of tubular joint by wrapping Carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP). In this study, total number of layers, stacking sequence and length of wrapping are the different parameters involved when fiber reinforced polymers (FRP) composites are used for strengthening. For this, parameters where varied and results were compared with the reference joint. The best stacking sequence was identified which has the highest value in ultimate load with lesser deflections. For determining the best stacking sequence, numerical investigation was performed on CFRP composites; length of wrapping and number of layers were fixed. Later, the studies were focused on CFRP and GFRP strengthened joint by varying the total number of layers and length of wrapping. An attempt was done to propose a parametric equation from multiple regression analysis, which can be used for CFRP strengthened joints. Hashin failure criteria was used to check the failure of composites. Results revealed that FRP was having a greater influence in the load bearing capacity of joints, and in reducing the deflections and stresses of joint under axial compressive loads. It was also seen that, CFRP was far better than GFRP in reducing the stresses and deflection.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.153-160
• /
• 2005

There have been large areas of soil contaminated with high levels of explosives. For this experimental work, 2,4,6-trinitrotoluene (TNT) was tested as a representative explosive contaminant of concern in both aqueous and soil samples and its removal was evaluated using three different chemical treatment methods: 1) the classical Fenton reaction which utilizes hydrogen peroxide ($H_2O_2$) and soluble iron at pH less than 3; 2) a modified Fenton reaction which utilizes chelating agents, $H_2O_2$, and soluble iron at pH 7; and 3) a Fenton-like process which utilizes iron minerals instead of soluble iron and $H_2O_2$, generating a hydroxyl radical. Using classic Fenton reaction, 93% of TNT was removed in 20 h at pH 3 (soil spiked with 300 mg/L of TNT, 3% $H_2O_2$ and 1mM Fe(III)), whereas 21% removed at pH 7. The modified Fenton reaction, using nitrilotriacetic acid (NTA), oxalate, ethylenediaminetetraacetic acid (EDTA), acetate and citrate as representative chelating agents, was tested with 3% $H_2O_2$ at pH 7 for 24 h. Results showed the TNT removal in the order of NTA, EDTA, oxalate, citrate and acetate, with the removal efficiency of 87%, 71%, 64%, 46%, and 37%, respectively, suggesting NTA as the most effective chelating agent. The Fenton-like reaction was performed with water contaminated with 100 mg/L TNT and soil contaminated with 300 mg/L TNT, respectively, using 3% $H_2O_2$ and such iron minerals as goethite, magnetite, and hematite. In the goethite-water system, 33% of TNT was removed at pH 3 whereas 28% removed at pH 7. In the magnetite-water system, 40% of TNT was removed at pH 3 whereas 36% removed at pH 7. In the hematite-water system, 40% of TNT was removed at pH 3 whereas 34% removed at pH 7. For further experiments combining the modified Fenton reaction with the Fenton-like reaction, NTA, EDTA, and oxalate were selected with the natural iron minerals, magnetite and hematite at pH 7, based on the results from the modified Fenton reaction. As results, in case magnetite was used, 79%, 59%, and 14% of TNT was removed when NTA, oxalate, and EDTA used, respectively, whereas 73%, 25%, and 19% removed in case of hematite, when NTA, oxalate, and EDTA used, respectively.