DOI QR코드

DOI QR Code

Effect of FRP parameters in strengthening the tubular joint for offshore structures

  • Prashob, P.S. (Department of Mechanical Engineering, Mukesh Patel School of Technology Management and Engineering, NMIMS University) ;
  • Shashikala, A.P. (Department of Civil Engineering, National Institute of Technology Calicut) ;
  • Somasundaran, T.P. (Department of Civil Engineering, Hindustan Institute of Technology and Science)
  • Received : 2018.04.25
  • Accepted : 2018.10.16
  • Published : 2018.12.25

Abstract

This paper presents the strengthening of tubular joint by wrapping Carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP). In this study, total number of layers, stacking sequence and length of wrapping are the different parameters involved when fiber reinforced polymers (FRP) composites are used for strengthening. For this, parameters where varied and results were compared with the reference joint. The best stacking sequence was identified which has the highest value in ultimate load with lesser deflections. For determining the best stacking sequence, numerical investigation was performed on CFRP composites; length of wrapping and number of layers were fixed. Later, the studies were focused on CFRP and GFRP strengthened joint by varying the total number of layers and length of wrapping. An attempt was done to propose a parametric equation from multiple regression analysis, which can be used for CFRP strengthened joints. Hashin failure criteria was used to check the failure of composites. Results revealed that FRP was having a greater influence in the load bearing capacity of joints, and in reducing the deflections and stresses of joint under axial compressive loads. It was also seen that, CFRP was far better than GFRP in reducing the stresses and deflection.

Keywords

References

  1. Agarwal, B.D., Broutman, L.J. and Chandrashekhara, K. (2006), "Analysis and performance of fiber compos-ites", 3rd Ed., Wiley-Interscience Publication, USA.
  2. Al-saidy, A.H., Klaiber, F.W. and Wipf, T.J. (2004), "Repair of steel composite beams with carbon fiber-reinforced polymer plates", J. Compos. Constr., 8(2), 163-172. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:2(163)
  3. Ansys inc. (2009), http://www.ansys.com
  4. Chalmers, D.W. (1991), "Experience in design and production of FRP marine structures", Mar. Struct., 4, 93-115. https://doi.org/10.1016/0951-8339(91)90015-4
  5. Christensen, R.M. (2013), "The theory of materials failure", 1st Ed., Oxford University Press, Great Clarendon Street, Oxford, OX2 6DP, United Kingdom.
  6. Fu, Y., Tong, L., He, L. and Zhao, X.L. (2016), "Experimental and numerical investigation on behavior of CFRP-strengthened circular hollow section gap K-joints", Thin Wall. Struct., 102, 80-97. https://doi.org/10.1016/j.tws.2016.01.020
  7. Ghafoori, E. and Motavalli, M. (2015), "Innovative CFRP-prestressing system for strengthening metallic structures", J. Compos. Constr., 19(6), 1-14
  8. Gholami, M., Mohd Sam, A.R., Marsono, A.K., Tahir, M.M. and Faridmehr, I. (2016), "Performance of steel beams strengthened with pultruded CFRP plate under various exposures", Steel Compos. Struct., 20 (5) 999-1022. https://doi.org/10.12989/SCS.2016.20.5.999
  9. Gkdeniz, N. (2017), "Polymer based composites in marine use: History and future trends", Procedia Eng., 194, 19-24. https://doi.org/10.1016/j.proeng.2017.08.111
  10. Haedir, J. and Zhao, X.L. (2011), "Design of short CFRP-reinforced steel tubular columns", J. Constr. Steel Res., 67 (3)497-509. https://doi.org/10.1016/j.jcsr.2010.09.005
  11. Hashin, Z. (1980), "Failure criteria for unidirectional fibre composites", J. Appl. Mech., 47, 329-334. https://doi.org/10.1115/1.3153664
  12. He, J. and Xian, G. (2016), "Debonding of CFRP-to-steel joints with CFRP delamination", Compos. Struct., 153, 12-20. https://doi.org/10.1016/j.compstruct.2016.05.100
  13. Jones, S.C. and Civjan, S.A. (2003), "Application of fiber reinforced polymer overlays to extend steel fatigue life", J. Compos. Constr., 7, 331-338. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:4(331)
  14. Lesani, M., Bahaari, M..R. and Shokrieh, M.M. (2015), "FRP wrapping for the rehabilitation of Circular Hollow Section (CHS) tubular steel connections", Thin Wall. Struct., 90, 216-234. https://doi.org/10.1016/j.tws.2014.12.013
  15. Lesani, M., Bahaari, M.R. and Shokrieh, M.M. (2013), "Numerical investigation of FRP-strengthened tubular T-joints under axial compressive loads", Compos. Struct., 100, 71-78. https://doi.org/10.1016/j.compstruct.2012.12.020
  16. Lesani, M., Bahaari, M.R. and Shokrieh, M.M. (2014), "Experimental investigation of FRP- strengthened tubular T-joints under axial compressive loads", Constr. Build. Mater., 53, 243-252. https://doi.org/10.1016/j.conbuildmat.2013.11.097
  17. Narmashiri, K. and Mehramiz, G. (2016), "Strengthening of steel hollow pipe sections subjected to transverse loads using CFRP", Mar. Struct., 60 (1) 163-173.
  18. Prashob, P.S., Shashikala, A.P. and Somasundaran, T.P. (2017), "Behaviour of carbon fiber reinforced polymer strengthened tubular joints", Steel Compos. Struct., 24(4) 383-390. https://doi.org/10.12989/SCS.2017.24.4.383
  19. Saiful Islam, A.B.M. (2018), "Dynamic characteristics and fatigue damage prediction of FRP strengthened marine riser", Ocean Syst. Eng., 8(1), 21-32. https://doi.org/10.12989/OSE.2018.8.1.021
  20. Sen, R. (2003), "Advances in the application of FRP for repairing corrosion damage", Prog. Struct. Eng. Mater., 5(2) 99-113. https://doi.org/10.1002/pse.147
  21. Teng, J.G., Yu, T. and Fernando, D. (2012), "Strengthening of steel structures with fiber-reinforced polymer composites", J. Constr. Steel Res., 78, 131-143 https://doi.org/10.1016/j.jcsr.2012.06.011
  22. Zhao, X.L. and Zhang, L. (2007), "State-of-the-art review on FRP strengthened steel structures", Eng. Struct., 29(8), 1808-1823. https://doi.org/10.1016/j.engstruct.2006.10.006