• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1389-1390
• /
• 2007

SF6 gas used widely as insulating component is rising as the environment problem. Electrical breakdown characteristics of epoxy and dry-air composite insulation was investigated on thickness of epoxy and pressure of dry-air under non-uniform field. The gap of needle to plane was from 2mm to 5mm. The pressure of dry-air was varied within the range of $0.1{\sim}0.6$ MPa. The thickness of a needle was 1mm and the curvature radius of a needle end was 100um. The diameter of a plane made of the stainless steel was 50mm. As a result of the experiment, breakdown voltage was increased about 3 times when epoxy was used. The impact that the thickness of epoxy influences on breakdown voltage was poor. It needs suitable thickness computation because the insulating gap of the gas is short as epoxy thickness increases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.5
• /
• pp.413-420
• /
• 2004

In this paper, the control algorithm of DC source device for inverter starting is proposed and the control method for compensating unbalance system source on operating time in the voltage type PWM converter with driving and regenerative faculty is suggested. The maintaining method of balancing condition for converter of AC source is used the compensating unbalanced status by current control loop. In order to solve the problem which the unbalanced system control is used to leakage transformer not equaled reactance by each phase in rectifier system. The proposed H/W and control algorithm of rectifier system is contributed to minimize of device and rising efficiency.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.177-185
• /
• 2000

In this study, the characteristics of various electricity and high resistivity ash collection were measured at superimposed nanosecond pulse energization. The pulse was generated through the hydrogen thyratron. Superimposed pulse was nanosecond duration pulse that had fast pulse rising time 100[ns], short pulse width 500∼850[ns] and pulse fall time 400∼750[ns]. The results of this study are summarized as followings; Frist, compared with the DC ESP(electrostatic precipitator), superimposed pulse ESP could induce higher peak voltage, and had the about 30[%] reduction of ESP collection area and 50∼80[%] reduction of power consumption. showing the same efficiency. Second, enhancement factor H had 1.9∼3.6 with the increase of migration velocity.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1667-1669
• /
• 2004

In this paper, the elastic epoxy added elastomer having viscoelasticity to existing epoxy was measured thermal, structural properties by DSC (Differential Scanning Calorimetry) and FESEM (Field Emission Scanning Electron Microscope). Specimens were made of dumbbell forms by the ratio of 5, 10, 15, and 20[phr] by regulation with elastomer contents. The measurement temperature dimensions of DSC were -20[$^{\circ}C$] to 150[$^{\circ}C$] and rising temperature was 4[$^{\circ}C$/min]. Also we observed structure through FESEM at the magnification of 1000 times with the voltage of 15[kV] after breaking by quenching specimens. As experimental results, we could know that thermal and structural properties were improved quantity according to decrease of elastomer contents. Namely, it increased glass transition temperature, high temperature, and matrix structure. In general, thermal, structural properties of 15[phr] was excellent among the specimens.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2835-2838
• /
• 2003

We study the characteristics of oscillating in non-autonomous condition and the conducted noise generation in a RL-photocoupler circuit. This circuit may be shown a period-doubling and a chaos dynamics under any specific conditions of input circuit. But, the relationship between input signals and output signals is different according to the amplitude of driving input voltage. Then, the oscillation noise was analyzed with respect to both the frequency and the amplitude of an external ac signal and do values. The results show that the noise-induced oscillations for falling and rising cycles induced by kick-back effect in an inductor, nonlinear capacitance, nonlinear resistance and charge storage time in a diode and an LED. We also compared the simulation with the experimental results.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.973-975
• /
• 1992

The Acoustic Emission due to treeing progress in Crosslinked Polyethylene(XLPE) is studied by using the self developed automatic measuring system of acoustic emission. Tree progression and average pulse amplitude are almost in proportion to the rising of applied voltage but there is no proportionality relation between tree progression and pulse numbers. From now on, Skewness and kurtosis of average cycle, special property of $\phi$-a distribution characteristics can be confirmed as the useful parameters of treeing deterioration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.207-210
• /
• 2001

Electrical equipment for railway is always experiencing wear and degradation by mechanical, electrical and environmental stress in service and the fault or the accident of high voltage main circuit directly causes operation interruption. Particularly propulsion drive of high speed switching inverter takes the form of specific degradation mechanism such as fast rising transient surge, reflective overvoltage and harmonic stress, and it is known that it threatens the long life and the reliability of electrical equipment. In this paper, statistics of fault and accident on main electrical equipment for railway are presented and also insulation degradation mechanism, which governs end life of electrical device, is analyzed. Finally the method of fault respondence and reliability improvement on the main electrical equipments will be reviewed in order to prevent operation interruption.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.197-200
• /
• 2008

We propose a novel n-type a-Si:H TFT pixel circuit which is proper to AMOLED display for the large size and high resolution. Proposed pixel circuit will be suit to panel for the high resolution because of different threshold sampling method. Driving method of proposed pixel circuit is very simple like an AMLCD. Our simulation indicates that the proposed pixel circuit can compensate the Vth shift and IR rising of power line so that provide better quality image.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.157-161
• /
• 2000

The electronic ballasts for low pressure discharge lamps are produced and commercialized. However, the electronic ballasts for high pressure lamps are now in progress because of poor reliability and high cost. The major case of troubles with electronic ballasts are thermal destruction of semiconductor output switches due to non ideal i-v characteristics of switch. The loss converts to heat and rises the temperature of switch and it increases proportionally to switching frequency and value of current and voltage. This study shows the variable frequency ballasts which can suppress the heating of switches efficiently. It is used for the limitation the switch current and the rising temperature of switch by impedance variation of lamp inductor. As a result, initial warm-up time of the proposed ballasts was faster than that of magnetic ballasts about 90 msec. Power factor of tested ballasts follow as ; input and output average of magnetic ballasts are 93 [%] and 86 [%], respectively, And proposed ballasts are 97 [%] and 99 [%], respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.360-365
• /
• 2009

On this paper, piezoelectric generators using piezoelectric ceramics were designed and fabricated. Generators were made by attaching cymbal type metal plates on upper and bottom sides of a disc type piezoelectric ceramic. Generator converts wasting mechanical energy to electrical energy. Output voltage was increased when thickness of ceramic and displacement of vibration were increased. Temperature of the ceramic was increased when it generates, but the temperature rising was saturated at certain temperature.