• 전기학회논문지
• /
• 제67권3호
• /
• pp.413-418
• /
• 2018

In this paper, we describe the development of a non-enzymatic glucose sensor based on copper nanocubes(Cu NCs) electroplated laser induced graphene(LIG) electrodes which can detect a certain range of glucose concentrations. $CO_2$ laser equipment was used to form LIG electrodes on the PI film. This fabrication method allows easy control of the LIG electrode size and shape. The Cu NCs were electrochemically deposited on the LIG electrodes to improve electron transfer rates and thus enhancing electrocatalytic reaction with glucose. The average sheet resistances before and after electroplating were $15.6{\Omega}/{\Box}$ and $19.6{\Omega}/{\Box}$, respectively, which confirmed that copper nanocubes were formed on the laser induced graphene electrodes. The prepared electrode was used to measure the current according to glucose concentration using an electrochemical method. The LIG electrodes with Cu NCs demonstrated a high degree of sensitivity ($1643.31{\mu}A/mM{\cdot}cm^2$), good stability with a linear response to glucose ranging from 0.05 mM to 1 mM concentration, and a limit of detection of 0.05 mM. In order to verify that these electrodes can be used as flexible devices, the electrodes were bent to $30^{\circ}$, $90^{\circ}$, and $180^{\circ}$ and cyclic voltammetry measurements were taken while the electrodes were bent. The measured data showed that the peak voltage was almost constant at 0.42 V and the signal was stable even in the flexed condition. Therefore, it is concluded that these electrodes can be used in flexible sensors for detecting glucose in the physiological sample like saliva, tear or sweat.

• 전력전자학회논문지
• /
• 제4권5호
• /
• pp.462-473
• /
• 1999

디지털 제어 방식으로 구동되는 모든 교류 전동기 벡터제어시스템의 근간을 이루는 전류 측정에 관한 문제를 다룬다. 일반적인 펄스폭 변조 방식 교류 전동기 구동 시스템에서 전동기 전류에 포함된 인버터 스위칭 노이즈를 없애기 위하여 저역 통과 필터를 사용하는데 이러한 필터는 필연적으로 측정된 신호의 시간 지연을 유발하게 된다. 따라서 샘플링한 전류값에는 기본파 성분 뿐만아니라 고조파 리플 성분이 포함된다. 본 논문에서는 3상 대칭 펄스폭 변조시 기준 전압 벡터의 위치에 다른 전류 샘플링 오차를 해석적으로 구하고 이러한 샘플링 오차를 최소화하기 위한 기법을 제안한다. 제안된 지연 보상 샘플링 기법을 사용하면 정상 상태 전류 측정 오차를 최소화할 수 있고 보다 정확한 토오크 제어가 가능하게 됨을 시뮬레이션과 실험을 통해 보였다.

• 대한전자공학회논문지
• /
• 제18권4호
• /
• pp.49-61
• /
• 1981

N+P, N+PP+ 형 태양전지를 제조하여 얻은 실험자료들을 근거로 실리콘 접합형 태양전지에 일반적으로 적용할 수 있는 컴퓨터 모의 실험 프로그램을 개발하고, 이의 유용성을 확인하였다. 이 모의 실험 프로그램은 N+P, P+N, N+PP+, P+NN+형의 실리콘 태양전지에 적용할 수 있는 것으로, 입사광은 AMI, 등강도 광원, 인공조명으로 많이 사용되는 GE -ELH 광원이고, AR코팅은 Si3N4형과 투과도가 파장에 관계없는 일정형 2종류가 있으며, 프로그램에서 이들 전지의 구조, 광원, AR 코팅 종류에 대한 파장 특성분포도 쉽게 변화시킬 수 있도록 되어 있다. 이 모의실험의 결과들을 토대로 N+와 P 영역에서의 평균도오핑농도와 전지의 두께, AMI 스펙트럼에 대한 집광도, 앞면 접합깊이에 대하여 효율이 최대가 되는 최적치들을 구하였으며, 앞면의 표면 재결합 속도, 접합부에서의 캐리어의 유효 수명, 누설저항에 대하여는 허용 한계치로, 기타 효율변화인자로서 동작온도 직렬저항과 전기장의 세기에 대하여는 효율의 변화율로서 파라미터들이 효율에 미치는 영향들을 분석하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권5호
• /
• pp.700-706
• /
• 2012

이동식발전설비에서 시동장치의 핵심기술은 피니언기어 쉬프팅 장치와 초기 기동전압을 제한하는 것이며 기존의 제품에서는 기계적 주접점을 이용한 시동 제어장치를 사용하고 있다. 하지만 완전한 피니언기어 쉬프팅 후 시동전동기의 기동의 불확실성이나 대전류에 의한 주접점의 아크손상 등의 큰 문제점을 가지고 있다. 본 연구에서는 이러한 문제점을 해결하기 위해 기동의 불확실성 제거를 위한 피니언기어 쉬프팅 제어회로, 대전류에 의한 접점의 아크손상 방지를 위해 반도체 소자를 이용한 시동 제어시스템, 직권전동기의 소프트 스타팅을 위한 기동 안전장치 등을 새롭게 설계, 제작하여 안전성과 신뢰성을 얻고자 하였다. 또한, 피니언기어 제어회로와 전동기 전원회로를 분리하여 전기적 안전성을 확보하였다.

• 전력전자학회논문지
• /
• 제16권2호
• /
• pp.152-161
• /
• 2011

영구자석 매립형 동기전동기는 고효율, 소형화 및 넓은 가변속운전 등의 특성으로 인해 전기자동차에 적용되고 있다. 본 논문에서는 유기전압이 고조파를 함유하고 있는 영구자석 동기전동기에 대하여 고속운전 시 약자속 운전 영역의 해석에 대해 제안한다. 유기전압의 고조파가 전동기 속도와 최대토크에 미치는 영향을 해석하고 전압제한 및 전류제한 조건에서 최대토크 운전을 위한 dq 전류에 대해 분석한다. 약자속 운전영역에 대한 기존 및 제안된 해석결과를 비교하고 최대토크-속도 특성의 실험을 통하여 해석결과를 검증한다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.353-356
• /
• 2009

A pivotal mechanical balance of plant for 75kW class molten carbonate fuel cells comprise of a catalytic burner and an ejector which has been designed and tested in KEPRI(Korea Electric Power Research Institute). The catalytic burner, which oxidizes residual fuel in the anode tail gas, was operated at several conditions. Some problems arose due to local overheating or auto-ignition, which could limit the catalyst life. The catalytic burner was designed by considering both gas mixing and gas velocity. Test results showed that the temperature distribution is very uniform. In addition, an ejector is a fluid machinery to be utilized for mixing fluids, maintaining vacuum, and transporting them. The ejector is placed at mixing point between the anode off gas and the cathode off gas or the fresh air Several ejectors were designed and tested to form a suction on the fuel tail gas and balance the differential pressures between anode and cathode over a range of operating conditions. The tests showed that the design of the nozzle and throat played an important role in balancing the anode tail and cathode inlet gas pressures. The 75kW MCFC system built in our ejector and catalytic burner was successfully operated from Novembe, 2008 to April, 2009. It recorded the voltage of 104V at the current of 754A and reached the maximum generating power of 78.5kW DC. The results for both stand-alone and integration into another balance of plant are discussed.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권1호
• /
• pp.1-7
• /
• 2000

The SNOSFET memory devices with ultrathin ONO(tunnel oxide-nitride-blocking oxide) gate dielectric were fabricated using n-well CMOS process and investigated its characteristics. The thicknesses of tunnel oxide, nitride and blocking oxide were $23{\AA},\; 53{\AA}\; and\; 33{\AA}$, respectively. Auger analysis shows that the ONO layer is made up of $SiO_2(upper layer of blocking oxide)/O-rich\; SiO_x\N\_y$. It clearly shows that the converting layer with $SiO_x\N\_y(lower layer of blocking oxide)/N-rich SiO_x\N\_y(nitride)/O-rich SiO_x\N\_y(tunnel oxide)$. It clearly shows that the converting layer with $SiO_x\N\_y$ phase exists near the interface between the blocking oxide and nitride. The programming condition of +8 V, 20 ms, -8 V, 50 ms is determined and data retention over 10 years is obtained. Under the condition of 8 V programming, it was confirmed that the modified Fowler-Nordheim tunneling id dominant charge transport mechanism. The programmed threshold voltage is distributed less than 0.1 V so that the reading error of memory stated can be minimized. An $8\times8$ NAND type flash EEPROM with SONOSFET memory cell was designed and simulated with the extracted SPICE parameters. The sufficient read cell current was obtained and the upper limit of $V_{TH}$ for write state was over 2V.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.424-424
• /
• 2008

Dye-sensitized Solar Cell (DSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The electric potential distribution in DSCs has played a major role in the operation of such cells. Models based on a built-in electric field which sets the upper limit for the open circuit voltage(Voc) and/or the possibility of a Schottky barrier at the interface between the mesoporous wide band gap semiconductor and the transparent conducting substrate have been presented. $TiO_2$ thin films were deposited on the FTO substrate by Nd:YAG Pulsed Laser Deposition(PLD) at room temperature and post-deposition annealing at $500^{\circ}C$ in flowing $O_2$ atmosphere for 1 hour. The structural properties of $TiO_2$ thin films have investigated by X-ray diffraction(XRD) and atomic force microscope(AFM). Thickness of $TiO_2$ thin films were controlled deference deposition time and measurement by scanning electron microscope(SEM). Then we manufactured a DSC unit cells and I-V and efficiency were tested using solar simulator.

• 한국철도학회논문집
• /
• 제9권6호
• /
• pp.761-765
• /
• 2006

At present, harmonic currents cause serious problems in power conversion system using the semiconductor switching device. Also some of the conversion system provokes harmonic currents against to the main power supply system and causes hindrances for the system. Main power impedance of the traditional LC passive filter method, influences on the filter characteristics and amplifies the harmonics when resonance phenomenon is occurred. And the traditional existing 2 level inverter systems show the limit in capacity of voltage and current in case of occurring sudden load change. So, to solve this problem active filter which uses cascaded H-bridge multi level inverter has been designed and ex-filter system circuits were totally investigated. With multi level active filtering system not only the size of filter but also the size of filter for transformer can be reduced by half and so as to the weight, while the capacity of inverter can be double sized and wave forms can be compensated exactly and precisely. Also by the benefit of the increase in rating capacity, the various currents owing to the load fluctuation can be dealt more steadily. In order to simulate the wave form of harmonics based on the measured data on the AC 25kV high speed Domestic Commercial railway, it was simulated with PSCAD/EMTDC and PSIM. Based on the results of this demonstration, the power supply system and inverter system would be more stable and also promoting its efficiency.

• 센서학회지
• /
• 제29권1호
• /
• pp.7-13
• /
• 2020

Dielectric capacitors are integral components in electronic devices that protect the electric circuit by providing modulated steady voltage. Explosive growth of the electric automobile market has resulted in an increasing demand for dielectric capacitors that can operate at temperatures as high as 400 ℃. To surpass the operation temperature limit of currently available commercial capacitors that operate in temperatures up to 125 ℃, Bi_1/2Na_1/2TiO₃ (BNT), which has a large temperature-insensitive dielectric response with a maximum dielectric permittivity temperature of 300 ℃, was selected. By introducing an intentional A-site cation deficiency and post-heat treatment, we successfully manage to control the dielectric properties of BNT to use it for high-temperature applications. The key feature of this new BNT is remarkable reduction in dielectric loss (0.36 to 0.018) at high temperature (300 ℃). Structural, dielectric, and electrical properties of this newly developed BNT were systematically investigated to understand the underlying mechanism.