• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.75-80
• /
• 1998

Statistical Energy Analysis(SEA) has been considered as a possible method for predicting responses of complex structures, especially at higher frequencies. In this paper, an SEA model of vehicle was built using 138 energy storing subsystems connected together using 1019 junctions. SEAM software program was used to build and calculate the model. To demonstrate the accuracy of the SEA model, predicted response levels were compared with measured levels. The source input levels were measured at the engine mounting parts. For the vibration levels, the agreement between the calculation results and the experimental ones was found to be good. The energy flow between connected subsystems can be presented, because the analysis method is based on the estimation of the power flow between subsystems. This paper also identifies some dominant energy flow paths from sources. It is finally presented that the SEA model can optimize the design parameters of vehicles using model parameters and energy flow paths.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.99-101
• /
• 2005

This paper is concerned with the active vibration control of flexible plate system using $H_2$ controller. The main objective of this paper is to propose the system identification for estimation dynamic equation of plate vibration system and control algorithm such as $H_2$ controller design. In this paper dynamic equation is determined by considering only the first, second, and third vibration modes, and experiments confirm that this model works well. The $H_2$ control algorithm is proposed and implemented on the experimental setup to show their efficacy. Effectiveness and performance of the designed controller was verified by both simulation and experiment result.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.57-64
• /
• 1999

In order to decide critical vibration level on structural damages induced by near blasting, deformation of existing cracks in structure was investigated and ground vibrations were measured. New criteria to evaluate blasting damage to structure are proposed considering daily deformation of cracks in structures. Results from 2 brick houses in fishing village show that new design criteria far more than current are required to cause structural damage for brick houses.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1580-1588
• /
• 1997

A modeling method for the flapwise bending vibration of a rotating cantilever beam which has small slenderness ratio is presented in this paper. It is shown that as the slenderness ratio decreases the shear and rotary inertia effects increase. Such effects become critical for the accurate estimation of the natural frequencies and modeshapes, especially higher frequencies and modes, as the angular speed increases. It is also shown that the flapwise bending natural frequencies are higher than the chordwise bending natural frequencies. The discrepancy between first natural frequencies are especially significant when the hub radius ratio is small.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.390.1-390
• /
• 2002

In this study, we investigate the plugging effect on the CE type steam generator tube. The natural frequency and mode shape will be changed due to decrease of the effective mass distribution along the tube. We compared the variation of stability ratio for plugged tube with that fur unplugged one. The natural frequency increased because of removing the cooling water inside the steam generator tube, but the stability ratio decreased inversely because of changing the vibrational mode shape. We also investigated the turbulent excitation effect.

• Smart Structures and Systems
• /
• v.11 no.6
• /
• pp.569-587
• /
• 2013

This paper evaluates the closed loop performance of the reaching law based discrete sliding mode controller with multisensor data fusion (MSDF) in real time, by controlling the first two vibrating modes of a piezo actuated structure. The vibration is measured using two homogeneous piezo sensors. The states estimated from sensors output are fused. Four fusion algorithms are considered, whose output is used to control the structural vibration. The controller is designed using a model identified through linear Recursive Least Square (RLS) method, based on ARX model. Improved vibration suppression is achieved with fused data as compared to single sensor. The experimental evaluation of the closed loop performance of sliding mode controller with data fusion applied to piezo actuated structure is the contribution in this work.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.9
• /
• pp.856-860
• /
• 2007

This paper presents a robust tracking controller design method for the track-following system of an optical recording device. A tracking loop gain adjustment algorithm is introduced to accurately estimate the tracking vibration quantity in spite of the uncertainties of the tracking actuator. A minimum tracking open-loop gain is calculated by the estimated tracking vibration quantity and a tolerable limit of tracking error. A robust tracking controller is designed by considering a robust $H_\infty$ control problem with the weighting function of a slightly larger gain than the minimum tracking open-loop gain. The proposed controller design method is applied to the track-following system of an optical recording device and is evaluated through the experimental result.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.690-699
• /
• 1998

This paper discusses the techniques, procedures and the results of the ground vibration test(GVT) performed on the development aircraft and the simple procedure of FE model updating technique from the GVT results. The GVT was carried out using random excitation technique with MIMO(Multi-Input-Multi-Output) data acquistion method, and taking full advantage of poly-reference global parameter estimation technique to identify the vibration modes. In dynamic FE modeling, the aircraft was represented by beam elements and all dynamic analysis was performed using MSC/NASTRAN for this model. In updating procedure, the stiffness of the beam model was adjusted iteratively so as to get the natural frequencies and mode shapes close to the GVT results.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.3
• /
• pp.73-81
• /
• 1991

There have been many studies on chatter vibration in machining but there seems to be no regulations to decide the commencing point of chatter objectively. The development of an objective method which can estimate and detect chatter commencement is very much in need for automatic manufacturing systems, dynamic performance tests for machine tools, so on. In this study, therefore, the estimation and the in-process detection of chatter have been experi- mentally investigated for the turning process. As a result, the commencing point of chatter can be decided from the behavior of the maximum amplitude of the dynamic component of cutting force, where the maximum amplitude is suddenly increasing with the chatter commencement. Then the commencing point of chatter can be estimated practically by this method before the occurrence of excessive vibration. Also, it is possible to detect the occurence of chatter vibration through the in-process measurement, by monitoring the maximum amplitude of the dynamic component of cutting force.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.404-409
• /
• 2011

Report on the notion of uncertainty is important. The reason is that the measured value includes a lot of uncertain factors. Reliable results can't be derived without the notion of uncertainty. The mathematical model to evaluate uncertainty considering the quality of vibration is important to evaluate uncertainty, and it must contain the every quantity which contributes significantly to uncertainty in the measured results. In this paper, the evaluation of uncertainty analysis about rotor vibration measurements of machine tools is presented to evaluate the most important factors of uncertainty.