• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.398-403
• /
• 2004

The demand of high speed machining is increasing because the high speed cutting providers high efficiency of process, short process time, improved metal removal capacity and better surface finish. Active magnetic bearings allow much high surface speed than conventional ball bearings and therefore greatly suitable for high speed cutting. The automatic control concept of magnetic bearing system provides ability of intelligent control of spindle system to increase accuracy and flexibility by means of adaptive vibration control. This paper describes a design and development of a milling spindle system which includes built-in motor with power 5.5㎾ and maximum speed 70,000rpm, HSK-32C tool holer and active magnetic bearing system. Magnetic actuators are designed for satisfying static load condition. The Performances of manufactured spindle system was examined for its static and dynamic stiffness, load capacity, and rotational accuracy. This spindle was run up to 70,000 rpm stably, which is 3.5 million DmN.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.1
• /
• pp.78-84
• /
• 2011

Using sensors to detect current or voltage of motors is disadvantaged because motor is exposed to vibration, impacts, corrosion, high temperature and humidity in the machinery structure like HEV. In the case of IPMSM, position information is included not only in the flux or EMF term but also in the rotator inductance because of its saliency. To solve this problem, a new mathematical model of IPMSMs on fixed frame is proposed and an extended EMF includiing rotating position information is defined to estimate extended EMF. A strong low-pass filter through the variable cut-off frequency using velocity function was proposed. This makes it is possible to estimate extended EMF by least order disturbance observer. The proposed method was proved through the experiment.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11b
• /
• pp.832-834
• /
• 2010

본 논문에서는 권선형 엘리베이터 시스템의 종방향의 운동을 표현할 수 있는 운동방정식을 도출한다. 기존의 권선형 엘리베이터 시스템의 종진동을 억제하기 위하여 MR유체를 특징으로 하는 댐퍼를 적용하고, MR댐퍼가 적용된 시스템의 운동방정식을 도출한다. 부하하는 자기장에 따른 엘리베이터 시스템의 종진동 저감의 변화를 관찰하였다.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.131-134
• /
• 2014

PMSM(Permanent Magnet Synchronous Motor)은 가공기, 로봇, 공장 자동화 등 현재까지도 산업 시스템 전반에 널리 쓰이고 있으며, 그에 대한 연구도 활발히 진행되고 있다. 하지만 PMSM에 부하를 인가하거나 혹은 기계 몸체와의 결합 과정에서 기구부가 가지고 있는 고유진동 주파수에 의해 동력 전달 부분에 있어 기계계의 응답 특성은 불안정해지고, 떨림 현상이 발생된다. 본 논문에서는 PMSM을 이용한 회전 운동 시스템에서 출력되는 전류에 기구부가 가지고 있는 특정 영역의 고유진동 주파수를 제거한 전류를 적응 노치필터를 통해 내보낸다. 그 결과 기계부의 떨림 현상을 제거하고, 안정적인 제어 시스템을 제안한다. 이 제어알고리즘을 가상실험으로 필터 통과 전과 후의 결과를 비교 및 분석하도록 한다.

• Journal of KSNVE
• /
• v.6 no.6
• /
• pp.851-856
• /
• 1996

The active noise cancellation system showing the effective convergence and stability has been studied by simplifying the controller structures using the weighting factors of control error path to the multi-channel filtered-x LMS algorithm which needs a lot of calculations and the performance has been verified experimentally. Besides, to implement the system performance in a vehicle cabin, experimental work for selecting the suitable numbers and positions of the microphones and speakers was accomplished. Effectively combining a TMS 320C 31 main processor conducting real number calculations and having various functions with other components, the purpose-built system board for active noise cancellation has been designed and with this board, car active noise cancellation system showing maximum stable 10dB noise reduction has been obtained at the car idling conditions above 3000rpm range.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.09a
• /
• pp.357-363
• /
• 2002

본 연구에서는 지진하중을 받는 구조물의 MR감쇠기를 이용한 모드제어를 구현하고자 한다. 모드제어는 저차의 모드만을 이용하여 구조물의 진동을 제어한다. 따라서 토목구조물과 같은 자유도가 많은 대형구조물의 제어에 적합하며, 제어기의 설계 역시 다른 제어이론에 비해 간편하다. 모드제어에 대한 앞선 연구들이 많이 있음에도 불구하고, 반능동제어, 특히 MR감쇠기에 대한 모드제어의 성능에 대한 연구가 없었다. 본 연구에서는 MR댐퍼에 대한 효율성을 검토하기 위해서, 모드제어이론을 지진하중을 받는 구조물에 구현하였다. 센서로부터 측정된 응답을 이용하여 모드응답을 예측하기 위해 칼만필터를 구현하였으며, Spillover problem을 해결하기 위해 low-pass filter가 적용되었다. 수치예제를 통해 저차의 모드만을 제어함으로써, 구조물의 거동이 효과적으로 줄어드는 것을 확인하였다. 그러나 줄어드는 정도는 제어기의 가중치행렬과 칼만필터에 사용되는 센서에 의해 측정된 응답에 따라 다르다

• Proceedings of the KSR Conference
• /
• 2003.10a
• /
• pp.210-215
• /
• 2003

Korean High Speed Train (KHST) has been tested on high speed line in JungBu site since it was developed in 2002. The KHST figured 7 cars was modeled for dynamic simulation with Vampire program. and the data acquisition system was used to test successfully the on-line test for proving the dynamic performance of KHST. The comparison between test and simulation results for dynamic behavior of KHST was tried in this paper and it was very difficult because the environmental conditions and running conditions have an effect on the test results and these conditions are unable to be modeled for dynamic analysis. Also the parameters for data acquisition system for test are usually not same to simulation conditions. Therefor, in this paper the acceleration data after filtering with low pass filter below 1Hz were used to compare between test and simulation results because the low frequency range is useful to evaluate the dynamic performance for railway vehicle system, so as steady state curving acceleration. The results show that both are similar in low frequency range.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.357-363
• /
• 2005

The non-minimum phase characteristic of a flexible manipulator makes tracking control of its tip difficult. The level of the tip tracking performance of a flexible manipulator is significantly affected by the characteristics of the tip reference trajectory as well as the characteristics of the flexible manipulator system. This paper addresses the question of how to best specify a reference trajectory for the tip of a flexible manipulator to follow in order to achieve the objectives of reducing : tip tracking error, residual tip vibration, and the required actuation effort at the manipulator joint. A novel method of tip-based learning controller for the flexible manipulator system is proposed in the paper, where a model of the flexible manipulator system with a command shaping filter is used to generate a smooth and realizable tip reference trajectory for a tip-based learning controller.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.287-292
• /
• 1998

This paper presents some results of performance evaluation test via actual machines of a new hybrid vector control utilizing a new indirect orientation scheme and stable filter embedded direct orientation scheme for induction motors without speed or position sensor. It is shown through the test by 0.3(kW) and 3.7(kW) motors that the proposed sensorless vector control has the following high potentialities: 1) speed range is 0 to 600(rad/s) or more, 2) zero-speed command is accepted and settles the machines at a stable standstill with no vibration 3) it can make machines to track variable command of acceleration and deceleration $\pm$6,000(rad/s2), 4) it can make machines to drive directly load of at least 26 times larger inertia than that of the machine, 5) it can make machines to produce much larger torque than the rating in torque control mode even at standstill. The performance confirmed by the test is far away for previous schemes or sensorless drive apparatuses.

• Journal of KSNVE
• /
• v.3 no.4
• /
• pp.383-394
• /
• 1993

An automotive suspension system generally behaves like a low frequency band-pass filter(0.5 - 10 Hz). Passengers are very sensitive to this frequency range in terms of ride quality and road holding ability. In this paper, a LQG/ LTR controller is suggested to improve the ride quality and road holding ability in the specified frequency rage. It has been found by numerical simulation that the ride quality and road holding ability can be improved in the frequency ranges of 0.5 - 3.0 Hz and 0.3 - 2.1 Hz respectively. In addition, a new approach using root locus to evaluate the stability robustness of the active suspension system is studied. It is shown that the stability robustness of the LQG/LTR controller designed in this paper is improved, compared to the passive system.