• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.120-123
• /
• 2004

The bending phenomenon has been known to be occurred by the difference of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets inside die chamber after passing the multi-hole container. The curvature can be controlled by the two variables, the one of them is the different velocity of billets through the multi-hole container, the other is the difference of hole diameter. The bending phenomenon during extruding using four billets can be obtained by the difference of hole diameters in the multi-hole container or by the difference of relative velocity of billet inserted in the container. As results of DEFORM-3D analysis, it can be shown that bending can be obtained during extruding by the difference of relative velocity of two billets or by the difference of hole diameter, and the amount of curvature is increased by the difference of velocity and diameter. According to the shape of products, the curvature of rectangular section is bigger than the curvature of regular square section. And, it is estimated that, because the stress on the welding line is much higher than yield stress of material, the bonding of four billets can be obtained.

• 대한물리의학회지
• /
• 제5권4호
• /
• pp.577-585
• /
• 2010

Purpose : This study was to evaluate gait velocity and stance time on 5 conditions in elderly women and elderly women with LBP. The subjects were 70's generation. Methods : The subjects are 20 divided into 2 groups. They measured gait velocity, stance-time. The 5 conditions were normal gait, 10cm obstacle gait, 25cm obstacle gait, dual 10cm obstacle gait, dual 25cm obstacle gait. The experimental period was between 2008/12 and 2009/2. Statistical analysis was used Repeated measurement for difference between conditions, independent t-test for difference in two groups. Subjects were countdown from 50 during dual task gait. Results : The results were as follow: there were significantly difference 10cm obstacle velocity, dual 10cm obstacle velocity in two group. The others were not significantly differences. Velocity and stance-time were significantly difference in control group. In dual 25cm obstacle gait, velocity was difference of normal gait. Stance-time was difference in 25cm obstacle gait, and dual 25cm obstacle gait. In Experimental group, velocity and stance-time were not significantly difference. But measured value of velocity was gradually decreased and stance time was increased. Conclusion : These results indicate that elderly people with LBP women are reduced gait ability in dual task, and obstacle condition. So they need to prevent falling in dual task, and obstacle gait and to train obstacle/dual tak gait.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.719-722
• /
• 2002

Cylindrical cam mechanisms are used commonly in many automatic machinery. But the cylindrical cam is very difficult to design and manufacture the shape. The motion analysis of the cylindrical cam can check the accuracy between designed data and manufactured data of the cam shape and can reproduce without the cam design data. The motion analysis of the cylindrical cam consists of displacement analysis, velocity analysis and acceleration analysis. This paper performs the motion analysis of a cylindrical cam with translating follower by using a relative velocity method and a central difference method. The displacement is calculated by using the central difference method and the velocity is calculated by the relative velocity method. The relative velocity method is defined by the relative motion between follower and cam at a center of a follower roller. The central difference method is derived in the 3 dimensional space.

• 한국연소학회지
• /
• 제2권1호
• /
• pp.9-16
• /
• 1997

This paper investigates the linear stability of wakes with special emphasis on the difference of velocity and density. Velocity and density profiles for laminar flows have gaussian profiles. Incompressible wakes have two generalized inflection points and two unstable modes-sinuous and varicose modes. Sinuous modes are more unstable than varicose modes irrespective of density variation, which shows wakes will be destabilized by sinuous modes. Large velocity difference and density difference leads to more unstable wakes due to large momentum difference.

• 대한기계학회논문집B
• /
• 제27권10호
• /
• pp.1450-1456
• /
• 2003

Three-dimensional pipe flows with elbows, tees and headers in three different pipe systems are calculated to estimate the effect of asymmetry of axial velocity profile and swirl on measuring accuracy of an orifice flowmeter. It is evaluated how the pressure difference across the orifice is dependent on the upstream straight pipe length and how swirl intensity, swirl angle, and axial velocity distribution affect the measuring error of the orifice flowmeter. From the results, it is found that variation of the pressure difference across the orifice is negligible in case that maximum swirl angle is less than 2$^{\circ}$, and also that the pressure difference across the orifice is more sensitive to the asymmetry of axial velocity profile rather than the swirl intensity.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2007년도 Proceedings of ISRS 2007
• /
• pp.625-628
• /
• 2007

We present an efficient and robust technique to estimate the velocity of moving targets from a single SAR image. In SAR images, azimuth image shift is a well known phenomenon, which is observed in moving targets having slant-range velocity. Most methods estimated the velocity of moving targets from the distance difference between the road and moving targets or between ship and the ship wake. However, the methods could not be always applied to moving targets because it is difficult to find the road and the ship wake. We adopted a method estimating the velocity of moving targets from azimuth differentials of range-compressed image. This method is based on an assumption that Doppler center frequency shift of moving target causes a phase difference in azimuth differential values. The phase difference is linearly distorted by Doppler rate due to the geometry of SAR image. The linear distortion is eliminated from phase removal procedure, and the constant phase difference is estimated. Finally, range velocity estimates for moving targets are retrieved. This technique is tested using an ENVISAT ASAR image in which several unknown ships are presented. The theoretical accuracy of this technique is discussed by SAR simulation. The advantages and disadvantages of this method over the conventional method are also discussed.

• 혜화의학회지
• /
• 제11권1호
• /
• pp.1-9
• /
• 2002

1. Purpose We inquire into difference of blood flow velocity according Sasang Constitution. 2. Method We selected observation group that they are 251 patients among of the patients who are had a medical early examination of stroke. We classified observation group by Sasang Constitution and compared each of measured blood flow velocity by TCD. 3. Result 1) We found out that Taeumin is highest in fat rate, height and blood pressure. 2) Blood flow mean velocity of MCA is not found out significant difference by Sasang Constitution. But, Taeumin is found out highest in left and right. 3) Taeumin is found out that blood flow velocity of Siphon sinus ICA is highest.

• 화약ㆍ발파
• /
• 제15권4호
• /
• pp.11-17
• /
• 1997

Impulsive vibration velocity is monitored at the surface and the boundary surface of rocks as various impulsive forces of horizontal and vertical directions were given to rocks which had difference in uniaxial compressive strength for investigate to the vibration velocity of rocks according to the impulsive direction and the monitoring site. The vibration velocity of the boundary surface of rocks was about 2.9 times or much larger than that of the surface at the same scaled distance in the case of horizontal impulsive forces, and was above 4.2 times in the case of vertical impulsive forces. The attenuation exponents of the vibration velocity equations in the surface and the boundary surface of rocks make a vast difference with the impulsive directions, but is makes little difference in the case of the same impulsive direction. The ratio of vibration constants of the surface to the boundary surface of rocks is that square and cube root scaled equation is a range of 2.7∼3.0 and 4.9∼5.0 respectively in the case of horizontal impulsive forces, and is a range of 4.2∼5.7 and 7.7∼11.5 respectively in the case of vertical impulsive forces.

• 한국멀티미디어학회논문지
• /
• 제22권1호
• /
• pp.110-116
• /
• 2019

Virtual reality (VR) sickness can have an influential effect on the viewing quality of VR 3D contents. Particularly, watching the 3D contents on a head-mounted display (HMD) could cause some severe level of visual discomfort. Despite the importance of assessing the VR sickness, most of the recent studies have focused on unveiling the reason of inducing VR sickness. In this paper, we subjectively measure the level of VR sickness induced in the viewing of omnidirectional 3D graphics contents in HMD environment. Apart from that, we propose an objective assessment model that estimates the level of induced VR sickness by calculating the difference between head movement velocity and global camera motion velocity.

• 소성∙가공
• /
• 제11권3호
• /
• pp.262-268
• /
• 2002

The bending process for the rectangular and circular curled tube can be developed by the hot metal extrusion machine with the multiple punches moving in the different velocity. The bending phenomenon has been known to be occurred by the different of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets through the multi-hole container and by the cohesion of billet Inside the porthole die chamber. The bending phenomenon can be controlled by the two variables, the one of them is the difference of velocity at the die edit section by the different velocity of billets through the multi-hole container The other is the difference by the different hole diameter The results of the experiment show that the rectangular curved tube can be formed by the extrusion process, that the curvature of the curved product can be controlled by the velocity of punch and the diameter of container hole, that the defects such as the distortion of section and the thickness change of the wall of tube and the folding and wrinkling of thin tube did not happen after the extra-bending processing by the extrusion bending machine.