• 한국연소학회지
• /
• 제5권2호
• /
• pp.69-78
• /
• 2000

Reattachment characteristics of laminar flames in partially premixed jets are studied for propane fuel mixed with air. As the flow rate decreases, liftoff height is decreased nonlinearly and the flame reattaches to a nozzle at a certain liftoff height. Using a jet theory by taking into account a virtual origin, it is predicted that flow velocity along a stoichiometric contour has a maximum value near nozzle. With this velocity characteristics, it is shown that reattachment mechanism can be explained by a balance between flame speed and flow velocity. Predicted displacement speeds at reattachment and liftoff agree qualitatively well with experimental findings.

• Nuclear Engineering and Technology
• /
• 제35권5호
• /
• pp.369-377
• /
• 2003

Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in pressurized heavy water reactors, there has been a strong incentive to develop a method for the non-destructive detection of blisters grown on the tube surfaces. However, because there is little mismatch in acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and zirconium matrix with conventional ultrasonic methods. This study has focused on the development of a special ultrasonic method, so called ultrasonic velocity ratio method for a reliable detection of blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of the Zr-2.5Nb pressure tube using a cold finger attached to a steady state thermal diffusion equipment. To maximize a difference in the ultrasonic velocity in hydride blisters and the zirconium matrix, the ultrasonic velocity ratio of longitudinal wave to shear wave, $V_L/V_S$, has been determined based on the flight time of the longitudinal echo and reflected shear echo from the outer surface of the tubes. The feasibility of the ultrasonic velocity ratio method is confirmed by comparing the contour plots reproduced by this method with those of the blisters grown on the Zr-2.5Nb pressure tubes.

• 대한기계학회논문집B
• /
• 제27권3호
• /
• pp.357-366
• /
• 2003

An experimental study is performed to investigate characteristics of near of wakes of circular cylinders with serrated fins using a hot-wire anemometer for various freestream velocities. The main focus of this paper is to investigate a reason why a vortex formation length is increased suddenly. Velocity of the fluid which flow through fins decreases as fin's height and freestream velocity increases and fin pitch decreases, and a thickness of boundary layer increases. The finned tube has a lower velocity gradient when the higher boundary layer grows. This velocity gradient on finned tube makes a weak shear force in the wake and moves to downstream in a state of lower momentum transfer between the freestream and the wake. The phenomenon makes a vortex formation length increased suddenly. The fluctuations of the velocity distributions on the finned tube and (equation omitted) = 1.0 contour line in the vortex formation region decreases when the fin height increases and the pitch decreases.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.439-449
• /
• 2002

Experimental investigations of the flow structure and heat transfer enhancement in a channel with a built-in circular cylinder and a wing-let type vortex generator are presented. Without any vortex generators, relatively low heat transfer takes place in the downstream of the circular cylinder where is a recirculation region with low velocity fluid is formed. However with a wing-let type longitudinal vortex generator in the wake region behind the cylinder, heat transfer in the region can be enhanced. In order to control the strength of longitudinal vortices, the angle of attack of the vortex generators is varied from $20^{circ} to 45^{\circ}$, but spacings between the vortex generations are fixed to be 5 mm. The 3-dimensional mean velocity field downstream of the vortex generator is measured by a five-hole pressure probe, and the hue-capturing method using thermochromatic liquid crystals has been used to provide the local distribution of the heat transfer coefficient. The vorticity field and streamwise velocity contour are obtained from the velocity field. Streamwise distributions of averaged Stanton number on the measurement planes show very similar trends for all the experimental cases($\beta=20^{circ}, 30^{circ} and 45^{\circ}$). Circulation strength and heat transfer coefficient have the maximum values when the angle of attack($\beta$) is $30^{\circ}$.

• 상하수도학회지
• /
• 제30권6호
• /
• pp.745-753
• /
• 2016

The objective of this study was to investigate design factors of the electrolysis reactor through the CFD(computational fluid dynamics) simulation technique. Analyses of velocity vector, streamline, chloride ion concentration distribution showed differences in flow characteristics between the plate type electrode and the porous plate type electrode. In case of the porous plate type electrode, chlorine gas bubbles generated from the anode made upward density flow with relatively constant velocity vectors. Electrolysis effect was more expected with the porous plate type electrode from the distribution of chloride ion concentration. The upper part of the electrolysis reactor with the porous plate type electrode had comparatively low chloride concentration because chloride was converted to the chlorine gas formation. Decreasing the size and increasing total area of rectifying holes in the upper part of cathodes, and widening the area of the rectifying holes in the lower part of cathodes could improve the circulation flow and the efficiency of electrolysis reactor.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.681-686
• /
• 2007

The flow analysis was made by applying the turbulent models in the scroll volume of centrifugal compressor. The $k-{\varepsilon}.\;k-{\omega}$, Spalart-Allmaras and reynolds stress models are used in which the hybrid grid is applied for the simulation. The velocity vector the Pressure contour. the change of residual along the iteration number. and the dynamic head are simulated by solving the Navier-Stokes equations for the comparison of four example cases.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1993년도 춘계학술대회논문집; 한국과학연구소, 21 May 1993
• /
• pp.128-133
• /
• 1993

본 연구에서는 보강 원통쉘에 대하여 주위 유체의 영향을 고려하여 진동 및 음향방사를 해석하였다. 원통셀의 운동방정식은 Donnell 이론을 적용하였으 며, Contour 적분을 풀지 않고 FFT 알고리즘(Fast Fourier Transform Algorithm)을 이용하여 원통쉘의 진동을 계산하였다. 현재까지의 방사패턴에 관한 연구는 주로 원주 방향에 집중되어 왔으나, 보강 원통쉘의 방사패턴은 원추파 모형에 가까우므로 극좌표 .theta. 방향에 대한 음향방사 패턴에 관한 연구가 이루어져야 한다. 그러므로, 본 연구에서는 극좌표에 관한 방사패턴 에 관하여 주로 고찰하였다.

• 대한기계학회논문집
• /
• 제7권4호
• /
• pp.361-371
• /
• 1983

The turbulent structures of the free plane jet and two dimensional impinging jet are investigated experimentally. In order to get the two dimensional jet, the contour of the cubic equation suggested by Morel is used for a contracting nozzle. A linearized constant-temperature hot-wire anemometer is used for measurement. Mean velocities and turbulent intensities are measured along the centerline of the jet. Jet halp width spatial double velocity correlation coefficients and integral length scales are obtained. It is established that the free plane jet is truly self-preserving about 40 slot widths downstream of the nozzle. The experiments for the impinging jet are carried out at four different impingement wall locations within the self-preserving region of the free plane jet, and comparing the results with that of free plane jet, the mean velocity is changed in the region of 0.25H and turbulent intensities are affected in the region of 0.2H from the wall, respectively, where H means the distance between the nozzle exit and the wall.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.42-45
• /
• 2002

General wheel mark in mono-crystalline silicon wafer finding is able to be expected because it depends on radius ratio and angular velocity ratio of wafer and wheel. The pattern is predominantly determined by the contour of abrasive grits resulting from a relative motion. Although such a wheel mark is made uniform pattern if the process parameters are fixed, sub-surface defect is expected to be distributed non-uniformly because of characteristic of mono-crystalline silicon wafer that has diamond cubic crystal. Consequently it is considered that this phenomenon affects the following process. This paper focused on kinematic analysis of wafer grinding process and simulation program was developed to verify the effect of process variables on wheel mark. And finally, we were able to predict sub-surface defect distribution that considered characteristic of mono-crystalline silicon wafer

• 자원환경지질
• /
• 제14권3호
• /
• pp.143-153
• /
• 1981

Seismic risk maps in Korea are made using Korean historical and modern earthquake data. The risk maps made by several method are presented in contour line of vibratory ground motion(acceleration, velocity, and displacement). The method used are Kawasumi (1951), Kanai (1968), and Hsich et al (1975) method. The maps made by Kawasumi (1951) method represent the acceleration distribution ground and those by Kanai (1968) method show the acceleration, velocity, and displacement at bed rocks, The risk analysis by the method of Hsich et al (1975) shows the probability of acceleration at each of soft, medium and hard grounds in each tectonic province in Korea.